Linak TECHLINE LA25 Gebrauchsanweisung
Actuator LA25
Endstop signals and absolute positioning - Analogue feedback
Connection diagram
LINAK.COM/TECHLINE
FOR MOUNTING INSTRUCTIONS AND GUIDANCE IN USAGE, PLEASE SEE THE RELEVANT USER’S MANUALS
Copyright © LINAK 2021.12 . MA-M9-02-603-C .LINAK A/S reserves the right to make technical alterations
Connection diagram
11
2019 © LINAK A/S
Endstop signals and absolute positioning - Analogue feedback
25XXXXXXXX0A0X0X=XXXXX1XXXXXXX
*YELLOW/GREEN: Endstop signals out are NOT potential free
Tip: If you wish to use the endstop signals, you will have to keep power on the red and black wires, otherwise the signal
will be lost.
Standard connector front view
DEUTSCH
8P
BROWN
BLUE
YELLOW*
GREEN*
RED
VIOLET
BLACK
+
-
2
1
3
4
7
8
6
Compliant with:
Powered by
Danfoss
FOR MOUNTING INSTRUCTIONS AND GUIDANCE IN USAGE, PLEASE SEE THE RELEVANT USER’S MANUALS
Copyright © LINAK 2021.12 . MA-M9-02-603-C .LINAK A/S reserves the right to make technical alterations
I/O Specifications
11
2019 © LINAK A/S
Endstop signals and absolute positioning - Analogue feedback
Input/Output Specification Comments
Description The actuator can be equipped with electronic circuit that gives an
analogue feedback signal, which indicates the position of actuator.
Brown 12-24 VDC (+/-)
12 V ± 20%
24 V ± 10%
Under normal conditions:
12V , 5 A at max load
24 V, 2.5 A at max load
To extend actuator:
Connect Brown to positive
To retract actuator:
Connect Brown to negative
Blue To extend actuator:
Connect Blue to negative
To retract actuator:
Connect Blue to positive
Red Signal power supply (+) 12-24 VDC Current consumption:
Max. 60 mA, also when the
actuator is not running
Black Signal power supply GND (-)
Green Endstop signal out Output voltage min. VIN - 2 V
Source current max. 100 mA
NOT potential free
Yellow Endstop signal in
Violet Analogue feedback
0-10 V (Feedback level 1)
0.5-4.5 V (Feedback level 2)
Tolerances +/- 0.2 V
Max. current output: 1 mA
Ripple max. 200 mV
Transaction delay max. 20 ms
Linear feedback 0.5%
Source current max. 1 mA
4-20 mA (Feedback level 3)
Special (Feedback level 9)
Tolerances +/- 0.2 mA
Transaction delay 20 ms
Linear feedback 0.5%
Output: Source
Serial resistance:
12V max 300 ohm
24V max. 900 ohm
White Not to be connected
For actuators with analogue feedback it is recommended to fully extract and retract the actuator on a regular basis (thereby activat-
ing the limit switches) in order to ensure precise positioning.
FOR MOUNTING INSTRUCTIONS AND GUIDANCE IN USAGE, PLEASE SEE THE RELEVANT USER’S MANUALS
Copyright © LINAK 2021.12 . MA-M9-02-603-C .LINAK A/S reserves the right to make technical alterations
Terms of use
The user is responsible for determining the suitability of LINAK products for specific application. LINAK takes great care in providing
accurate and up-to-date information on its products.
However, due to continuous development in order to improve its products, LINAK products are subject to frequent modifications and
changes without prior notice.Therefore, LINAK cannot guarantee the correct and actual status of said information on its products.
While LINAK uses its best efforts to fulfil orders, LINAK cannot, for the same reasons as mentioned above, guarantee the availability
of any particular product. Therefore, LINAK reserves the right to discontinue the sale of any product displayed on its website or listed
in its catalogues or other written material drawn up by LINAK.
All sales are subject to the Standard Terms of Sale and Delivery for LINAK. For a copy hereof, please contact LINAK.
Andere Linak Controller Handbücher
Linak
Linak TECHLINE LA36 Gebrauchsanweisung
Linak
Linak TECHLINE LA33 Bedienungsanleitung
Linak
Linak LA12 Bedienungsanleitung
Linak
Linak TECHLINE LA35 Bedienungsanleitung
Linak
Linak LA18 IC Advanced Bedienungsanleitung
Linak
Linak TD4 Bedienungsanleitung
Linak
Linak Homeline LA10 Bedienungsanleitung
Linak
Linak TD4 Bedienungsanleitung
Linak
Linak ACTUATOR LA36 Bedienungsanleitung
Linak
Linak HB100 Bedienungsanleitung
Linak
Linak MEDLINE LA32 Betriebshandbuch
Linak
Linak TECHLINE LA37 Bedienungsanleitung
Linak
Linak TWINDRIVE HB12 Bedienungsanleitung
Linak
Linak DL12 Bedienungsanleitung
Linak
Linak EM-322 Bedienungsanleitung
Linak
Linak BusLink LA25 Bedienungsanleitung
Linak
Linak ACTUATOR LA36 Bedienungsanleitung
Linak
Linak DESKLINE DL1A Bedienungsanleitung
Linak
Linak ACTUATOR LA36 Bedienungsanleitung
Linak
Linak TECHLINE LA25 Gebrauchsanweisung
