Lightforce HTX2 Bedienungsanleitung
1
1
USER INSTRUCTIONS
HTX2
HYBRID DRIVING LIGHT.
2USER INSTRUCTIONS LIGHTFORCE.COM
KIT CONTENTS
• 1 x 230mm HTX2 Hybrid Driving light
• 1 x Spot lter (tted to light)
• 1 x Reversible mounting bracket (tted loose
to light)
• 2 x M10 x 35mm stainless steel hex bolts with
washers and Nyloc®nuts (side bolts tted to
light)
• 1 x M10 x 35mm stainless steel hex bolt with
washer and Nyloc®nut (tted to bracket for
mounting)
• 1 x 4-pin waterproof harness adaptor
• 2 x M6 x 30mm stainless steel hex bolts with
washers and nuts (in bag) for optional extra
mounting security (see note on Page 4)
• 1 x Xtreme Top Stay Bracket (24V versions only)
• 1 x User instructions.
XTREME TOP STAY BRACKET
(HTXMK2TSB)
Optional Xtreme Top Stay Bracket is supplied as
standard with 24V version.
TOOLS REQUIRED
• 17mm and 11mm socket on ratchet
• Torque wrench (recommended).
NOTE
Drawing shown is with lter removed.
3
3
GENERAL CARE AND SAFETY TIPS
To wash your lights, use plenty of warm soapy water and a soft cloth only (this prevents surfaces
from marking). Never use any solvent based cleaners or industrial detergents when cleaning these lights.
Handle the base of the bulb only, if the glass gets dirty then clean with isopropyl alcohol or methylated
spirits.
WARNING
High intensity light source. Do not look directly into the light during operation, eye injury may result.
IMPORTANT NOTES
1. Mounting points vary in design and load capacity. Ensure the light is within the manufacturer’s
recommended weight specications before tment
2. Before tting the stainless steel hardware, it is recommended that you apply a small amount of anti-seize
to the thread of the 35mm mounting bolts
3. The optional Xtreme Top Stay Bracket (HTXMK2TSB) provides additional stability during extreme driving
conditions (included with 24V version only).
MOUNTING BRACKET
1. Remove Nyloc®nut and M10 washer from M10 x 35mm bolt attached to the bottom of mounting bracket
2. Locate the bracket in a suitable position using the M10 x 35mm bolt. It is recommended that the base
area of the mounting bracket is totally supported
3. Align the light to the preferred driving position
4. Fit the washer and M10 Nyloc®nut then tighten using a 17mm socket and ratchet to specied torque
(35Nm) - do not use a rattle gun
5. Tighten 2 x M10 x 35mm side bolts to the recommended torque (35Nm).
4USER INSTRUCTIONS LIGHTFORCE.COM
NOTE
Additional mounting bolts are provided - If extra mounting security is required or you have a problem with
your light rotating, there are two mounting holes either side of the main M10 mounting bolt that can be
utilised. Also the optional Xtreme Top Stay Bracket provides additional stability during tough terrain.
Side Bolt
M10 x 35
M6 x 30
Optional tment
Mounting Bolt
M10 x 35
Side Bolt
M10 x 35
Front Facing
Optimum Mounting
Bracket Position
M6 x 30
Optional tment
5
5
ELECTRICAL CONNECTIONS
The HTX2 Hybrid Driving Light is tted with a waterproof 4 pin electrical connector.
The mating connector included in the kit is tted with short lengths of cable for integration with an appropriate
wiring harness. NOTE: Harness must be capable of 15A per light.
If the vehicle’s existing wiring harness is suitable, the included connector needs to be tted directly to your
existing driving light circuit.
CONNECTOR WIRE COLOUR IDENTIFICATION
1. Red: Positive input for HID – connect to positive output (87) wire on relay
2. Black: Negative for HID - connect to negative (earth)
3. Yellow: Positive input for LED - connect to positive output (87) wire on second relay
4. Blue: Negative for LED - connect to negative (earth).
Blue
Yellow
Red
Black
NOTE
For maximum performance, three mode operation and safety we recommend the use of the optional
wiring harness (part number LFDLHDS) to t the 12V version of the HTX2 to a vehicle – for tment follow
the installation instructions included with the harness.
The 24V version of the HTX2 is commonly installed on various commercial vehicles and the use of a
customised harness is usually required.
Once all the electrical connections have been made, align the light to the desired position and tighten all
bolts as per recommended torque specications (see specications section).
CAUTION
Improper installation of the connector will affect the reliability and operation of your lights.
6USER INSTRUCTIONS LIGHTFORCE.COM
• LED power: 80W
• HID power: 50W
• Effective lumens: 8050
• Input voltage range: 10-16V DC (12V version)
• Current draw: 11.5A @ 13.2V (12V version)
• Input voltage range: 18-30V DC (24V version)
• Current draw: 6A @ 24V (24V version)
• LED colour temperature: 5000K
• HID colour temperature: 5000K
• LED lifespan: Up to 50,000 hours
• Operating temperature: -40°C to 63°C (-40°F
to 145°F)
• Dimensions: 230mm (9.06”) W x 250mm
(9.86”) H x 122mm (4.80”) D
• Weight including bracket: 2.3kg (5.07lb).
TECHNICAL SPECIFICATIONS
CERTIFICATIONS
• IP68 and IP69K rated to protect against moisture / contaminant ingress
• CE Certied. The CE mark is an internationally recognised symbol declaring that the product complies with
stringent health, safety and environmental standards. Compliance limits electromagnetic emissions such
that the product does not affect radio reception and telecommunications.
RECOMMENDED WIRE SIZE
• 0.82mm2(AWG 18) minimum per circuit.
FASTENER TORQUE SPECIFICATIONS
• M10 x 35mm bottom mount bolt - 35Nm (26lb-ft)
• M4 x 10mm Rear cover - 2.5Nm (1.84lb-ft)
• M6 x 30mm additional bottom mounting bolts - 4Nm (2.95lb-ft).
7
7
ORDER CODE DESCRIPTION
LFDLHDS HTX / HTX2 dual switching dual relay harness (12V only)
HTXM2TSB HTX2 Xtreme Top Stay Bracket - (not compatible with original HTX)
HTXMK2SFL HTX2 spot lter - (not compatible with original HTX)
HTXMK2CFL HTX2 combo lter - (not compatible with original HTX)
HTXMK2BC HTX2 black cover - (not compatible with original HTX)
ATNSG2 Anti-theft nut kit - (not compatible with original HTX)
GL30 HID replacement 5000K bulb - (not compatible with original HTX)
DL230MB HTX / HTX2 replacement mounting kit
ACCESSORIES
8USER INSTRUCTIONS LIGHTFORCE.COM
WARNING
ALWAYS disconnect power before disassembly of light.
ALWAYS wear safety glasses when handling any bulb.
DO NOT handle the glass section of the bulb.
NOTE: Wearing clean cotton gloves is recommended while handling
internal components.
HID BULB REPLACEMENT
1. Disconnect power and remove the light from vehicle
2. Place light face down then evenly remove the four socket head screws (1) (using a 3mm hex
key) from the rear cover (2)
3. Remove the rear cover, then remove the globe by inverting the light and allowing the globe
to fall free of the housing (Note: the focal ring (5) may come out with the globe)
4. Place light face down
5. Disconnect cable from the HID bulb (3) by pulling on bulb connector (4) rmly and place bulb
on a at surface
6. Re-locate the focal ring into the reector with the stepped face facing inwards
7. Connect new HID bulb to connector (4)
8. Carefully position new HID bulb into focal ring (5)
9. Ret rear cover to housing ensuring the rear cover seal (6) and spring (7) are still in place. If
seal becomes dislodged ret to the rear cover.
10. Ret the four socket head screws to the specied torque of 2.5 Nm.
ELECTRICAL SHOCK
1
2
3
4
5
6
7
9
9
DRIVING LIGHT FILTERS
Durable polycarbonate covers should remain tted to your HTX2 Hybrid Driving Lights at all times. They are
capable of absorbing road grime and bombardment for many years. These replaceable covers should be
renewed from time to time to protect your investment and maintain maximum beam output. Your HTX2 Hybrid
Driving Light(s) come standard with spot lters. Clear combo lters are used to change the beam output of the
HID bulb only.
FILTER REMOVAL
• Filter is held in place by 4 clips
• Lift tab at bottom of light and pull lter away from bezel releasing the clips.
FILTER REFITTING
• Insert the lter at the top position
• Push lter onto bezel using lter tab until side clips are engaged
• Ensure lter is correctly aligned within bezel.
PLEASE NOTE
Lightforce driving lights are designed to be mounted in the horizontal/forward facing position only.
Pointing the light upwards can cause heat damage to the lens. Failure to comply with this requirement
may void warranty.
The HTX2 Black Covers should never be installed on your HTX2 Hybrid Driving Lights when they are in
operation as this can cause catastrophic failure due to overheating.
DO NOT REMOVE THE FRONT BEZEL. THIS MAY VOID WARRANTY.
10
USER INSTRUCTIONS LIGHTFORCE.COM
“Lightforce” means Lightforce Australia Pty Ltd
ABN 54 069 439 774 Address: 11 Manton Street,
Hindmarsh, SA, 5007. Telephone: +61 8 8440 0888.
“Lightforce Afliates” means Lightforce, Lightforce
related bodies corporate (within the meaning of
the Corporations Act 2001), and their respective
employees, ofcers, agents, and contractors.
“Warranty Period” means:
Lightforce products claimed for repair or replacement
under the conditions of a defect in materials or
workmanship within normal use and conditions,
are valid for the time period of three (3) years from
the date of purchase; except accessories, switches,
made-to-order items, custom built items, brackets,
fascia and harness, bulbs, batteries and mounts
which is one (1) year from the original date of
purchase specied on your sales receipt or invoice.
Only Lightforce products and parts which remain
unaltered from their factory supplied design are
eligible for warranty. Modications made to the
product, any collision or impact damage of any kind,
product tampered in any manner, including poor
installation will void warranty.
REPAIR OR REPLACEMENT OF A PRODUCT
OR PARTS:
A replacement product or part is warranted for the
balance of the period remaining on the original
product contract. A warranty replacement/repair
does not constitute a new warranty period of (3)
years or (1) year whichever is the correct warranty
period. Products and parts presented for repair or
replacement may be replaced by products of the
same type, or superseding designs.
Goods presented for repair may be replaced by
refurbished goods of the same type rather than being
repaired. Refurbished parts may be used to repair the
goods.
MAKING A CLAIM:
Under this warranty and unless Lightforce otherwise
agrees in writing, you bear the cost of claiming
under this warranty, Lightforce will however, bear
the reasonable cost of transporting the product to
Lightforce and returning the product to you.
Lightforce must assess warranty claims before a
claim can be granted unless otherwise arranged for
and by Lightforce.
To make a claim you will need;
• The receipt of purchase or similar proof AND
• The product being claimed for AND
• Have registered the claim with Lightforce by;
Calling 1800 03 03 08 and speaking with a warranty
support ofcer OR
A support ofcer will raise a case number and
provide you with any necessary labelling and freight
paperwork to process the claim.
USE OF PERSONAL INFORMATION:
This warranty will not apply if you do not supply to
us or to our Lightforce Afliates information that
we reasonably request to enable us to perform our
obligations under this warranty. You have the right to
access your personal contact information and request
correction of any errors in it pursuant to the Privacy
Act 1988 by contacting Lightforce.
WARRANTY CONDITIONS FOR AUSTRALIA
Inhaltsverzeichnis
Andere Lightforce Beleuchtungsausrüstung Handbücher
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
