Lightwave LW821 Bedienungsanleitung
Connect Series
www.lightwaverf.com
Inline Relay (500W)
Model No. LW821
Instruction Manual
Version 2
EC DECLARATION OF CONFORMITY
Responsible Authority:
LightwaveRF PLC,
Innovation Campus Birmingham
Faraday Wharf
Holt Street
Birmingham
B7 4BB
Tel: +44 (0)121 250 3625
Email: [email protected]
Model Number(s): JSJSLW821
Description: Inline Relay
Directives this equipment
Complies with: 2006/95/EC The Low Voltage Directive N/A
2004/108/EEC The Electromagnetic Compatibility Directive
1999/5/EC R&TTE Directive
93/68/EEC CE Marking Directive
Standards Applied in order to verify compliance
Safety: BS EN 60730-1: 2011
Health:
R&TTE: EN 301 489-1 V1.9.2: (2011-09), EN 301 489-3 V1.4.1: (2002-08)
EN 300 220-1 V2.1.1: 2006, EN 300 220-2 V2.1.2: 2007
EMC: EN 301 489-1 V1.9.2: (2011-09), EN 301 489-3 V1.4.1: (2002-08),
EN 55022: 2010, EN 61000-3-2: 2006 +A1: 2009 +A2: 2009 Class A,
EN 61000-3-3: 2008, EN61000-4-2: 2009,
EN 61000-4-3: 2006 +A1: 2008 +A2: 2010, EN 61000-4-4: 2012,
EN 61000-4-5: 2006, EN 61000-4-6: 2009, EN 61000-4-11: 2004
For and on behalf of LightwaveRF PLC
----------------------------------------
Name J Shermer
Position Managing Director
What do I need?
How do I get started?
The relay is designed to remotely turn on/o
lighting or power circuits (max 500W) or to
control door, window or curtain openers. You must
understand how your devices need to be wired
and how to safely turn o the electricity supply.
You will also need suitable electrical screwdrivers.
Please refer to the following installation and
setup instructions that will guide you through
the installation and setup process.
Help video & further guidance
For additional guidance, and to watch a video
that will help guide you through the installation
process, please visit the support section on
www.lightwaverf.com
Get Started
Power LED. When
illuminated the
relay is powered.
Mounting hole.
On/o & linking
button.
Overview
IMPORTANT: All LightwaveRF products can be legally DIY installed in your
own home; however, if in doubt, always consult a qualified electrician or
heating engineer. It is important to install this product in accordance with
the following instructions. Failure to do so may void your warranty.
Installation
Fuse
compartment.
Wiring
terminals. Screw cover.
Installation
The Inline relay requires mains power to operate. It can be used to provide up
to 500W of mains powered switching OR separate volts free switching for
circuits not requiring additional mains power. The relay latches between three
positions: switched live 1, switched live 2 and a neutral position (not connected).
IMPORTANT: The Inline relay is not designed to be left exposed once it is
installed, as live mains wiring is connected to the terminals. Ensure that the
device is mounted securely in a suitable housing. If conducting an insulation
resistance test, all LightwaveRF products must be disconnected from the
mains, or damage will occur.
230V Mains
power in
Switching terminals.
Volts free OR mains
Wiring terminals
Switched
live 1
Switched
live 2
Common Live Neutral
2. Connect the live and neutral
terminals, as shown in the diagram, to
provide power to the relay. When the
green LED is illuminated, the relay is
connected to mains power.
NOTE: Even if switching a low voltage or
non-mains circuit, the relay must always
have mains power connected to the live
and neutral terminals for it to be able to
function.
Installation
COM L N
L N
Live wire Neutral
wire
Connecting to a circuit volts free
Use this configuration to switch one or
two circuits that do not require mains
power to be provided from the live and
1. IMPORTANT: Turn o the mains electrical supply.
Relay terminals
Wiring the relay
COM L N
L N
1. Connect the incoming ‘live’ wire
from the low voltage circuit to the
common (com) terminal as shown in
the diagram.
Mains
power to
relay
Circuit live wire
Installation
COM L N
L N
On Position - circuit
connected
IMPORTANT: When the relay is operated remotely via RF, it is always the
lefthand load terminal that will be connected when the ‘on’ button is pressed.
Therefore, if the circuit is wired as shown, pressing ‘on’ using an RF remote
will turn on the circuit, and ‘o’ will disconnect it.
COM L N
L N
O Position - circuit
disconnected
2. Connect the outgoing wire ‘load’
to the leftmost load terminals ( )
as shown in the diagram. This is the
wire that will be collected to the ‘load’
(i.e. device to be switched or lamp).
The relay now has 2 positions - ‘on’
and ‘o’. The diagrams below show
the on and o positions if a live were
to be connected to the common and
load to the leftmost load terminal.
COM L N
L N
Mains power
to relay
Circuit
live wire
Circuit
switched
live (to
device)
Installation
COM L N
L N
COM L N
L N
Position 1 - circuit 1 connected
COM L N
L N
Position 2 - circuit 2 connected
Switching between two Circuits
If a second load wire connected to another circuit is attached to the second
switched live terminal (see diagram), the relay can be used to switch between
two circuits. In addition to the on and o positions, there is also a ‘stop’
position which breaks contact with both of the right and lefthand circuits.
COM L N
L N
Stop Position (no circuit connected)
Circuit
live wire
Circuit
switched
live 1 (to
device)
Circuit
switched
live 2 (to
device)
Installation
NOTE: A standard handheld or other LightwaveRF remote control will only
be able to utilise the ‘on’ and ‘o’ commands to switch between circuits but
NOT use the stop command, as it does not include this function.
To operate the stop command you will need a LightwaveRF ‘On/O/Stop
Switch’ which includes ‘on/o’ (open/close) and ‘stop’ commands OR the
LightwaveRF App (requires Lightwave Link).
If you are using the App, you must slect the device as ‘open/close’ during
linking process (see in-app help). This will give you the ‘stop’ command as
well as on/o (open/close) when you come to operate the device from the
smartphone.
Curtains, Blinds and Doors
Because of the ‘stop’ command feature, the relay can be used to operate a
device that requires an on/o (or open/close) function AND a stop (or
pause) function, such as blinds, curtains and doors.
In this case, as before, the incoming live wire will be connected to the ‘com’
terminal, and there will be two separate outgoing ‘load’ wires each
connected to the separate switched live (or load) terminals (see diagram on
the next page).
Installation
COM L N
L N
If the relay is being used to control
(interupt) a mains powered circuit
(max 500W load), then power
must be taken from the relay’s
main live terminal via a jumper
connection to the common
terminal (see diagram).
The neutral terminal must now also
accommodate an incoming and
outgoing connection to the mains
circuit.
COM L N
L N
NOTE: Because of the extra ‘stop’
command, a LightwaveRF ‘On
/o/stop Switch’ or the
LightwaveRF App and Lightwave
Link will be required to operate this
setup.
Connecting the Inline Relay to a circuit requiring mains power
Circuit
live wire
Circuit
switched
live 1 (to
device)
Circuit
switched
live 2 (to
device)
Circuit
live wire
Circuit
switched
live 1 (to
device)
Mains
neutral
Mains
live
Neutral
from
device
Inhaltsverzeichnis
Andere Lightwave Relais Handbücher
