Lincoln Electric COBRAMATIC IM597 Bedienungsanleitung

Cobramatic®

For use with Push-Pull Torches Model K1589, K1590, K1591, K1592

World's Leader in Welding and Cutting Products

IM597

MK 091-0414

November 1999

Rev i

OPERATOR'S MANUAL

WIRE FEEDER

Safety Depends on You

Lincoln arc welding equipment is

designed and built with safety in

mind. However, your overall safety

can be increased by proper

installation...and thoughful operation

on your part. DO NOT INSTALL,

OPERATE OR REPAIR THIS

EQUIPMENT WITHOUT READING

THIS MANUAL AND THE SAFETY

PRECAUTIONS CONTAINED

THROUGHOUT. And, most

importantly, think before you act

and be careful.

Premier Manufacturer of Industrial Motors

Sales and Service through Subsidiaries and Distibutors Worldwide

Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com

OPERATOR'S MANUAL

K1587-1 Cobramatic® Owner's Manual -

Page 7

THIS PAGE INTENTIONALLY BLANK

K1587-1 Cobramatic® Owner's Manual -

Page 8

Table of Contents

Section 1 SPECIFICATIONS ........................................................... 10

Section 2 SUPPORT EQUIPMENT REQUIRED ................................ 10

Section 3 COOLANT RECOMMENDATIONS .................................... 10

Section 4 OPTIONAL ACCESSORIES .............................................. 10

Section 5 INSTALLATION .............................................................. 10

5.1 Location ................................................................................................. 10

5.2 42 VAC Input Power Connections ............................................................. 11

5.3 Posa Start Connection ............................................................................. 11

Section 6 WIRE THREADING PROCEDURE .................................... 11

6.1 Wire Spool Installation ............................................................................ 11

6.2 Threading Procedure ............................................................................... 11

6.3 Pre-Setting Slave Motor Tension ............................................................... 12

Section 7 OPERATION ................................................................... 12

7.1 General .................................................................................................. 12

7.2 Feeder Controls ...................................................................................... 12

7.3 CV/CC Posa Start Operating Procedure .................................................... 13

Section 8 MAINTENANCE............................................................... 14

8.1 Testing the Torch .................................................................................... 14

8.2 Relay K2 Operation ................................................................................. 15

8.3 Testing the Input Power Circuits ............................................................... 15

8.4 Testing the Speed Control ........................................................................ 15

MAIN PC BOARD CONNECTIONS ................................... 16

TROUBLE SHOOTING ..................................................... 17

DRAWINGS .................................................................... 18

K1587-1 Wire Feed Cabinet - Exploded View ............................................. 18

003-2016 Front Panel - Exploded View ...................................................... 20

003-0570 Spindle Brake Assembly - Exploded View .................................... 21

003-1232 Slave Motor Assembly - Exploded View ...................................... 22

Wire Harness for Input Power from Power Source ...................................... 23

Main PC Board Parts Placement................................................................ 24

Front Panel Circuit Board ......................................................................... 26

SCHEMATICS.................................................................. 27

Wiring Schematic .................................................................................... 27

Torch Connections .................................................................................. 28

Block Diagram ........................................................................................ 29

WARRANTY REPAIR STATIONS ..................................... 30

K1587-1 Cobramatic® Owner's Manual -

Page 9

THIS PAGE INTENTIONALLY BLANK

K1587-1 Cobramatic® Owner's Manual -

Page 10

Section 1 SPECIFICATIONS

Wire Diameter Capacity .................................... .030 - 1/16" ALL Types

Wire Capacity .................................................... 12" Standard

(Insulated or Non-Insulated)

Power Input ....................................................... 42 VAC 50/60 Hz,

............................................................................ 150 Watts Peak (3 amps)

Weight ................................................................ 31 pounds

Shipping Weight ............................................... 36 pounds

For Use with these Lincoln Torches ............... K1589,K1590,K1591,K1592

Section 2 SUPPORT EQUIPMENT REQUIRED

C.V. or C.C. Power Source of Sufficient Capacity for Your Needs.

Regulated Gas Supply and Hoses.

Properly Sized Power Leads from Power Source to Wire Feeder and Ground.

Water Source and Hose Capable of Providing a Minimum of 1 qt/min. at 45

p.s.i. when using water cooled torches.

Section 3 COOLANT RECOMMENDATIONS

1. Use a name-brand additive which does not contain reactive sulphur or

chlorine and does not react with copper, brass, or aluminum.

2. Check coolant periodically to remain within limits of the following:

A. Coolant Flow rate - 1 quart/minute at 45 p.s.i.

B. Resistivity - 10K ohms/centimeter

C. Ph Range - 5.5-8.5

D. Particle Size - .005"

Section 4 OPTIONAL ACCESSORIES

Replacement Plastic Guides for Slave Motor

Lincoln MK Products

Inlet Guide S23980-1 753-0062

Outlet Guide with Knob S23980-2 003-0428

Section 5 INSTALLATION

5.1 LOCATION

The cabinet should be placed in a location where it can be protected from

damage. Lead lengths and accessibility must also be considered when

installing the cabinet.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lincoln Electric Schweißsystem Handbücher

Lincoln Electric

Lincoln Electric EAGLE 10,000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric PRO-CUT 25 Bedienungsanleitung

Lincoln Electric

Lincoln Electric BESTER 130i-S Bedienungsanleitung

Lincoln Electric

Lincoln Electric IDEALARC CV-305 Bedienungsanleitung

Lincoln Electric

Lincoln Electric IDEALARC IM318-B Bedienungsanleitung

Lincoln Electric

Lincoln Electric SAE-400 SEVERE DUTY IM727 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V160-S Bedienungsanleitung

Lincoln Electric

Lincoln Electric Precision TIG 225 Bedienungsanleitung

Lincoln Electric

Lincoln Electric 12486 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE S350 Bedienungsanleitung

Lincoln Electric

Lincoln Electric power wave ac/dc 1000 sd Bedienungsanleitung

Lincoln Electric

Lincoln Electric Idealarc DC-600 Bedienungsanleitung

Lincoln Electric

Lincoln Electric FlexCut 80 CCC Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC STT Series Bedienungsanleitung

Lincoln Electric

Lincoln Electric PIPELINER IM769 Bedienungsanleitung

Lincoln Electric

Lincoln Electric TOMAHAWK 375 AIR Bedienungsanleitung

Lincoln Electric

Lincoln Electric RED-D-ARC ES 275I Bedienungsanleitung

Lincoln Electric

Lincoln Electric Idealarc R3R-400 Bedienungsanleitung

Lincoln Electric

Lincoln Electric IM869-D Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER MIG IM736-D Bedienungsanleitung

Lincoln Electric

Lincoln Electric SQUARE WAVE IM565-B Bedienungsanleitung

Lincoln Electric

Lincoln Electric BIG RED IM10019 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE S350 Bedienungsanleitung

Lincoln Electric

Lincoln Electric PRECISION TIG SVM186-A Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Everlast

Everlast POWER MTS 221STi Bedienungsanleitung

Kipor

Kipor KDE180XW Bedienungsanleitung