Lightolier END FEED AND FLOATING CANOPY MOUNTING KIT Gebrauchsanweisung

READ AND UNDERSTAND ALL TRACK, CONNECTOR, FEED-IN-KITS, AND ACCESSORY

INSTRUCTION SHEETS BEFORE INSTALLING ANY PROSPEC®TRACK ITEM.

This fixture is intended for installation in accordance with the National Electrical Code and local or Federal

code specifications. To assure full compliance with codes and regulations, check with your local electrical

inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

LIGHTOLIER a GENLYTE company.

631 Airport Road, Fall River, MA 02720

INSTRUCTION SHEET NO.

IS:26060

0597 Page 1 of 2

END FEED AND FLOATING CANOPY MOUNTING KIT - FLUSH AND STANDOFF VERSIONS

FOR USE WITH PROSPEC®SURFACE MOUNT TRACK SYSTEMS ONLY

END FEED MOUNTING INSTRUCTIONS

(Flush 26060WH, BK and Standoff 26061WH, BK)

Mounting the CANOPY at the end of FEED TRACK or directly above

a FEED CONNECTOR.

1. Mark CENTER LINE for TRACK through CENTER LINE of OUT-

LET BOX.

2. NOTE: The CANOPY mounts to a 3 or 4” OCTAGON OUTLET

BOX. The MOUNTING HOLES of the OUTLET BOX should be at

45° to the longitudinal axis of the TRACK. (Fig. 1)

3. Remove the KNOCK OUT PLATE from the FEED TRACK or

CONNECTOR (retain the SCREW). (Fig. 2)

4. Prepare TAB on the PLATE ASSEMBLY as follows:

• FEED TRACK: DO NOT BREAK ANY TAB. (Fig. 2)

• POWER EXTENSION, IN-LINE, “T”, AND “X” CONNECTORS:

BREAK THE 90° TAB OFF THE PLATE ASSEMBLY. (Fig. 3)

• “L” CONNECTOR: BREAK THE 90° TAB AND THE STRAIGHT

TAB FROM THE PLATE ASSEMBLY. (Fig. 4)

5. Attach the PLATE ASSEMBLY onto the FEED TRACK or

CONNECTOR using the SCREW. (Fig. 2 &3)

6. Mount the TRACK to the ceiling (see instruction sheet

IS:26000 provided with the TRACK) passing the wires through

the center of the PLATE ASSEMBLY.

7. Rotate the PLATE ASSEMBLY until the SLOTS are in-line with

the MOUNTING HOLES on the J-BOX.

8. Secure the PLATE ASSEMBLY to the J-BOX using the THIN

HEAD SCREWS. (Fig. 5)

9. Attach the GROUND WIRE on the CANOPY PLATE to the

GROUND LEAD or GROUND TERMINAL in the J-BOX. (Fig. 5)

10. WHEN USING THE FLUSH CANOPY 26060WH/BK.

Slide the CANOPY PLATE between the CONNECTOR and

CROSS BAR on the PLATE ASSEMBLY. For added security of

CANOPY PLATE: Drill a hole in CANOPY PLATE and secure to

ceiling with a screw.

11. WHEN USING THE STANDOFF CANOPY 26061WH/BK

Slide the CANOPY PLATE between the CROSS BAR and NUT

on the PLATE ASSEMBLY. Rotate the NUT to secure the

CANOPY PLATE against the ceiling. (Fig. 8)

NOTE: THE CROSS BAR MUST COVER THE SLOT IN

THE CANOPY PLATE AFTER ASSEMBLY.

12. Follow the instructions for wiring on the instruction sheet

included with the “FEED TRACK” or “CONNECTOR”.

CAUTION: TURN OFF POWER AT FUSE BOX BEFORE

INSTALLING THE CANOPY KIT

POWER EXTENSION

CONNECTOR

PLATE

ASSEMBLY

SCREW

90 ° TA B

KNOCK OUT

PLATE

FIG. 2

FIG. 3

PLATE

ASSEMBLY

SCREW

KNOCK OUT

PLATE

FEED TRACK

FIG. 4

STRAIGHT

TAB

PLATE

ASSEMBLY

90 ° TA B

KNOCK OUT

PLATE

“L” CONNECTOR

CANOPY

PLATE

GROUND

WIRE

THIN HEAD

SCREW

J-BOX

FIG. 5

CROSS BAR

45 °

TRACK UNIT LONGITUDINAL

TRACK

OUTLET BOX

MOUNTING HOLE

FIG. 1

READ AND UNDERSTAND ALL TRACK, CONNECTOR, FEED-IN-KITS, AND ACCESSORY

INSTRUCTION SHEETS BEFORE INSTALLING ANY PROSPEC®TRACK ITEM.

This fixture is intended for installation in accordance with the National Electrical Code and local or Federal

code specifications. To assure full compliance with codes and regulations, check with your local electrical

inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

LIGHTOLIER a GENLYTE company.

631 Airport Road, Fall River, MA 02720

INSTRUCTION SHEET NO.

IS:26060

0597 Page 2 of 2

FLOATING FEED MOUNTING INSTRUCTIONS

(Flush 26060WH, BK and Standoff 26061WH, BK)

Mounting the CANOPY at some distance away from the end of the

FEED TRACK or FEED CONNECTOR.

NOTE: Hardware is supplied to mount the CANOPY a maximum

of 4 feet from the FEED CONNECTOR. DO NOT EXCEED

THIS DISTANCE.

1. Mark CENTER LINE of TRACK through CENTER LINE of OUT-

LET BOX.

2. NOTE: The CANOPY mounts to a 3 or 4” OCTAGON OUTLET

BOX. The MOUNTING HOLES of the OUTLET BOX should be at

45° to the longitudinal axis of the TRACK. (Fig. 1)

3. Break the BARRIER off the FEED CONNECTOR or FEED TRACK.

(Fig. 6)

4. Remove the DEAD END from the TRACK and retain.

5. Assembly the “U” BRACKET onto the PLATE ASSEMBLY using

the FLAT HEAD SCREW. (Fig. 6)

6. Run the feed wires along the top of the TRACK and into the

FEED CONNECTOR or FEED TRACK. (2 HOTS, 2 NEUTRALS,

AND GROUND; MAXIMUM)

7. NOTE: USE 12 GA. COPPER THHN WIRE INCLUDING

GROUND. IF STRANDED 12 GA WIRE IS USED THE ENDS

MUST BE TINNED.

8. Cut the WIRE COVER to the desired length.

9. Slide the WIRE COVER (over the wires) and PLATE ASSEMBLY

into the TRACK. NOTE THE POSITION OF THE 90° TAB IN

RELATION TO THE FEED-IN POINT. Pass the wires

through the center hole of the PLATE ASSEMBLY.

10. Secure the PLATE ASSEMBLY to the TRACK by tightening the

SCREW. THE WIRE COVER MUST COVER THE ENTIRE

LENGTH OF WIRES ON TOPS OF THE TRACK.

11. Mount the TRACK to the ceiling (see instruction sheet 26000

provided with the track or IS:26478). Positioning the PLATE

ASSEMBLY over the J-BOX.

12. Splice the wires from the track to the wires in the J-BOX.

BLACK TO BLACK, WHITE TO WHITE, AND GROUND TO

GROUND.

13. Rotate the PLATE ASSEMBLY until the SLOTS are in-line with

the MOUNTING HOLES on the J-BOX.

14. Secure the PLATE ASSEMBLY to the J-BOX using the THIN

HEAD SCREWS. (Fig. 7)

15. Attach the GROUND WIRE on the CANOPY PLATE to the

GROUND LEAD or GROUND TERMINAL in the J-BOX. (Fig. 7)

16. WHEN USING THE FLUSH CANOPY 26060WH/BK.

Slide the CANOPY PLATE between the TRACK and CROSS

BAR on the PLATE ASSEMBLY. For added security of CANOPY

PLATE: Drill a hole in CANOPY PLATE and secure to ceiling

with a screw.

17. WHEN USING THE STANDOFF CANOPY 26061WH/BK.

Slide the CANOPY PLATE between the CROSS BAR and NUT

on the PLATE ASSEMBLY. Rotate the NUT to secure the

CANOPY PLATE against the ceiling. (Fig. 8)

18. NOTE: THE CROSSBAR MUST COVER THE SLOT IN

THE CANOPY PLATE AFTER ASSEMBLY.

19. Follow the instructions for wiring on the instruction sheets

included with the the “FEED TRACK” or “CONNECTOR”.

20. Assembly the DEAD END into the end of the TRACK.

FIG. 6

BARRIER DEAD

END

U BRACKET

90 ° TA B

FLAT HEAD

SCREW

PLATE

ASSEMBLY

WIRE COVER

TRACK UNIT

FEED CONNECTOR

FEED IN POINT

U BRACKET

FIG. 8

TRACK UNIT

J BOX CANOPY

PLATE

POWER EXTENSION

CONNECTOR

NUT

FIG. 7

CANOPY PLATE

J-BOX

PLATE

ASSEMBLY

WIRE COVER

POWER EXTENSION

CONNECTOR

TRACK UNIT

THIN HEAD

SCREW

CROSS BAR

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lightolier Beleuchtungsausrüstung Handbücher

Lightolier

Lightolier Lytespan 8727M16 Bedienungsanleitung

Lightolier

Lightolier Lighting Systems F7000-12 Bedienungsanleitung

Lightolier

Lightolier LyteCaster 302MRIC7X Bedienungsanleitung

Lightolier

Lightolier ProSpec 26238W Bedienungsanleitung

Lightolier

Lightolier Calculite C6E17OVW Bedienungsanleitung

Lightolier

Lightolier FA01 Bedienungsanleitung

Lightolier

Lightolier Lighting Systems Baselyte-BSL6 Bedienungsanleitung

Lightolier

Lightolier Lighting Systems F7000-22 Bedienungsanleitung

Lightolier

Lightolier Lytespan 8745 Bedienungsanleitung

Lightolier

Lightolier Alcyon 23S39T6 Leitfaden

Lightolier

Lightolier Calculite C4MRP Bedienungsanleitung

Lightolier

Lightolier Alter Waves QVL2GPFSS432 Bedienungsanleitung

Lightolier

Lightolier Calculite C6P38MHA Bedienungsanleitung

Lightolier

Lightolier LSC-3 Bedienungsanleitung

Lightolier

Lightolier Lighting Systems Baselyte-BSL21 Bedienungsanleitung

Lightolier

Lightolier FRS2GFW26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 23MHRNF Bedienungsanleitung

Lightolier

Lightolier FBP Low Profile Fluorescent Emergency Ballast... Bedienungsanleitung

Lightolier

Lightolier PTS6-1 Bedienungsanleitung

Lightolier

Lightolier Calculite C12E28VN Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17RS Bedienungsanleitung

Lightolier

Lightolier Calculite C6AW Bedienungsanleitung

Lightolier

Lightolier Lytespan 83T4S Bedienungsanleitung

Lightolier

Lightolier EYS Series 25* louver Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung