Lincoln Electric INVERTEC 400TP Bedienungsanleitung

IM3179

12/2022

REV00

INVERTEC®400TP

OPERATOR’S MANUAL

ENGLISH

Lincoln Electric Bester Sp. z o.o.

ul. Jana III Sobieskiego 19A, 58-260 Bielawa, Poland

www.lincolnelectric.eu

English I English

12/05

THANK YOU! For choosing the QUALITY of the Lincoln Electric products.

Please check packaging and equipment for damage. Claims for material damaged in shipment must be notified

immediately to the dealer.

For ease of use, please enter your product identification data in the table below. Model Name, Code & Serial Number

can be found on the machine rating plate.

Model Name:

………………...…………………………….…………………………………………………………………………………………..

Code & Serial number:

………………….……………………………………………….. …………………………………………………….……………..

Date & Where Purchased:

………………………………………………………………... ……………………….…………………………………………..

ENGLISH INDEX

Technical Specifications...................................................................................................................................................... 1

ECO design information ...................................................................................................................................................... 2

Electromagnetic Compatibility (EMC).................................................................................................................................. 4

Safety.................................................................................................................................................................................. 5

Introduction ......................................................................................................................................................................... 7

Installation and Operator Instructions.................................................................................................................................. 7

WEEE ............................................................................................................................................................................... 13

Spare Parts ....................................................................................................................................................................... 13

REACh .............................................................................................................................................................................. 13

Authorized Service Shops Location .................................................................................................................................. 13

Electrical Schematic.......................................................................................................................................................... 13

Accessories....................................................................................................................................................................... 14

Connection Diagram ......................................................................................................................................................... 15

Dimension Diagram........................................................................................................................................................... 16

English 1 English

Technical Specifications

NAME INDEX

INVERTEC®400TP K14390-1

INPUT

Input Voltage U1EMC Class

INVERTEC®400TP 400V ± 15%, 3-phase A

1effI1max

INVERTEC®400TP 16,9A 24,9A

Input Power at Rated Cycle Input Amperes I1max PF(400V)

INVERTEC®400TP

4,0 kVA @100% (GTAW)12,1A 0,89

11,1 kVA @60% (GTAW) 15,7A 0,91

12,9 KVA @40% (GTAW) 18,6A 0,92

11,9 kVA @100% (SMAW) 16,9A 0,91

15,1 kVA @60% (SMAW) 21,5A 0,92

17,4 kVA @40% (SMAW) 24,9A 0,93

RATED OUTPUT

Process

Duty Cycle 40°C

(based on a 10 min. period) Output Current Output Voltage

INVERTEC®400TP

GTAW

100% 300A 22V

60% 360A 24,4V

40% 400A 26V

SMAW

100% 300A 32V

60% 360A 34,4V

40% 400A 36V

OUTPUT RANGE

GTAW SMAW Peak Open Circuit Voltage U0

INVERTEC®400TP 5 – 400A 5 – 400A 85V

RECOMMENDED INPUT CABLE AND FUSE SIZES

Fuse Type gR or Circuit Breaker Type Z Power Lead

INVERTEC®400TP 25A, 400 Vac 4 Conductors, 4,0mm2

DIMENSION

Weight Height Width Length

INVERTEC®400TP 31,5kg 509 mm 294 mm 624 mm

OTHERS

Protection Rating Maximum Gas Pressure

INVERTEC®400TP IP23 0,5MPa (5 bar)

Operating Temperature Storage Temperature

INVERTEC®400TP from -10°C to +40°C from -25°C to 55°C

English 2 English

ECO design information

The equipment has been designed in order to be compliant with the Directive 2009/125/EC and the Regulation

2019/1784/EU.

Efficiency and idle power consumption:

Index Name Efficiency when max power

consumption / Idle power consumption Equivalent model

K14390-1 INVERTEC®400TP 88% / 22W No equivalent model

Idle state occurs under the condition specified in below table

IDLE STATE

Condition Presence

MIG mode

TIG mode X

STICK mode

After 30 minutes of non-working X

Fan off X

The value of efficiency and consumption in idle state have been measured by method and conditions defined in the product

standard EN 60974-1:20XX.

Manufacturer’s name, product name, code number, product number, serial number and date of production can be read from

rating plate.

XXXXXXXXXX

Code: XXXXX XXXXXX-X

S/N: P1YYMMXXXXX

P1 YY MM XXXXX

5A5A 5B 5D5C

XXXXXXX

Where:

1- Manufacturer name and address

2- Product name

3- Code number

4- Product number

5- Serial number

5A- country of production

5B- year of production

5C- month of production

5D- progressive number different for each machine

English 3 English

Typical gas usage for MIG/MAG equipment:

Material type

Wire

diameter

[mm]

DC electrode positive Wire Feeding

[m/min] Shielding Gas Gas flow

[l/min]

Current

[A]

Voltage

[V]

Carbon, low

alloy steel 0,9 ÷ 1,1 95 ÷ 200 18 ÷ 22 3,5 – 6,5 Ar 75%, CO225% 12

Aluminium 0,8 ÷ 1,6 90 ÷ 240 18 ÷ 26 5,5 – 9,5 Argon 14 ÷ 19

Austenic

stainless steel 0,8 ÷ 1,6 85 ÷ 300 21 ÷ 28 3 - 7 Ar 98%, O22% /

He 90%, Ar 7,5% CO22,5% 14 ÷ 16

Copper alloy 0,9 ÷ 1,6 175 ÷ 385 23 ÷ 26 6 - 11 Argon 12 ÷ 16

Magnesium 1,6 ÷ 2,4 70 ÷ 335 16 ÷ 26 4 - 15 Argon 24 ÷ 28

TIG Process:

In TIG welding process, gas usage depends on cross-sectional area of the nozzle. For commonly used torches:

Helium: 14-24 l/min

Argon: 7-16 l/min

Notice: Excessive flow rates causes turbulence in the gas stream which may aspirate atmospheric contamination into the

welding pool.

Notice: A cross wind or draft moving can disrupt the shielding gas coverage, in the interest of saving of protective gas use

screen to block air flow.

End of life

At end of life of product, it has to be disposal for recycling in accordance with Directive 2012/19/EU (WEEE), information

about the dismantling of product and Critical Raw Material (CRM) present in the product, can be found at

https://www.lincolnelectric.com/en-gb/support/Pages/operator-manuals-eu.aspx

English 4 English

Electromagnetic Compatibility (EMC)

01/11

This machine has been designed in accordance with all relevant directives and standards. However, it may still generate

electromagnetic disturbances that can affect other systems like telecommunications (telephone, radio, and television) or

other safety systems. These disturbances can cause safety problems in the affected systems. Read and understand this

section to eliminate or reduce the amount of electromagnetic disturbance generated by this machine.

This machine has been designed to operate in an industrial area. To operate in a domestic area it is necessary

to observe particular precautions to eliminate possible electromagnetic disturbances. The operator must install

and operate this equipment as described in this manual. If any electromagnetic disturbances are detected the

operator must put in place corrective actions to eliminate these disturbances, if necessary with assistance from

Lincoln Electric.

WARNING

Provided that the public low voltage system impedance at the point of common coupling is lower than:

68 mΩfor the INVERTEC®400TP.

This equipment is compliant with IEC 61000-3-11 and IEC 61000-3-12 and can be connected to public low voltage systems.

It is the responsibility of the installer or user of the equipment to ensure, by consultation with the distribution network

operator if necessary, that the system impedance complies with the impedance restrictions.

Before installing the machine, the operator must check the work area for any devices that may malfunction because of

electromagnetic disturbances. Consider the following.

Input and output cables, control cables, and telephone cables that are in or adjacent to the work area and the machine.

Radio and/or television transmitters and receivers. Computers or computer controlled equipment.

Safety and control equipment for industrial processes. Equipment for calibration and measurement.

Personal medical devices like pacemakers and hearing aids.

Check the electromagnetic immunity for equipment operating in or near the work area. The operator must be sure that

all equipment in the area is compatible. This may require additional protection measures.

The dimensions of the work area to consider will depend on the construction of the area and other activities that are

taking place.

Consider the following guidelines to reduce electromagnetic emissions from the machine.

Connect the machine to the input supply according to this manual. If disturbances occur if may be necessary to take

additional precautions such as filtering the input supply.

The output cables should be as short as possible and positioned together as close as possible to each other. If possible

connect the work piece to ground in order to reduce the electromagnetic emissions. The operator must check that

connecting the work piece to ground does not cause problems or unsafe operating conditions for personnel and

equipment.

Shielding of cables in the work area can reduce electromagnetic emissions. This may be necessary for special

applications.

WARNING

EMC classification of this product is class A in accordance with electromagnetic compatibility standard EN 60974-10 which

means that the product is designed to be used in an industrial environment only.

WARNING

The Class A equipment is not intended for use in residential locations where the electrical power is provided by the public

low-voltage supply system. There may be potential difficulties in ensuring electromagnetic compatibility in those locations,

due to conducted as well as radiated disturbances.

English 5 English

Safety

01/11

WARNING

This equipment have to be used by qualified personnel. Be sure that all installation, operation, maintenance and repair

procedures are performed only by qualified person. Read and understand this manual before operating this equipment.

Failure to follow the instructions in this manual could cause serious personal injury, loss of life, or equipment damage. Read

and understand the following explanations of the warning symbols. Lincoln Electric is not responsible for damages caused

by improper installation, improper care or abnormal operation.

WARNING: This symbol indicates that instructions must be followed to avoid serious personal injury, loss

of life, or equipment damage. Protect yourself and others from possible serious injury or death.

READ AND UNDERSTAND INSTRUCTIONS: Read and understand this manual before operating this

equipment. Arc welding can be hazardous. Failure to follow the instructions in this manual could cause

serious personal injury, loss of life, or equipment damage.

ELECTRIC SHOCK CAN KILL: Welding equipment generates high voltages. Do not touch the electrode,

work clamp, or connected work pieces when this equipment is turned on. Insulate yourself from the

electrode, work clamp, and connected work pieces.

ELECTRICALLY POWERED EQUIPMENT: Turn off the input power using the disconnect switch at the

fuse box before working on this equipment. Ground this equipment in accordance with local electrical

regulations.

ELECTRICALLY POWERED EQUIPMENT: Regularly inspect the input, electrode, and work clamp

cables. If any insulation damage exists replace the cable immediately. Do not place the electrode holder

directly on the welding table or any other surface in contact with the work clamp to avoid the risk of

accidental arc ignition.

ELECTROMAGNETIC FIELD MAY BE DANGEROUS: Electric current flowing through any conductor

creates electromagnetic field (EMF). EMF fields may interfere with some pacemakers, and welders having

a pacemaker shall consult their physician before operating this equipment.

CE COMPLIANCE: This equipment complies with the European Community Directives.

ARTIFICIAL OPTICAL RADIATION: According with the requirements in 2006/25/EC Directive and

EN 12198 Standard, the equipment is a category 2. It makes mandatory the adoption of Personal

Protective Equipment (PPE) having filter with a protection degree up to a maximum of 15, as required by

EN169 Standard.

FUMES AND GASES CAN BE DANGEROUS: Welding may produce fumes and gases hazardous to

health. Avoid breathing these fumes and gases. To avoid these dangers the operator must use enough

ventilation or exhaust to keep fumes and gases away from the breathing zone.

ARC RAYS CAN BURN: Use a shield with the proper filter and cover plates to protect your eyes from

sparks and the rays of the arc when welding or observing. To protect the skin, use suitable clothing made

of durable, fireproof material. Protect other nearby personnel with suitable, non-flammable screening and

warn them not to watch the arc nor expose themselves to the arc.

English 6 English

WELDING SPARKS CAN CAUSE FIRE OR EXPLOSION: Remove fire hazards from the welding area

and have a fire extinguisher easily accessible. Welding sparks and hot materials from the welding process

can easily go through small cracks and openings to adjacent areas. Do not weld on any tanks, drums,

containers, or material until the proper steps have been taken to insure that no flammable or toxic vapors

will be present. Never use this equipment when flammable gases, vapors or flammable liquids are

present.

WELDED MATERIALS CAN BURN: Welding generates a large amount of heat. Hot surfaces and

materials in work area can cause serious burns. Use gloves and pliers when touching or moving

materials in the work area.

CYLINDER MAY EXPLODE IF DAMAGED: Use only certificate, compressed gas cylinders containing

the correct shielding gas for the process used and properly operating regulators designed for the gas and

pressure used. Always keep cylinders in an upright position securely chained to a fixed support. Do not

move or transport gas cylinders with the protection cap removed. Do not allow the electrode, electrode

holder, work clamp or any other electrically live part to touch a gas cylinder. Gas cylinders must be

located away from areas where they may be subjected to physical damage or the welding process

including sparks and heat sources.

MOVING PARTS ARE DANGEROUS: There are moving mechanical parts in this machine, which can

cause serious injury. Keep your hands, body and clothing away from those parts during machine starting,

operating and servicing.

CAUTION: The high frequency used for contact-free ignition with TIG (GTAW) welding, can interfere with

the operation of insufficiently shielded computer equipment, EDP centers and industrial robots, even

causing complete system breakdown. TIG (GTAW) welding may interfere with electronic telephone

networks and with radio and TV reception.

HOT COOLANT CAN BURN SKIN: Always be sure coolant is NOT HOT before servicing the cooler.

SAFETY MARK: This equipment is suitable for supplying power for welding operations carried out in an

environment with increased risk of electric shock.

The manufacturer reserves the right to make changes and/or improvements in design without upgrade at the same time the

operator’s manual.

English 7 English

Introduction

The welding machines INVERTEC®400TP enables

welding:

GTAW (TIG),

SMAW (MMA),

GOUGING (CAG).

The complete package contains:

Work lead – 5m,

Gas hose – 1,5m,

Manual Instruction (USB).

Recommended equipment, which can be bought by user,

was mentioned in the chapter "Accessories".

Installation and Operator Instructions

Read this entire section before installation or operation of

the machine.

Location and Environment

This machine will operate in harsh environments.

However, it is important that simple preventative

measures are followed to assure long life and reliable

operation.

Do not place or operate this machine on a surface with

an incline greater than 15° from horizontal.

Do not use this machine for pipe thawing.

This machine must be located where there is free

circulation of clean air without restrictions for air

movement to and from the air vents. Do not cover the

machine with paper, cloth or rags when switched on.

Dirt and dust that can be drawn into the machine

should be kept to a minimum.

This machine has a protection rating of IP23. Keep it

dry when possible and do not place it on wet ground

or in puddles.

Locate the machine away from radio controlled

machinery. Normal operation may adversely affect the

operation of nearby radio controlled machinery, which

may result in injury or equipment damage. Read the

section on electromagnetic compatibility in this

manual.

Do not operate in areas with an ambient temperature

greater than 40°C.

Duty cycle and Overheating

The duty cycle of a welding machine is the percentage of

time in a 10 minute cycle at which the welder can operate

the machine at rated welding current.

Example: 60% duty cycle

Welding for 6 minutes. Break for 4 minutes.

Excessive extension of the duty cycle will cause the

thermal protection circuit to activate.

Minutes or decrease

Duty Cycle

Input Supply Connection

WARNING

Only a qualified electrician can connect the welding

machine to the supply network. Installation had to be

made in accordance with the appropriate National

Electrical Code and local regulations.

Check the input voltage, phase and frequency supplied to

this machine before turning it on. Verify the connection of

ground wires from the machine to the input source. The

welding machine INVERTEC®400TP must be connected

to a correctly installed plug-in socket with an earth pin.

Input voltage is 400 Vac 50/60Hz. For more information

about input supply refer to the technical specification

section of this manual and to the rating plate of the

machine.

Make sure that the amount of mains power available from

the input supply is adequate for normal operation of the

machine. The necessary delayed fuse or circuit breaker

and cable sizes are indicated in the technical specification

section of this manual.

WARNING

The welding machine can be supplied from a power

generator of output power at least 30% larger than input

power of the welding machine.

WARNING

When powering the machine from a generator be sure to

turn off welder first, before generator is shut down, in

order to prevent damage to welder!

English 8 English

Output Connections

Refer to points [3] and [7] of the Figures below.

Controls and Operational Features

Figure 1

1. Display Cover. Display protection for User Interface.

2. User Interface: See User Interfaces chapter.

3. Positive Output Socket for the Welding Circuit:

Depending on the process to connecting:

Process Symbol Description

GTAW

Work Lead

SMAW

Electrode Holder with lead /

work lead depending on

the require configuration

GAUGE

Gauge Torch / work lead

depending on the require

configuration

4. Remote Control Connector Plug: To install

Remote Control Kit. This connector allows

connection Remote Control. See

"Accessories" chapter.

5. TIG Control Connector: To connect TIG

Torch Trigger or "Up and Down".

6. Gas Connector: Connection TIG torch gas

line.

7. Negative Output Socket for the Welding Circuit:

Depending on the process to connecting:

Process Symbol Description

GTAW

TIG Torch

SMAW

Electrode Holder with lead /

work lead depending on

the require configuration

GAUGE

Gauge Torch / work lead

depending on the require

configuration

Figure 2

8. Power Switch ON/OFF (I/O): Controls the input

power to the machine. Be sure the power source is

connected to the mains supply before turning power

on ("I").

9. Main Intput Cord (5m): Connect the supply plug to

the existing input cable that is rated for the machine

as indicated in this manual, and conforms to all

applicable standards. This connection shall be

performed by a qualified person only.

10. Gas Quick Coupling Socket: For connecting

a gas line.

WARNING

The machine allows the use all suitable shielding gases

with a maximum pressure of 5 bar.

11. Fuse F1: Use the 2A/400V (6,3x32mm) slow-blow

fuse. See "Spare Parts" chapter.

12. Fuse F2: Use the 2A/400V (6,3x32mm) slow-blow

fuse. See "Spare Parts" chapter.

Inhaltsverzeichnis

Andere Lincoln Electric Schweißsystem Handbücher

Lincoln Electric

Lincoln Electric statiflex 200-m Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE POWER WAVE WELDING SYSTEMS Bedienungsanleitung

Lincoln Electric

Lincoln Electric Air Vantage 600 Bedienungsanleitung

Lincoln Electric

Lincoln Electric MIG Wires Guide Bedienungsanleitung

Lincoln Electric

Lincoln Electric RED-D-ARC VIPER Bedienungsanleitung

Lincoln Electric

Lincoln Electric 12719 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER FEED IM915 Bedienungsanleitung

Lincoln Electric

Lincoln Electric Invertec 135S Bedienungsanleitung

Lincoln Electric

Lincoln Electric ASPECT 200 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE S500 Bedienungsanleitung

Lincoln Electric

Lincoln Electric WELDMARK 225 Bedienungsanleitung

Lincoln Electric

Lincoln Electric PYTHON-PLUS K2447-2 Bedienungsanleitung

Lincoln Electric

Lincoln Electric WELD-PAK 100 IMT460-D Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC 165SX Bedienungsanleitung

Lincoln Electric

Lincoln Electric LINC 405-S Bedienungsanleitung

Lincoln Electric

Lincoln Electric CLASSIC III 10033 Bedienungsanleitung

Lincoln Electric

Lincoln Electric RED-D-ARC GX 300 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE 405 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER-ARC 4000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric Flextec 500X Bedienungsanleitung

Lincoln Electric

Lincoln Electric DC-650 PRO IM463-A Bedienungsanleitung

Lincoln Electric

Lincoln Electric AIR VANTAGE 500 Bedienungsanleitung

Lincoln Electric

Lincoln Electric LINC FEED 37 Bedienungsanleitung

Lincoln Electric

Lincoln Electric OUTBACK SVM204-A Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Everlast

Everlast POWER MTS 221STi Bedienungsanleitung

Kipor

Kipor KDE180XW Bedienungsanleitung