Lincoln Electric POWERTEC i320C STANDARD Bedienungsanleitung

English English

IM3070

09/2018

REV04

POWERTEC i250C STANDARD

POWERTEC i250C ADVANCED

POWERTEC i320C STANDARD

POWERTEC i320C ADVANCED

OPERATOR’S MANUAL

ENGLISH

Lincoln Electric Bester Sp. z o.o.

ul. Jana III Sobieskiego 19A, 58-263 Bielawa, Poland

www.lincolnelectric.eu

English English

12/05

THANKS! For having choosen the QUALITY of the Lincoln Electric products.

Please Examine Package and Equipment for Damage. Claims for material damaged in shipment must be notified

immediately to the dealer.

For future reference record in the table below your equipment identification information. Model Name, Code &

Serial Number can be found on the machine rating plate.

Model Name:

………………...…………………………….…………………………………………………………………………………………..

Code & Serial number:

………………….……………………………………………….. …………………………………………………….……………..

Date & Where Purchased:

…………………………………………………………………... ……………………….…………………………………………..

ENGLISH INDEX

Technical Specifications .................................................................................................................................................. 1

Electromagnetic Compatibility (EMC) .............................................................................................................................. 2

Safety .............................................................................................................................................................................. 3

Introduction...................................................................................................................................................................... 4

Installation and Operator Instructions .............................................................................................................................. 4

WEEE............................................................................................................................................................................ 31

Spare Parts.................................................................................................................................................................... 31

Authorized Service Shops Location............................................................................................................................... 31

Electrical Schematic ...................................................................................................................................................... 31

Accessories ................................................................................................................................................................... 32

English 1 English

Technical Specifications

NAME INDEX

POWERTEC i250C STANDARD K14157-1

POWERTEC i250C ADVANCED K14157-2

POWERTEC i320C STANDARD K14158-1

POWERTEC i320C ADVANCED K14158-2

INPUT

Input Voltage U1EMC Class Frequency

PTi250C STANDARD

PTi250C ADVANCED

PTi320C STANDARD

PTi320C ADVANCED

400V ± 10%

3-phase A 50/60Hz

Input Power at Rated Cycle Input Amperes I1max PF

PTi250C STANDARD

PTi250C ADVANCED

10,3 kVA @ 60% Duty Cycle

(40°C) 14,7A 0,85

PTi320C STANDARD

PTi320C ADVANCED

13,6 kVA @ 40% Duty Cycle

(40°C) 19,6A 0,90

RATED OUTPUT

Open Circuit

Voltage

Duty Cycle 40°C

(based on a 10 min. Output Current Output Voltage

PTi250C STANDARD

PTi250C ADVANCED

GMAW 49Vdc 60% 250A 26,5Vdc

100% 195A 23,8Vdc

FCAW 49Vdc 60% 250A 26,5Vdc

100% 195A 23,8Vdc

SMAW 49Vdc 60% 250A 30Vdc

100% 195A 27,8Vdc

PTi320C STANDARD

PTi320C ADVANCED

GMAW 49Vdc 40% 320A 30Vdc

100% 195A 23,8Vdc

FCAW 49Vdc 40% 320A 30Vdc

100% 195A 23,8Vdc

SMAW 49Vdc 40% 320A 32,8Vdc

100% 195A 27,8Vdc

WELDING CURRENT RANGE

GMAW FCAW SMAW

PTi250C STANDARD

PTi250C ADVANCED 10A÷250A 10A÷250A 20A÷250A

PTi320C STANDARD

PTi320C ADVANCED 10A÷320A 10A÷320A 20A÷320A

RECOMMENDED INPUT CABLE AND FUSE SIZES

Fuse Type gR or Circuit Breaker Type Z Power Lead

PTi250C STANDARD

PTi250C ADVANCED 16A, 400V AC 4 Conductor, 2,5mm2

PTi320C STANDARD

PTi320C ADVANCED 20A, 400V AC 4 Conductor, 2,5mm2

DIMENSION

Weight Height Width Length

66 kg 535 mm 300 mm 635 mm

Protection Rating Operating Humidity

(

t=20°C

)

Operating

Temperature

Storage

Temperature

IP23 ≤90 % from -10 ºC

to +40 ºC

from -25 ºC

to +55 ºC

English 2 English

Electromagnetic Compatibility (EMC)

11/04

This machine has been designed in accordance with all relevant directives and standards. However, it may still generate

electromagnetic disturbances that can affect other systems like telecommunications (telephone, radio, and television) or

other safety systems. These disturbances can cause safety problems in the affected systems. Read and understand this

section to eliminate or reduce the amount of electromagnetic disturbance generated by this machine.

WARNING

Provided that the public low voltage system impedance at the point of common coupling is

lower than:

56,4 mΩfor the Powertec i250/320.

This equipment is compliant with IEC 61000-3-11 and IEC-3-12 and can be connected to public lowvoltage systems. It is

the responsibility of the installer or user of the equipment to ensure, by consultation with the distribution network operator

if necessary, that the system impedance complies with the impedance restrictions.



Consider the following guidelines to reduce electromagnetic emissions from the machine.

Connect the machine to the input supply according to this manual. If disturbances occur if may be necessary to take

additional precautions such as filtering the input supply.

The output cables should be kept as short as possible and should be positioned together. If possible connect the

work piece to ground in order to reduce the electromagnetic emissions. The operator must check that connecting the

work piece to ground does not cause problems or unsafe operating conditions for personnel and equipment.

Shielding of cables in the work area can reduce electromagnetic emissions. This may be necessary for special

applications.

WARNING

The Class A equipment is not intended for use in residential locations where the electrical power is provided by the public

low-voltage supply system. There may be potential difficulties in ensuring electromagnetic compatibility in those

locations, due to conducted as well as radiated disturbances.

WARNING

While a high electromagnetic field occurs, a welding current can fluctuate.

English 3 English

Safety

01/11

WARNING

This equipment must be used by qualified personnel. Be sure that all installation, operation, maintenance and repair

procedures are performed only by qualified person. Read and understand this manual before operating this equipment.

Failure to follow the instructions in this manual could cause serious personal injury, loss of life, or damage to this

equipment. Read and understand the following explanations of the warning symbols. Lincoln Electric is not responsible

for damages caused by improper installation, improper care or abnormal operation.

WARNING: This symbol indicates that instructions must be followed to avoid serious personal injury,

loss of life, or damage to this equipment. Protect yourself and others from possible serious injury or

death.

READ AND UNDERSTAND INSTRUCTIONS: Read and understand this manual before operating

this equipment. Arc welding can be hazardous. Failure to follow the instructions in this manual could

cause serious personal injury, loss of life, or damage to this equipment.

ELECTRIC SHOCK CAN KILL: Welding equipment generates high voltages. Do not touch the

electrode, work clamp, or connected work pieces when this equipment is on. Insulate yourself from

the electrode, work clamp, and connected work pieces.

ELECTRICALLY POWERED EQUIPMENT: Turn off input power using the disconnect switch at the

fuse box before working on this equipment. Ground this equipment in accordance with local electrical

regulations.

ELECTRICALLY POWERED EQUIPMENT: Regularly inspect the input, electrode, and work clamp

cables. If any insulation damage exists replace the cable immediately. Do not place the electrode

holder directly on the welding table or any other surface in contact with the work clamp to avoid the

risk of accidental arc ignition.

ELECTRIC AND MAGNETIC FIELDS MAY BE DANGEROUS: Electric current flowing through any

conductor creates electric and magnetic fields (EMF). EMF fields may interfere with some

pacemakers, and welders having a pacemaker shall consult their physician before operating this

equipment.

CE COMPLIANCE: This equipment complies with the European Community Directives.

ARTIFICIAL OPTICAL RADIATION: According with the requirements in 2006/25/EC Directive and

EN 12198 Standard, the equipment is a category 2. It makes mandatory the adoption of Personal

Protective Equipments (PPE) having filter with a protection degree up to a maximum of 15, as

required by EN169 Standard.

FUMES AND GASES CAN BE DANGEROUS: Welding may produce fumes and gases hazardous to

health. Avoid breathing these fumes and gases. To avoid these dangers the operator must use

enough ventilation or exhaust to keep fumes and gases away from the breathing zone.

ARC RAYS CAN BURN: Use a shield with the proper filter and cover plates to protect your eyes from

sparks and the rays of the arc when welding or observing. Use suitable clothing made from durable

flame-resistant material to protect you skin and that of your helpers. Protect other nearby personnel

with suitable, non-flammable screening and warn them not to watch the arc nor expose themselves to

the arc.

WELDING SPARKS CAN CAUSE FIRE OR EXPLOSION: Remove fire hazards from the welding

area and have a fire extinguisher readily available. Welding sparks and hot materials from the welding

process can easily go through small cracks and openings to adjacent areas. Do not weld on any

tanks, drums, containers, or material until the proper steps have been taken to insure that no

flammable or toxic vapors will be present. Never operate this equipment when flammable gases,

vapors or liquid combustibles are present.

WELDED MATERIALS CAN BURN: Welding generates a large amount of heat. Hot surfaces and

materials in work area can cause serious burns. Use gloves and pliers when touching or moving

materials in the work area.

English 4 English

SAFETY MARK: This equipment is suitable for supplying power for welding operations carried out in

an environment with increased hazard of electric shock.

CYLINDER MAY EXPLODE IF DAMAGED: Use only compressed gas cylinders containing the

correct shielding gas for the process used and properly operating regulators designed for the gas and

pressure used. Always keep cylinders in an upRight position securely chained to a fixed support. Do

not move or transport gas cylinders with the protection cap removed. Do not allow the electrode,

electrode holder, work clamp or any other electrically live part to touch a gas cylinder. Gas cylinders

must be located away from areas where they may be subjected to physical damage or the welding

process including sparks and heat sources.

The manufacturer reserves the Right to make changes and/or improvements in design without upgrade at the same time

the operator’s manual.

Introduction

General Description

The welding machines

POWERTEC i250C STANDARD

POWERTEC i250C ADVANCED

POWERTEC i320C STANDARD

POWERTEC i320C ADVANCED

enables welding:

GMAW (MIG/MAG),

FCAW (Flux-Cored),

SMAW (MMA),

The following equipment has been added to

POWERTEC i250C STANDARD

POWERTEC i250C ADVANCED

POWERTEC i320C STANDARD

POWERTEC i320C ADVANCED

Work lead – 3m,

Gas hose – 2m,

Driving roll V1.0/V1.2 for solid wire (mounted in the

wire feeder).

Recommended equipment, which can be bought by

user, was mentioned in the chapter "Accessories".

Installation and Operator Instructions

Read this entire section before installation or operation of

the machine.

Location and Environment

This machine will operate in harsh environments.

However, it is important that simple preventative

measures are followed to assure long life and reliable

operation.

Do not place or operate this machine on a surface

with an incline greater than 15° from horizontal.

Do not use this machine for pipe thawing.

This machine must be located where there is free

circulation of clean air without restrictions for air

movement to and from the air vents. Do not cover

the machine with paper, cloth or rags when switched

on.

Dirt and dust that can be drawn into the machine

should be kept to a minimum.

This machine has a protection rating of IP23. Keep it

dry when possible and do not place it on wet ground

or in puddles.

Locate the machine away from radio controlled

machinery. Normal operation may adversely affect

the operation of nearby radio controlled machinery,

which may result in injury or equipment damage.

Read the section on electromagnetic compatibility in

this manual.

Do not operate in areas with an ambient temperature

greater than 40°C.

Duty cycle and Overheating

The duty cycle of a welding machine is the percentage of

time in a 10 minute cycle at which the welder can operate

the machine at rated welding current.

Example: 60% duty cycle

Welding for 6 minutes. Break for 4 minutes.

Excessive extension of the duty cycle will cause the

thermal protection circuit to activate.

Minutes or decrease

Duty Cycle

English 5 English

Input Supply Connection

WARNING

Only a qualified electrician can connect the welding

machine to the supply network. Installation had to be

made in accordance with the appropriate National

Electrical Code and local regulations.

Check the input voltage, phase and frequency supplied to

this machine before turning it on. Verify the connection of

ground wires from the machine to the input source. The

welding machine POWERTEC i250C STANDARD/

ADVANCED, POWERTEC i320C STANDARD/

ADVANCED must be connected to a correctly installed

plug-in socket with an earth pin.

Input voltage is 400 Vac 50/60Hz. For more information

about input supply refer to the technical specification

section of this manual and to the rating plate of the

machine.

Make sure that the amount of mains power available from

the input supply is adequate for normal operation of the

machine. The necessary delayed fuse or circuit breaker

and cable sizes are indicated in the technical

specification section of this manual.

WARNING

The welding machine can be supplied from a power

generator of output power at least 30% larger than input

power of the welding machine.

WARNING

When powering the machine from a generator be sure to

turn off welder first, before generator is shut down, in

order to prevent damage to welder!

Output Connections

Refer to points [3], [4] and [5] of the Figures below.

Controls and Operational Features

Front Panel

Standard Version

Figure 1.

1. U0 User Interface: See “User Interfaces” Chapter.

2. Power Switch ON/OFF (I/O): Controls the input power

to the machine. Be sure the power source is

connected to the mains supply before turning power

on ("I"). After input power is connected and the power

switch is turned on, the indicator will light up to

indicate the machine is ready to weld.

3. Negative Output Socket for the Welding

Circuit: For connecting an electrode holder

with lead / work lead.

4. Positive Output Socket for the Welding

Circuit: For connecting an electrode holder

with lead / work lead.

5. EURO Socket: For connecting a welding gun (for

GMAW / FCAW process).

Front Panel

Advanced Version

Figure 2.

6. U7 User Interface: See User Interfaces chapter.

7. Remote Control Connector Plug: To install Remote

Control Kit. This connector allows connection Remote

Control. See "Accessories" chapter.

English 6 English

Rear panel

Figure 3.

8. Wire Liner Entry: Enables installing liner for welding

wire delivered in drum package.

9. Chain: To protect gas bottle.

10. Power Lead (5m): Connect the supply plug to the

existing input cable that is rated for the machine as

indicated in this manual, and conforms to all

applicable standards. This connection shall be

performed by a qualified person only.

11. Supply Plug: For CO2 gas heater kit (see

“Accessories” chapter).

12. Gas Connector: Connection for gas line.

13. Gas Flow Regulator Plug: Gas flow regulator can be

purchased separately (see “Accessories” chapter).

14. Gas hose

15. Work Lead

Internal Controls

Figure 4.

16. Spooled Wire (for GMAW / FCAW): The machine

does not include a spooled wire.

17. Wire Spool Support: Maximum 16kg spools. Accepts

plastic, steel and fiber spools onto 51 mm spindle.

Note: Plastic Brake Nut has a Left-hand thread.

18. Cold Inch/ Gas Purge Switch: This switch enables

wire feeding or gas flow without turning on output

voltage.

19. Wire drive feeding system: 4-Roll wire drive

mechanisms with quick-change feed rolls.

20. Terminal Block of Changing Polarity Plug (for GMAW /

FCAW-SS process): This terminal block enables to

set the welding polarity (+ ; -), which will be given at

the welding gun (see “Accessories” chapter).

21a. USB Receptacle Type A (Advanced only):

For USB memory stick connection. For machine

software update and service purpose.

21b. Fuse F1:

Use the 1A/400V (6,3x32mm) low blow fuse.

Stnadard User Interface (U0)

Figure 5.

22. Display:

Left display: Shows wire feed speed or welding

current. During welding shows the actual

welding current value.

Right display: Shows the welding voltage in

volts units. During welding shows the actual

welding voltage value.

23. Right Control: Adjusts values on the Right display.

24. Left Control: Adjusts values on the Left display.

25. Right Button: Enables scrolling, changing and setting

welding parameters.

26. Left Button: Enables changing the welding process.

English 7 English

27. Thermal Overload Indicator: It indicates that the

machine is overloaded or that the cooling is not

sufficient.

28. Status LED: A two color light that indicates system

errors. Normal operation is steady green light. Error

conditions are indicated, per Table 1.

WARNING

The status light will flash green, and sometimes red and

green, for up to one minute when the machine is first

turned on. When the power source is powered it can take

as long as 60 seconds for the machine to be ready to

weld. This is a normal situation as the machine goes

through initialization.

Table 1.

LED Light

Condition

Meaning

Only machines which using ArcLink®

protocol for communication

Steady Green System OK. Power source is

operational, and is communicating

normally with all healthy peripheral

equipment.

Blinking Green Occurs during power up or a system

reset, and indicates the power source

is mapping (identifying)

each component in the system.

Normal for first 1-10 seconds after

power is turned on, or if the system

configuration is changed during

operation.

Alternating Green

and Red

If the status lights are flashing any

combination of red and green, errors

are present in the power source.

Individual code digits are flashed in

red with a long pause between digits.

If more than one code is present, the

codes will be separated by green

light. Read the error code before the

machine is turned off.

If occurs, to clear the error try to turn

Off the machine, wait for a few

seconds, then turn ON again. If the

error remains, a maintenance is

required. Please contact the nearest

authorized technical service center or

Lincoln Electric and report the error

code read.

Steady Red Indicate no communication between

the power source and device which

has been connected to this power

source.

29. LED Indicator: Informs that the wire feed speed is on

the Left display.

30. LED Indicator: Informs that the value on the Left

display is in ampere units.

31. LED Indicator: Informs that the value on the Right

display is in volts unit.

32. Welding Programs Indicators: lamps indicate the

active weld mode. Descriptions of parameters are in

Table 2.

33. Welding parameters Indicators: lamps indicate the

active weld parameters. Descriptions of parameters

are in Table 3.

Welding Process Change

It is possible to quick recall of one of the six manual

welding programs - Table 2.

Table 2. Manual Weld Modes:

Symbol LED Process

GMAW

GMAW MIX

GMAW CO2

GMAW AR

FCAW

FCAW MIX

FCAW CO2

SMAW

To set the welding process:

Press the Left Button [26] to select an adequate

welding process- the weld program indicator [32]

the first weld program indicator [32] lights on.

Again, press the Left Button [26] the weld

program indicator will jump to the next mode.

WARNING

During switching the displays show a “creeping line” on

the screen.

English 8 English

Quick Access and Configuration Menu for

U0 User Interface

Users have access to the two menu levels:

Quick Access – basic menu which is connected with

setting the Welding Parameters.

Configuration Menu – advanced menu, configures

the device setting.

WARNING

The Menu cannot be accessed if the system is

welding, or if there is a fault (status LED is not solid

green).

The availability parameters in the Quick Access and

Configuration Menu depend on the selected welding

program / welding process.

After the device has been restarted the user settings are

restored.

Parameter Selection Mode – the Parameter Name on the

Left Display blinking.

Parameter Change Value Mode – the parameter value on

the Right Display blinking.

Quick Access

To set the parameter of Quick Access (Table 3):

Press the Right Button [25] to select mode.

Turn the Right Knob [24] to set the value of

parameter.

Press the Left Button [26] to retutn to main menu.

WARNING

If user do not press Left button, system return

automatically to the main menu after few seconds.

Table 3. The default settings of Quick Access

Paramete

Definition

Inductance – controls the arc characteristics when

short-arc welding. increasing Inductance greater than

0.0 results in a crisper arc (more spatter) while

decreasing the Inductance to less than 0.0 provides a

softer arc (less spatter).

Adjust range: from -10 to +10.

Factory default, Pinch is OFF.

The 2-Step - 4-Step changes the function of the

gun’s trigger.

2 Step trigger operation turns welding on and off

in direct response to the trigger. Welding process

is performed when the gun’s trigger is pulled.

4-Step mode allows to continue welding, when the

gun’s trigger is released. To stop welding, the

gun’s trigger is pulled again. 4-step mode

facilitates to making long welds.

Note: 4-Step does not work during Spot Welding.

Run-in WFS – sets the wire feed speed from the time

the trigger is pulled until an arc is established.

Factory default, Run-in is turned off.

Adjust range: from minimum to 3,81 m/min (150

in/min ).

Burnback Time – is the amount of time that the weld

output continues after the wire stops feeding. It

prevents the wire from sticking in the puddle and

prepares the end of the wire for the next arc start.

Factory default, Burnback Time is set at AUTO.

Adjust range: from 0 (OFF) to 0,25 seconds.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lincoln Electric Schweißsystem Handbücher

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung

Lincoln Electric

Lincoln Electric Power MIG 215 Bedienungsanleitung

Lincoln Electric

Lincoln Electric CWT WOC-2 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER FEED IM892-C Bedienungsanleitung

Lincoln Electric

Lincoln Electric SAE-400 SEVERE DUTY IM727 Bedienungsanleitung

Lincoln Electric

Lincoln Electric EuropurePLUS 5500 LS Wartungshandbuch

Lincoln Electric

Lincoln Electric LN-742 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER-ARC 4000 SVM103-A Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE C300 CE Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC SVM199-A Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC POWER WAVE 450 SVM112-B Bedienungsanleitung

Lincoln Electric

Lincoln Electric Vantage 322 Bedienungsanleitung

Lincoln Electric

Lincoln Electric AIR VANTAGE IM10066 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWERTEC 305C PRO Bedienungsanleitung

Lincoln Electric

Lincoln Electric Idealarc R3R-400 Bedienungsanleitung

Lincoln Electric

Lincoln Electric OUTBACK 145 Bedienungsanleitung

Lincoln Electric

Lincoln Electric MULTI-SOURCE IM692 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC 160 TPX Bedienungsanleitung

Lincoln Electric

Lincoln Electric RED-D-ARC FX450 Bedienungsanleitung

Lincoln Electric

Lincoln Electric WELDING POWER SOURCES AC-225-S Bedienungsanleitung

Lincoln Electric

Lincoln Electric Cobramatic K2259-1 Bedienungsanleitung

Lincoln Electric

Lincoln Electric power wave ac/dc 1000 sd Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE S500CE IM10123 Bedienungsanleitung

Lincoln Electric

Lincoln Electric RANGER IM836-B Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Everlast

Everlast POWER MTS 221STi Bedienungsanleitung

Kipor

Kipor KDE180XW Bedienungsanleitung

OrienTek

OrienTek T40 Bedienungsanleitung