Light Symphony LS30505SCC Bedienungsanleitung

PUMP CONTROL

It may be desirable to exclude circuits from the global ‘Garden On/Off’ buttons on

the remote, so they stay on when the lighting is switched off. This unit can be

programmed to ignore whole “GARDEN ON/OFF” commands by selecting ‘Set-

up’, pressing Garden Off (to switch off the circuit), then pressing the Dim Up &

Down keys together, and then moving the slide switch back to Switch or Dim. As

before, the unit can be programmed into its own ‘Area(s)’ but will now ignore global

‘Garden On/Off’’ commands.

Environmental Information for Customers in the European Union

European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its

packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product

should be disposed of separately from regular household waste streams. It is your responsibility to dispose

of this and other electric and electronic equipment via designated collection facilities appointed by the

government or local authorities. Correct disposal and recycling will help prevent potential negative

consequences to the environment and human health. For more detailed information about the disposal of your old

equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.

NOTE;

Rights reserved to change the specification of this product without prior notice.

SPECIFICATIONS

Voltage 220-240V AC / 50Hz

Output Rating 250W

Minimum non-Inductive Load 0W (nil)

Minimum Inductive Load 10W each channel

Output Type Switched or Dimming (Leading-edge)

Protection Internal Thermal fuse

Weather Resistance IP68

Physical 50 x 50 x 25mm / 0.1Kg

Ambient Temp. -10°C to +40°C

INTRODUCTION

The ‘Lighting Control Module’ is for switching and/or dimming a lighting

circuit. It may be used with all lighting types including mains-halogen,

magnetic low-voltage transformers, most electronic transformers, (compact)

Fluorescent, Metal-Halide, Sodium and LED. Its output is selectable as

dimmable or switching and is suitable for all load types. Before use, ensure the

unit is set correctly, if unsure select ‘Switching’. The unit is designed for

outdoor installation but take note of the safety instructions below.

SAFETY INSTRUCTIONS

REMEMBER ELECTRICITY CAN KILL

IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN

1. Mount the unit in a safe position to avoid possible damage by mowers or

other garden tools. This unit must not be buried without proper protection.

2. The unit is a double-insulated and therefore requires no earth.

3. The electrical supply must be protected at source by an ‘Earth Leakage’

circuit breaker and suitably low rated fuse (0.5A per 100W’s of load).

4. Where 230V power is routed outside, national wiring regulations must be

adhered to. For UK installations rugged ‘Concentric’ type cable is

recommended above ground.

5. Where 230V power cable is buried, ‘Steel Wire Armoured’ cable must be

used. Buried cables must be at least 450mm (18”) below the surface.

6. BURN HAZARD: Take care not to touch hot lamps and keep children

away.

7. Fully loaded, this lighting module will generate up to 4½Watts of heat.

Ensure adequate space or ventilation to avoid over-heating

ISSUE 1.0

Single Channel ‘Lighting Control Module’

ELECTRICAL INSTALLATION

The unit must be installed by a qualified electrician working to national Electrical

ulations.

TESTING & SET-UP

2. Set the MODE switch to SWITCH or DIM to suit the lamp type.

Do not attempt to dim non-dimmable lighting or damage may result.

3. To test the unit is working, press “Garden On/Off” on the remote control.

4. The LED will blink when a wireless command is received.

5. From the factory, the unit only responds to Garden On/Off but can be

programmed to respond to other lighting Area’s using the procedure below;

AREA PROGRAMMING

The lighting channel (circuit) can be included in any number of Light Symphony’s

‘AREAs’. To program the unit into a new ‘Area’ key on the remote;

1. Slide the MODE switch to the ‘Set-up’ position.

(the LED will blink to show the memory is open).

2. Use the ‘Area’ key on the remote*to switch ON the lamp.

( *NOTE: can also use any other Light Symphony transmitter)

3. While the lamp is ON, move the Slide switch to SWITCH or DIM.

The LED will stop flashing and the unit will now be included in the

new Area. Teach other Areas by repeating this process.

The unit can be removed from an ‘Area’ using the same procedure, but with the

lamp OFF when the slide switch is moved from Set-up to SWITCH or DIM.

e.g. Slide the switch to ‘Set-up’, use the Area key you wish to erase to switch OFF

the lamp, then move the slide switch to SWITCH or DIM.

NOTE: The Set-up function will close automatically after 20 seconds if no button

is pressed (LED stops flashing). If required, re-enable it using the slide switch.

SCENE MEMORY

The 29 Area memories can also be used to create lighting Scene’s, where the

whole garden’s lighting configuration and dim-levels can be stored and recalled

with a single button-press. Scene setting is more relevant to dimmable lighting,

but switched scenes are also possible using Light Symphony.

To create a new scene, use the above Area Programming procedure and use the

remote’s Dim keys to set the level before moving the slide switch back to

SWITCH/DIM.

Walk around the garden configuring each lighting controller in turn in the same

way, so all lighting controllers respond to the same Area key.

LIGHT SHOW

By default, all circuits will be included in the light show. To configure which

channels should be included move the slide switch to set-up and press the

‘Rainbow’ key on the remote control two times to switch on the lamp. Circuits

that were ‘off’ when the memory closes will no longer be part of the show.

WIRING

NOTE: NOT suitable for dimming very small transformers (less than 10W). If

the lamp flickers, the transformer is too small or not compatible, Switch

off immediately to prevent damage to the Transformer and/or unit.

ISSUE 1.0

TOP VIEW

MODE

Switch

DIM

SWITCH

SET-UP

Store LED

BOTTOM VIEW

BROWN

BLUE

BLACK

SUPPLY IN

Live Neutral

Transformer

(if required)

ANTENNA

(no connection)

LAMP

Andere Light Symphony Controller Handbücher

Light Symphony

Light Symphony iTimer Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung