Lincoln Electric EAGLETM 10 Bedienungsanleitung

EAGLE™10,000 PLUS

$%')$'X("#*!

Fo Machines with Code Numbe 11618,11735, 11791, 11798

"

Feb ua y, 2011

(165DI5@5>4C?>.?E

Lincoln arc welding and cutting

equipment is designed and built

with safety in mind. However,

your overall safety can be

increased by proper installation

... and thoughtful operation on

your part. $#$)#()!!

$%')$''%')(

&*%"#),)$*)'

#)("#*!#)

().%'*)$#($#

)#)'$*$*) And,

most importantly, think before

you act and be careful.

• Sales and Service through Subsidiaries and istributors Worldwide •

Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com

• World's Leader in Welding and Cutting Products •

Copy ight © Lincoln Global Inc.

$'##

@?G5B545AE9@=5>D

1.a. Turn the engine off before troubleshooting and maintenance

work unless the maintenance work requires it to be running.

____________________________________________________

1.b. Operate engines in open, well-ventilated

areas or vent the engine exhaust fumes

outdoors.

____________________________________________________

1.c. o not add the fuel near an open flame

welding arc or when the engine is running.

Stop the engine and allow it to cool before

refueling to prevent spilled fuel from vaporiz-

ing on contact with hot engine parts and

igniting. o not spill fuel when filling tank. If

fuel is spilled, wipe it up and do not start

engine until fumes have been eliminated.

____________________________________________________

1.d. Keep all equipment safety guards, covers and devices in

position and in good repair.Keep hands, hair, clothing and

tools away from V-belts, gears, fans and all other moving

parts when starting, operating or repairing equipment.

____________________________________________________

1.e. In some cases it may be necessary to remove safety

guards to perform required maintenance. Remove

guards only when necessary and replace them when the

maintenance requiring their removal is complete.

Always use the greatest care when working near moving

parts.

___________________________________________________

1.f. o not put your hands near the engine fan.

o not attempt to override the governor or

idler by pushing on the throttle control rods

while the engine is running.

___________________________________________________

1.g. To prevent accidentally starting gasoline engines while

turning the engine or welding generator during maintenance

work, disconnect the spark plug wires, distributor cap or

magneto wire as appropriate.

().

',!##/'$*( %'$)).$*'(!#$)'('$"%$((!('$*(#*'.$')

%!'#,.%" ',''(($*!$#(*!),))'$)$'$'$%')#

Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you

purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box

351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available

from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

(*' )) !! #()!!)$#$%')$# "#)## # '%'%'$*'( '

%'$'"$#!..&*!#+*!(

,'##

!)'#

"#)!(

=1I2541>75B?EC

2.a. Electric current flowing through any conductor causes

localized Electric and Magnetic Fields (EMF). Welding

current creates EMF fields around welding cables and

welding machines

2.b. EMF fields may interfere with some pacemakers, and

welders having a pacemaker should consult their physician

before welding.

2.c. Exposure to EMF fields in welding may have other health

effects which are now not known.

2.d. All welders should use the following procedures in order to

minimize exposure to EMF fields from the welding circuit:

2.d.1.

Route the electrode and work cables together - Secure

them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. o not place your body between the electrode and

work cables. If the electrode cable is on your right

side, the work cable should also be on your right side.

2.d.4. Connect the work cable to the workpiece as close as

possible to the area being welded.

2.d.5. o not work next to welding power source.

1.h. To avoid scalding, do not remove the

radiator pressure cap when the engine is

hot.

!$'#%'$%$()$#,'##(

iesel engine exhaust and some of its constituents

are known to the State of California to cause can-

cer, birth defects, and other reproductive harm.

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

The Above For iesel Engines The Above For Gasoline Engines

ARC RAYS an burn.

4.a. Use a shield with the proper filter and cover

plates to protect your eyes from sparks and

the rays of the arc when welding or observing

open arc welding. Headshield and filter lens

should conform to A SI Z87. I standards.

4.b. Use suitable clothing made from durable flame-resistant

material to protect your skin and that of your helpers from

the arc rays.

4.c. Protect other nearby personnel with suitable, non-flammable

screening and/or warn them not to watch the arc nor expose

themselves to the arc rays or to hot spatter or metal.

ELECTRIC SHOCK an

kill.

3.a. The electrode and work (or ground) circuits

are electrically “hot” when the welder is on.

Do not touch these “hot” parts with your bare

skin or wet clothing. Wear dry, hole-free

gloves to insulate hands.

3.b. Insulate yourself from work and ground using dry insulation.

Make certain the insulation is large enough to cover your full

area of physical contact with work and ground.

In addition to the normal safety pre autions, if welding

must be performed under ele tri ally hazardous

onditions (in damp lo ations or while wearing wet

lothing; on metal stru tures su h as floors, gratings or

s affolds; when in ramped positions su h as sitting,

kneeling or lying, if there is a high risk of unavoidable or

a idental onta t with the workpie e or ground) use

the following equipment:

• Semiautomati DC Constant Voltage (Wire) Welder.

• DC Manual (Sti k) Welder.

• AC Welder with Redu ed Voltage Control.

3.c. In semiautomatic or automatic wire welding, the electrode,

electrode reel, welding head, nozzle or semiautomatic

welding gun are also electrically “hot”.

3.d. Always be sure the work cable makes a good electrical

connection with the metal being welded. The connection

should be as close as possible to the area being welded.

3.e. Ground the work or metal to be welded to a good electrical

(earth) ground.

3.f.

Maintain the electrode holder, work clamp, welding cable and

welding machine in good, safe operating condition. Replace

damaged insulation.

3.g. ever dip the electrode in water for cooling.

3.h. ever simultaneously touch electrically “hot” parts of

electrode holders connected to two welders because voltage

between the two can be the total of the open circuit voltage

of both welders.

3.i. When working above floor level, use a safety belt to protect

yourself from a fall should you get a shock.

3.j. Also see Items 6.c. and 8.

SAFETY

FUMES AND GASES

an be dangerous.

5.a. Welding may produce fumes and gases

hazardous to health. Avoid breathing these

fumes and gases. When welding, keep

your head out of the fume. Use enough

ventilation and/or exhaust at the arc to keep

fumes and gases away from the breathing zone. When

welding with ele trodes whi h require spe ial

ventilation su h as stainless or hard fa ing (see

instru tions on ontainer or MSDS) or on lead or

admium plated steel and other metals or oatings

whi h produ e highly toxi fumes, keep exposure as

low as possible and within appli able OSHA PEL and

ACGIH TLV limits using lo al exhaust or me hani al

ventilation. In onfined spa es or in some ir um-

stan es, outdoors, a respirator may be required.

Additional pre autions are also required when welding

on galvanized steel.

5. b. The operation of welding fume control equipment is affected

by various factors including proper use and positioning of

the equipment, maintenance of the equipment and the spe-

cific welding procedure and application involved. Worker

exposure level should be checked upon installation and

periodically thereafter to be certain it is within applicable

OSHA PEL and ACGIH TLV limits.

5.c.

Do not weld in locations near chlorinated hydrocarbon

vapors

coming from degreasing, cleaning or spraying operations.

The heat and rays of the arc can react with solvent vapors

form phosgene, a highly toxic gas, and other irritating prod-

ucts.

5.d. Shielding gases used for arc welding can displace air and

cause injury or death. Always use enough ventilation,

especially in confined areas, to insure breathing air is safe.

5.e. Read and understand the manufacturer’s instructions for this

equipment and the consumables to be used, including the

material safety data sheet (MSDS) and follow your

employer’s safety practices. MSDS forms are available from

your welding distributor or from the manufacturer.

5.f. Also see item 1.b.

FOR ELECTRICALLY

powered equipment.

8.a. Turn off input power using the disconnect

switch at the fuse box before working on

the equipment.

8.b. Install equipment in accordance with the U.S. ational

Electrical Code, all local codes and the manufacturer’s

recommendations.

8.c. Ground the equipment in accordance with the U.S. ational

Electrical Code and the manufacturer’s recommendations.

CYLINDER may explode

if damaged.

7.a. Use only compressed gas cylinders

containing the correct shielding gas for the

process used and properly operating

regulators designed for the gas and

pressure used. All hoses, fittings, etc. should be suitable for

the application and maintained in good condition.

7.b. Always keep cylinders in an upright position securely

chained to an undercarriage or fixed support.

7.c. Cylinders should be located:

• Away from areas where they may be struck or subjected to

physical damage.

• A safe distance from arc welding or cutting operations and

any other source of heat, sparks, or flame.

7.d. ever allow the electrode, electrode holder or any other

electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet

when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand

tight except when the cylinder is in use or connected for

use.

7.g. Read and follow the instructions on compressed gas

cylinders, associated equipment, and CGA publication P-l,

“Precautions for Safe Handling of Compressed Gases in

Cylinders,” available from the Compressed Gas Association

1235 Jefferson Davis Highway, Arlington, VA 22202.

WELDING and CUTTING

SPARKS an

ause fire or explosion.

6.a.

Remove fire hazards from the welding area.

If this is not possible, cover them to prevent

the welding sparks from starting a fire.

Remember that welding sparks and hot

materials from welding can easily go through small cracks

and openings to adjacent areas. Avoid welding near

hydraulic lines. Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site,

special precautions should be used to prevent hazardous

situations. Refer to “Safety in Welding and Cutting” (A SI

Standard Z49.1) and the operating information for the

equipment being used.

6.c. When not welding, make certain no part of the electrode

circuit is touching the work or ground. Accidental contact

can cause overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the

proper steps have been taken to insure that such procedures

will not cause flammable or toxic vapors from substances

inside. They can cause an explosion even

though

they have

been “cleaned”. For information, purchase “Recommended

Safe Practices for the

Preparation

for Welding and Cutting of

Containers and Piping That Have Held Hazardous

Substances”, AWS F4.1 from the American Welding Society

(see address above).

6.e. Vent hollow castings or containers before heating, cutting or

welding. They may explode.

6.f.

Sparks and spatter are thrown from the welding arc. Wear oil

free protective garments such as leather gloves, heavy shirt,

cuffless trousers, high shoes and a cap over your hair. Wear

ear plugs when welding out of position or in confined places.

Always wear safety glasses with side shields when in a

welding area.

6.g. Connect the work cable to the work as close to the welding

area as practical. Work cables connected to the building

framework or other locations away from the welding area

increase the possibility of the welding current passing

through lifting chains, crane cables or other alternate cir-

cuits. This can create fire hazards or overheat lifting chains

or cables until they fail.

6.h. Also see item 1.c.

6.I. Read and follow FPA 51B “ Standard for Fire Prevention

During Welding, Cutting and Other Hot Work”, available

from FPA, 1 Batterymarch Park, PO box 9101, Quincy, Ma

022690-9101.

6.j. Do not use a welding power source for pipe thawing.

iii

SAFETY

iii

Refer to http://www.lin olnele tri . om/safety for additional safety information.

().

%'L*)$#((V')L

Pour votre propre protection lire et observer toutes les instructions

et les précautions de sûreté specifiques qui parraissent dans ce

manuel aussi bien que les précautions de sûreté générales suiv-

antes:

(NB5DM%?EB(?E4175!XB3

1. Protegez-vous contre la secousse électrique:

a. Les circuits à l’électrode et à la piéce sont sous tension

quand la machine à souder est en marche. Eviter toujours

tout contact entre les parties sous tension et la peau nue

ou les vétements mouillés. Porter des gants secs et sans

trous pour isoler les mains.

b. Faire trés attention de bien s’isoler de la masse quand on

soude dans des endroits humides, ou sur un plancher

metallique ou des grilles metalliques, principalement dans

les positions assis ou couché pour lesquelles une grande

partie du corps peut être en contact avec la masse.

c. Maintenir le porte-électrode, la pince de masse, le câble

de soudage et la machine à souder en bon et sûr état

defonctionnement.

d.Ne jamais plonger le porte-électrode dans l’eau pour le

refroidir.

e. Ne jamais toucher simultanément les parties sous tension

des porte-électrodes connectés à deux machines à souder

parce que la tension entre les deux pinces peut être le

total de la tension à vide des deux machines.

f. Si on utilise la machine à souder comme une source de

courant pour soudage semi-automatique, ces precautions

pour le porte-électrode s’applicuent aussi au pistolet de

soudage.

2. ans le cas de travail au dessus du niveau du sol, se protéger

contre les chutes dans le cas ou on recoit un choc. Ne jamais

enrouler le câble-électrode autour de n’importe quelle partie

du corps.

3. Un coup d’arc peut être plus sévère qu’un coup de soliel,

donc:

a. Utiliser un bon masque avec un verre filtrant approprié

ainsi qu’un verre blanc afin de se protéger les yeux du ray-

onnement de l’arc et des projections quand on soude ou

quand on regarde l’arc.

b. Porter des vêtements convenables afin de protéger la

peau de soudeur et des aides contre le rayonnement de

l‘arc.

c. Protéger l’autre personnel travaillant à proximité au

soudage à l’aide d’écrans appropriés et non-inflammables.

4. es gouttes de laitier en fusion sont émises de l’arc de

soudage. Se protéger avec des vêtements de protection libres

de l’huile, tels que les gants en cuir, chemise épaisse, pan-

talons sans revers, et chaussures montantes.

5. Toujours porter des lunettes de sécurité dans la zone de

soudage. Utiliser des lunettes avec écrans lateraux dans les

zones où l’on pique le laitier.

6. Eloigner les matériaux inflammables ou les recouvrir afin de

prévenir tout risque d’incendie dû aux étincelles.

7. Quand on ne soude pas, poser la pince à une endroit isolé de

la masse. Un court-circuit accidental peut provoquer un

échauffement et un risque d’incendie.

8. S’assurer que la masse est connectée le plus prés possible

de la zone de travail qu’il est pratique de le faire. Si on place

la masse sur la charpente de la construction ou d’autres

endroits éloignés de la zone de travail, on augmente le risque

de voir passer le courant de soudage par les chaines de lev-

age, câbles de grue, ou autres circuits. Cela peut provoquer

des risques d’incendie ou d’echauffement des chaines et des

câbles jusqu’à ce qu’ils se rompent.

9. Assurer une ventilation suffisante dans la zone de soudage.

Ceci est particuliérement important pour le soudage de tôles

galvanisées plombées, ou cadmiées ou tout autre métal qui

produit des fumeés toxiques.

10. Ne pas souder en présence de vapeurs de chlore provenant

d’opérations de dégraissage, nettoyage ou pistolage. La

chaleur ou les rayons de l’arc peuvent réagir avec les vapeurs

du solvant pour produire du phosgéne (gas fortement toxique)

ou autres produits irritants.

11. Pour obtenir de plus amples renseignements sur la sûreté,

voir le code “Code for safety in welding and cutting” CSA

Standard W 117.2-1974.

%'L*)$#((V')L%$*'

!("#(R($*'R

)'#($'")*')R

''((*'

1. Relier à la terre le chassis du poste conformement au code de

l’électricité et aux recommendations du fabricant. Le dispositif

de montage ou la piece à souder doit être branché à une

bonne mise à la terre.

2. Autant que possible, I’installation et l’entretien du poste seront

effectués par un électricien qualifié.

3. Avant de faires des travaux à l’interieur de poste, la debranch-

er à l’interrupteur à la boite de fusibles.

4. Garder tous les couvercles et dispositifs de sûreté à leur

place.

Thank You for selecting a &*!). product by Lincoln Electric. We want you

to take pride in operating this Lincoln Electric Company product

••• as much pride as we have in bringing this product to you!

'514D89C$@5B1D?BC"1>E1<3?=@<5D5<I before attempting to use this equipment. Save this manual and keep it

handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.

The level of seriousness to be applied to each is explained below:

,'##

This statement appears where the information =ECD be followed 5H13D<I to avoid C5B9?EC@5BC?>1<9>:EBI or <?CC?6<965.

This statement appears where the information =ECD be followed to avoid =9>?B@5BC?>1<9>:EBI or 41=175D?D89C5AE9@=5>D.

*)$#

%<51C5 H1=9>5 1BD?> 1>4 AE9@=5>D ?B 1=175 ==5491D5<I

When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims

for material damaged in shipment must be made by the purchaser against the transportation company at the

time the shipment is received.

Please record your equipment identification information below for future reference. This information can be

found on your machine nameplate.

Product _________________________________________________________________________________

Model Number ___________________________________________________________________________

Code Number or ate Code_________________________________________________________________

Serial Number____________________________________________________________________________

ate Purchased___________________________________________________________________________

Where Purchased_________________________________________________________________________

Whenever you request replacement parts or information on this equipment, always supply the information you

have recorded above. The code number is especially important when identifying the correct replacement parts.

$>!9>5 %B?4E3D '579CDB1D9?>

- Register your machine with Lincoln Electric either via fax or over the Internet.

• For faxing: Complete the form on the back of the warranty statement included in the literature packet

accompanying this machine and fax the form per the instructions printed on it.

• For On-Line Registration: Go to our

,W()1DGGG<9>3?<>5<53DB933?=Choose “Quick Links” and then

“Product Registration”. Please complete the form and submit your registration.

*()$"'((()#%$!.

The business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equip-

ment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask Lincoln

Electric for advice or information about their use of our products. We respond to our customers based on the best information in our posses-

sion at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such infor-

mation or advice. We expressly disclaim any warranty of any kind, including any warranty of fitness for any customer’s particular purpose,

with respect to such information or advice. As a matter of practical consideration, we also cannot assume any responsibility for updating or

correcting any such information or advice once it has been given, nor does the provision of information or advice create, expand or alter any

warranty with respect to the sale of our products.

Lincoln Electric is a responsive manufacturer, but the selection and use of specific products sold by Lincoln Electric is solely within the control

of, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric affect the results obtained in

applying these types of fabrication methods and service requirements.

Subject to Change – This information is accurate to the best of our knowledge at the time of printing. Please refer to www.lincolnelectric.com

for any updated information.

F9

F9 )!$$#)#)(

Page

>CD1<<1D9?>(53D9?>

Technical Specifications.......................................................................................................A-1

Safety Precautions ........................................................................................................A-2

Machine Grounding.......................................................................................................A-2

Spark Arrester ...............................................................................................................A-2

Towing...........................................................................................................................A-2

Vehicle Mounting...........................................................................................................A-3

Pre-Operation Engine Service..............................................................................................A-3

Fuel, Oil, Battery Connections ......................................................................................A-3

Welding Cable Connections..........................................................................................A-4

Angle of Operation ........................................................................................................A-4

Lifting, Additional Safety Precautions............................................................................A-4

High Altitude Operation .................................................................................................A-4

Muffler Outlet Pipe ........................................................................................................A-4

Location and Ventilation................................................................................................A-5

Stacking ........................................................................................................................A-5

Connection of Tig Module .............................................................................................A-5

Additional Safety Precautions .......................................................................................A-5

Welding Operation Output, Auxiliary Power Receptacles, and Plugs .................................A-6

Motor Starting and Extension Cord Length Table ................................................................A-6

Electrical evice Used with the EAGLE™ 10,000 Plus .......................................................A-7

Auxiliary Power While Welding, Standby Power Connections ............................................A-8

Premises Wiring ...................................................................................................................A-9

________________________________________________________________________________

$@5B1D9?>(53D9?>

Safety Precautions ...............................................................................................................B-1

General escription..............................................................................................................B-1

Welder Controls Function and Operation .............................................................................B-1

Range, Polarity Control Switch and Fuel Consumption .......................................................B-2

Start in/Shutdown Instructions.....................................................................................................B-3

Starting the Engine........................................................................................................B-3

Safety Precautions ........................................................................................................B-3

Stopping the Engine......................................................................................................B-3

Break-In Period .............................................................................................................B-3

Welding Process ..................................................................................................................B-4

Stick (Constant Current) Welding..................................................................................B-4

Scratch Start TIG (Constant Current) Welding .............................................................B-4

Arc Gouging ..................................................................................................................B-5

Summary of Welding Processes ...................................................................................B-5

________________________________________________________________________________

335CC?B95C (53D9?>

Optional Equipment...............................................................................................C-1

Recommended Equipment....................................................................................C-2

________________________________________________________________________

"19>D5>1>35 (53D9?>

Safety Precautions ................................................................................................ -1

Routine Engine Maintenance .......................................................................... -1, 2

Engine Adjustments............................................................................................... -3

Slip Rings .............................................................................................................. -3

Battery Maintenance ....................................................................................... -3

Engine Maintenance Parts.............................................................................. -3

________________________________________________________________________

)B?E2<5C8??D9>7(53D9?>

How to Use Troubleshooting Guide.......................................................................E-1

Troubleshooting Guide...................................................................................E-2, E-3

________________________________________________________________________

,9B9>7917B1=9=5>C9?>%B9>D(53D9?>

Wiring iagram F-1

imension Print......................................................................................................F-2

000000000000000000000000000000000000000000000000000000000000000000000000

%1BDC!9CD%

000000000000000000000000000000000000000000000000000000000000000000000000



#()!!)$#

!Q%!*(



)#!(%)$#(!Q%<EC 

#%*)($!###

')$*)%*)OO,!'

')$*)%*)OO#')$'

,5<49>7$ED@ED

C Constant Current 225A / 25V / 40%

C Constant Current 210A / 25V / 100%

EH9<91BI%?G5B

9,000 Watts Continuous, 60 Hz AC

10,500 Watts Surge, 60 Hz AC

120/240 Volts

"1;5"?45<

Kohler

CH23S

5C3B9@D9?>

2 cylinder

4 Cycle

Air-Cooled

Gasoline

Engine.

Aluminum Alloy

with Cast Iron

Liners,

Electronic

Ignition

$@5B1D9>7

(@554'%"

High Idle 3700

Full Load 3500

Low Idle 2200

9C@<135=5>D

3E9>

3E3=

41.1(674)

1@139D95C

Fuel:

12 Gal (45.4 L)

Lubricating Oil:

2.0 Qts. (1.9 L)

?BC5@?G5B

23 HP @

3600 RPM

(D1BD9>7

(ICD5=

12V C

Battery

Electric Start

Group 58

Battery

(435 cold

Cranking

Amps)

Output rating in watts is equivalent to volt - amperes at unity factor.Output voltage is within +/-10% at all loads up to rated capacity.

When welding available auxiliary power will be reduced.

'%)!(

(2) 120VAC uplex (5-20R)

(1) 120/240VAC ual Voltage

Full KVA (14-50R)

))'.'# '*)' '

20AMP for Engine Battery

Charging Circuit

*-!'.%$,''*)' '

Two 20AMP for Two uplex Receptacle

(1) 40AMP for ual Voltage (2-pole)

'%)!(#'*)' '(

) ,) %) ,)

30.00** in. 21.50 in 42.25 in.

762.0 mm 546.0 mm 1073.0 mm

!*')$# +!+!)'( *!(.()" $+'#$'

Full Pressure Hydraulic Mechanical Fuel Pump Mechanical Governor

with Full Flow Filter

5% Regulation

'!#' ##!' "*!' ##%'$))$#

Low noise Muffler: Top outlet Shutdown on low oil

ual Element Automatic Idler can be rotated. Made from pressure.

long life, aluminized steel.

%.(!"#($#(

##$"%$##)(

** Top of enclosure, add 6.00”(152mm) for exhaust.

514 lbs. (233kg)



#()!!)$#

!Q%!*(



().%'*)$#(

"#'$*##

Because this portable engine driven welder or genera-

tor creates it’s own power, it is not necessary to con-

nect it’s frame to an earth ground, unless the machine

is connected to premises wiring (your home, shop,

etc.).

)?@B5F5>D41>75B?EC5<53DB93C8?3;?D85B5AE9@

=5>DD?G8938D89C5>79>54B9F5>G5<45BCE@@<95C

@?G5B=ECD

•257B?E>454D?D856B1=5?6D85G5<45BEC9>71

7B?E>454DI@5@<E7 ?B 254?E2<59>CE<1D54

?>?D7B?E>4D85=1389>5D?1@9@5D81D31BB95C

5H@<?C9F5?B3?=2ECD92<5=1D5B91<

------------------------------------------------------------------------

When this welder is mounted on a truck or trailer, it’s

frame must be electrically bonded to the metal frame

of the vehicle. Use a #8 or larger copper wire connect-

ed between the machine grounding stud and the

frame of the vehicle.

Where this engine driven welder is connected to

premises wiring such as that in your home or shop, it’s

frame must be connected to the system earth ground.

See further connection instructions in the section enti-

tled “Standby Power Connections”, as well as the arti-

cle on grounding in the latest National Electrical Code

and the local code.

In general, if the machine is to be grounded, it should

be connected with a #8 or larger copper wire to a solid

earth ground such as a metal water pipe going into

the ground for at least ten feet and having no insulat-

ed joints, or to the metal framework of a building

which has been effectively grounded. The National

Electrical Code lists a number of alternate means of

grounding electrical equipment. A machine grounding

stud marked with the symbol is provided on the

front of the welder.

(%' ''()'

Some federal, state, or local laws may require that

gasoline engines be equipped with exhaust spark

arresters when they are operated in certain locations

where unarrested sparks may present a fire hazard.

The standard muffler included with this welder does

not qualify as a spark arrester. When required by local

regulations, the K1898-1 spark arrester must be

installed and properly maintained.

>9>3?BB53D1BB5CD5B =1I <514 D? 41=175 D? D85

5>79>5?B14F5BC5<I16653D@5B6?B=1>35

------------------------------------------------------------------------

)$,#

The recommended trailer for use with this equipment

for road, in-plant and yard towing by a vehicle(1) is

Lincoln’s K2635-1. If the user adapts a non-Lincoln

trailer, he must assume responsibility that the method

of attachment and usage does not result in a safety

hazard nor damage the welding equipment. Some of

the factors to be considered are as follows:

1. esign capacity of trailer vs. weight of Lincoln

equipment and likely additional attachments.

2. Proper support of, and attachment to, the base of

the welding equipment so there will be no undue

stress to the framework.

*)$#

?>?D1DD5=@DD?EC5D89C5AE9@=5>DE>D9<I?E

81F5D8?B?E78<I B514 D855>79>5=1>E613DEB5BXC

=1>E1<CE@@<954G9D8I?EBG5<45BD9>3<E45C

9=@?BD1>DC165DI@B531ED9?>C45D19<545>79>5

CD1BD9>7?@5B1D9>71>4 =19>D5>1>35 9>CDBE3D9?>C

1>4@1BDC<9CDC



!)'($ 31>;9<<

P?>?DD?E385<53DB931<<I<9F5@1BDC?B

5<53DB?45G9D8C;9>?BG5D3<?D89>7

P>CE<1D5I?EBC5<66B?=G?B;1>4

7B?E>4

P<G1ICG51B4BI9>CE<1D9>77<?F5C

##W-*()W31>;9<<

P*C59>?@5>G5<<F5>D9<1D541B51C?B

F5>D5H81ECD?EDC945

"$+#%')(W31>9>:EB5

P?>?D?@5B1D5G9D84??BC?@5>?B

7E1B4C?66

P(D?@5>79>5256?B5C5BF939>7

P 55@1G1I6B?==?F9>7@1BDC

(551449D9?>1<G1B>9>79>6?B=1D9?>1D

6B?>D?6D89C?@5B1D?BXC=1>E1<



,'##

*!

Fill the fuel tank with clean, fresh, lead-free gasoline.

Observe fuel sight gauge in the base of the machine

while filling to prevent overfilling.

$!

The EAGLE™ 10,000 Plus is shipped with the engine

crankcase filled with SAE 10W-30 oil. Check the oil

level before starting the engine. If it is not up to the full

mark on the dip stick, add oil as required. Make cer-

tain that the oil filler cap is tightened securely. Refer to

the engine Owner’s Manual for specific oil recommen-

dations.

))'.$##)$#(

*C531ED9?>1CD855<53DB?<ID59C1CDB?>7

1394D81D31>2EB>C;9>1>441=1755I5C

------------------------------------------------------------------------

This welder is shipped with the negative battery cable

disconnected. Make sure that the Engine Switch is in

the “STOP” position and attach the disconnected

cable securely to the negative battery terminal before

attempting to operate the machine. If the battery is

discharged and does not have enough power to start

the engine, see the battery charging instructions in the

Battery section.

#$): This machine is furnished with a wet charged

battery; if unused for several months, the battery may

require a booster charge. Be careful to charge the bat-

tery with the correct polarity.

3. Proper placement of the equipment on the trailer to

insure stability side to side and front to back when

being moved and when standing by itself while

being operated or serviced.

4. Typical conditions of use, i.e., travel speed; rough-

ness of surface on which the trailer will be operated;

environmental conditions.

5. Conformance with federal, state and local laws(1)

(1) Consult applicable federal, state and local laws regarding specific

requirements for use on public highways.



#()!!)$#

!Q%!*(



%'$%')$#('+

'D855>79>5?@5B1D9>71>4=19>D5>1>35

9>CDBE3D9?>CCE@@<954G9D8D89C=1389>5

*)$#

LUBRICATION SYSTEM CAPACITY

(INCLU ING FILTER)

Kohler CH23S - 2.0 Quarts (1.9 Liters)

P1=175D?D856E5<D1>;=1I31EC5

69B5?B5H@<?C9?>?>?D 4B9<<8?<5C

9>D85!Q%<EC21C5?B

G5<4D?D85!Q%<EC

21C5

-----------------------------------------------------------------------

,'##

*)$#

P(D?@5>79>5G89<56E5<9>7

P?>?DC=?;5G85>6E5<9>7

P 55@C@1B;C1>46<1=51G1I6B?=

D1>;

P?>?D<51F5E>1DD5>454G89<5

6E5<9>7

P,9@5E@C@9<<546E5<1>41<<?G

6E=5CD?3<51B256?B5CD1BD9>7

5>79>5

P?>?D?F5B69<<D1>;6E5<5H@1>

C9?>=1I31EC5?F5B6<?G

($!#*!$#!.

------------------------------------------------------------------------

,'##

($!#

31>31EC569B5

?B5H@<?C9?>

+!"$*#)#

=@B?@5B<I=?E>D543?>35>DB1D54<?14C=1I

31EC5E>CD12<5F5893<581>4<9>71>4D9B5C?B?D85B

3?=@?>5>DCD?619<

P$><IDB1>C@?BDD89CAE9@=5>D?>C5BF93512<5

F5893<5CG89381B5B1D541>445C97>546?BCE38

<?14C

P9CDB92ED521<1>351>4C53EB5<?14CC?F5893<5

9CCD12<5E>45B3?>49D9?>C?6EC5

P?>?D5H3554=1H9=E=B1D54<?14C6?B3?=@?

>5>DCCE381CCEC@5>C9?>1H<5C1>4D9B5C

P"?E>D5AE9@=5>D21C5D?=5D1<254?B6B1=5?6

F5893<5

P?<<?GF5893<5=1>E613DEB5BXC9>CDBE3D9?>C

------------------------------------------------------------------------

,'##

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lincoln Electric Schweißsystem Handbücher

Lincoln Electric

Lincoln Electric OUTBACK SVM204-A Bedienungsanleitung

Lincoln Electric

Lincoln Electric Flextec 650x Bedienungsanleitung

Lincoln Electric

Lincoln Electric IDEALARC CV-400-I Bedienungsanleitung

Lincoln Electric

Lincoln Electric MARQUETTE AUTOPRO 20 Bedienungsanleitung

Lincoln Electric

Lincoln Electric S350 CE Bedienungsanleitung

Lincoln Electric

Lincoln Electric PROXI-WELDY Montageanleitung

Lincoln Electric

Lincoln Electric SQUARE WAVE IM10059 Bedienungsanleitung

Lincoln Electric

Lincoln Electric MIG PULSER IM555 Bedienungsanleitung

Lincoln Electric

Lincoln Electric Flextec 500 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE S350 Bedienungsanleitung

Lincoln Electric

Lincoln Electric 11499 Bedienungsanleitung

Lincoln Electric

Lincoln Electric IDEALARC R3R-300 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC 275S Bedienungsanleitung

Lincoln Electric

Lincoln Electric WELD-PACK 100 PLUS IM546 Bedienungsanleitung

Lincoln Electric

Lincoln Electric WELDLINE WTT2 20W Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V320-T AC/DC Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWERFEED 10S IM850-A Bedienungsanleitung

Lincoln Electric

Lincoln Electric BURNY KALIBURN Spirit II 275 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INNERSHIELD PRO K126-10 Bedienungsanleitung

Lincoln Electric

Lincoln Electric LF-72/74 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER MIG SVM160-B Bedienungsanleitung

Lincoln Electric

Lincoln Electric HOT ROD 500S Bedienungsanleitung

Lincoln Electric

Lincoln Electric STT-10 HEAD & CONTROLS BOOM MOUNT OR BENCH MODELS... Bedienungsanleitung

Lincoln Electric

Lincoln Electric LN-25 IM10092 Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Everlast

Everlast POWER MTS 221STi Bedienungsanleitung

Kipor

Kipor KDE180XW Bedienungsanleitung