Lightware DVI-OPT-RX220-Pro Bedienungsanleitung

www.lightware.eu Firmware version: 1.1.1

For technical support contact support@lightware.eu Document revision: 1.1

DVI-OPT-RX220-Pro

Quick Start Guide

Installation

1. Connect the DVI display devices to the DVI OUTPUT connectors.

2. Connect a compatible Lightware fiber transmitter unit with a multimode fiber cable to the

FIBER INPUT connector. Connect an LC optical cable to the “channel B” LC connector, or

use a Neutrik OpticalCON cable.

3. Power on the fiber transmitter, and the DVI source (computer).

4a. To use the built-in power supply: set the power selector switch to “I”, and connect the IEC

power cable. Now the unit is ready to be used.

4b.To power the unit remotely: works only if the receiver is connected to a

DVI-OPT-TX220-PRO with a Neutrik hybrid fiber cable. Set the power selector switch to “II”.

5. Power on the connected display devices. They will display the picture from the DVI source

(computer).

Power LED

Lights if the unit is powered on.

Laser LED

Green light indicates that the laser is properly detected on

the optical input. Red blinking light indicates low laser level,

or no incoming signal.

Signal LED

Indicates valid DVI clock signal reception.

Monitor LEDs

Each LED indicates if a display device is connected to the

corresponding DVI output.

AC connector

Standard IEC power connector.

Break-out conn.

The break-out LC connector is internally connected to output

A of the Neutrik connector.

Neutrik connector

Channel B carries the signal to this unit’s optical receiver,

and channel A carries any optical signal to the break-out LC

connector.

Serial port

The device is controllable by Lightware Matrix Control

software via RS-232 connection.

Power selector

In position “I” the receiver unit is powered by its own built-in

power supply. In position “II” the receiver unit is powered

through special hybrid fiber cable, type’Neutrik 2M-4S75’.

DVI outputs

Two display devices can be connected. The resolution and

pixel clock frequency are the same on both DVI connectors.

Alarm outputs

DVI signal detection and laser detection signals with ground

reference are available on a three-pole Phoenix connector.

Power LED

Laser LED

Signal LED

Monitor LEDs

Power selector

AC connector

Neutrik connector

Serial port

Break-out connector

Alarm outputs

DVI outputs

Andere Lightware Extender Handbücher

Lightware

Lightware VINX-110-HDMI-DEC Bedienungsanleitung

Lightware

Lightware HDMI-TPS-TX210 Bedienungsanleitung

Lightware

Lightware DVI-HDCP-TP-TX50 Bedienungsanleitung

Lightware

Lightware DVI-HDCP-TPS-TX95 Bedienungsanleitung

Lightware

Lightware DP-OPT-TX150 Bedienungsanleitung

Lightware

Lightware OPTJ Power tray Series Bedienungsanleitung

Lightware

Lightware HDMI20-OPTC-TX220-Pro Bedienungsanleitung

Lightware

Lightware HDMI-3D-OPT-TX210RAK Bedienungsanleitung

Lightware

Lightware VINX-120AP-HDMI-ENC-DNT Bedienungsanleitung

Lightware

Lightware UBEX-MMU-X200 Bedienungsanleitung

Lightware

Lightware UBEX-PRO20-HDMI-F100 Bedienungsanleitung

Lightware

Lightware DVI-OPT-TX220-ST-Pro Bedienungsanleitung

Lightware

Lightware DVIDL-OPT-TX200 Bedienungsanleitung

Lightware

Lightware HDBaseT HDMI-TPS-RX110AY Bedienungsanleitung

Lightware

Lightware HDMI-TPS-RX220AK Bedienungsanleitung

Lightware

Lightware EDID MANAGER V4 Bedienungsanleitung

Lightware

Lightware HDBaseT HDMI-TPS-RX110AY Bedienungsanleitung

Lightware

Lightware VINX-120-HDMI-ENC Bedienungsanleitung

Lightware

Lightware DVI-TP-RX100 Bedienungsanleitung

Lightware

Lightware HDMI-TPS-TX97 Bedienungsanleitung

Lightware

Lightware FP-HDMI-TPS-97-GB3 Bedienungsanleitung

Lightware

Lightware VINX-110-HDMI-DEC Bedienungsanleitung

Lightware

Lightware HDMI-TPS-TX95 Bedienungsanleitung

Lightware

Lightware HDMI-3D-OPT-TX210A Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung