Lincoln Electric SAE-300 HE Bedienungsanleitung

Operator’s Manual

SAE-300 ®HE

www.lincolnelectric.com/register

Authorized Servi e and Distributor Lo ator:

www.lincolnelectric.com/locator

IM10154-A | Issue D ate Jan- 14

For use with machines having Code Numbers:

11906, 12162

Need Help? Call 1.888.935.3877

to talk to a Service Representative

Hours of Operation:

8:00 AM to 6:00 PM (E ) Mon. thru Fri.

After hours?

Use “Ask the Experts” at lincolnelectric.com

A Lincoln Service Representative will contact you

no later than the following business day.

For Servi e outside the USA:

Email: [email protected]

Save for future referen e

Date Purchased

Code: (ex: 10859)

Serial: (ex: U1060512345)

THANK YOU FOR SELECTING

A QUALITY PRODUCT BY

LINCOLN ELEC TRIC.

!

"

When this equipment is shipped, title passes to the purchaser upon

receipt by the carrier. Consequently, Claims for material damaged in

shipment must be made by the purchaser against the transportation

company at the time the shipment is received.

""

incoln arc welding and cutting equipment is designed and built with

safety in mind. However, your overall safety can be increased by

proper installation ... and thoughtful operation on your part.

DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT

WITHOUT READING THIS MANUAL AND THE SAFETY PRECAUTIONS

CONTAINED THROUGHOUT. And, most importantly, think before you

act and be careful.

This statement appears where the information must be followed

exactly to avoid serious personal injury or loss of life.

This statement appears where the information must be followed to

avoid minor personal injury or damage to this equipment.

"

DON’T get too close to the arc. Use

corrective lenses if necessary to

stay a reasonable distance away

from the arc.

READ and obey the Material Safety

Data Sheet (MSDS) and the warning

label that appears on all containers

of welding materials.

USE ENOUGH VENTILATION or

exhaust at the arc, or both, to keep

the fumes and gases from your breathing zone and the general area.

IN A LARGE ROOM OR OUTDOORS, natural ventilation may be

adequate if you keep your head out of the fumes (See below).

USE NATURAL DRAFTS or fans to keep the fumes away from your

face.

If you de velop unusual symptoms, see your supervisor. Perhaps the

welding atmosphere and ventilation system should be checked.

""

PROTECT your eyes and face with welding helmet

properly fitted and with proper grade of filter plate

(See ANSI Z49.1).

PROTECT your body from welding spatter and arc

flash with protective clothing including woolen

clothing, flame-proof apron and gloves, leather

leggings, and high boots.

PROTECT others from splatter, flash, and glare with

protective screens or barriers.

IN SOME AREAS, protection from noise may be

appropriate.

BE SURE protective equipment is in good condition.

Also, wear safety glasses in work area AT A

TIMES.

SPECIA SITUATIONS

DO NOT WELD OR CUT containers or materials which previously had

been in contact with hazardous substances unless they are properly

cleaned. This is extremely dangerous.

DO NOT WELD OR CUT painted or plated parts unless special

precautions with ventilation have been taken. They can release highly

toxic fumes or gases.

Additional precautionary measures

PROTECT compressed gas cylinders from excessive heat, mechanical

shocks, and arcs; fasten cylinders so they cannot fall.

BE SURE cylinders are never grounded or part of an electrical circuit.

REMOVE all potential fire hazards from welding area.

ALWAYS HAVE FIRE FIGHTING EQUIPMENT READY FOR

IMMEDIATE USE AND KNOW HOW TO USE IT.

-($$

+*%$

SECTION A:

WARNINGS

"%($&(%&%)*%$-($$)

Diesel Engines

Diesel engine exhaust and some of its constituents are known

to the State of California to cause cancer, birth defects, and other

reproductive harm.

Gasoline Engines

The engine exhaust from this product contains chemicals known

to the State of California to cause cancer, birth defects, or other

reproductive harm.

 #

"

" "

  



Read and understand the following safety highlights. For additional

safety information, it is strongly recommended that you purchase a

copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the

American Welding Society, P.O. Box 351040, Miami, Florida 33135 or

CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety”

booklet E205 is available from the incoln Electric Company, 22801

St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION,

MAINTENANCE AND REPAIR PROCEDURES ARE

PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

FOR ENGINE POWERED

EQUIPMENT.

1.a. Turn the engine off before troubleshooting

and maintenance work unless the

maintenance work requires it to be running.

1.b. Operate engines in open, well-ventilated

areas or vent the engine exhaust fumes outdoors.

1.c. Do not add the fuel near an open flame

welding arc or when the engine is running.

Stop the engine and allow it to cool before

refueling to prevent spilled fuel from

vaporizing on contact with hot engine parts

and igniting. Do not spill fuel when filling

tank. If fuel is spilled, wipe it up and do not start engine until

fumes have been eliminated.

1.d. Keep all equipment safety guards, covers and

devices in position and in good repair.Keep

hands, hair, clothing and tools away from

V-belts, gears, fans and all other moving parts

when starting, operating or repairing

equipment.

1.e. In some cases it may be necessary to remove safety guards to

perform required maintenance. Remove guards only when

necessary and replace them when the maintenance requiring

their removal is complete. Always use the greatest care when

working near moving parts.

1.f. Do not put your hands near the engine fan. Do not attempt to

override the governor or idler by pushing on the throttle control

rods while the engine is running.

1.g. To prevent accidentally starting gasoline engines while turning

the engine or welding generator during maintenance work,

disconnect the spark plug wires, distributor cap or magneto wire

as appropriate.

1.h. To avoid scalding, do not remove the radiator

pressure cap when the engine is hot.

ELECTRIC AND

MAGNETIC FIELDS MAY

BE DANGEROUS

2.a. Electric current flowing through any conductor

causes localized Electric and Magnetic Fields (EMF). Welding

current creates EMF fields around welding cables and welding

machines

2.b. EMF fields may interfere with some pacemakers, and welders

having a pacemaker should consult their physician before

welding.

2.c. Exposure to EMF fields in welding may have other health effects

which are now not known.

2.d. All welders should use the following procedures in order to

minimize exposure to EMF fields from the welding circuit:

2.d.1. Route the electrode and work cables together - Secure

them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and work

cables. If the electrode cable is on your right side, the

work cable should also be on your right side.

2.d.4. Connect the work cable to the workpiece as close as pos-

sible to the area being welded.

2.d.5. Do not work next to welding power source.

SAFETY

ELECTRIC SHOCK

CAN KILL.

3.a. The electrode and work (or ground) circuits are

electrically “hot” when the welder is on. Do

not touch these “hot” parts with your bare skin

or wet clothing. Wear dry, hole-free gloves to insulate hands.

3.b. Insulate yourself from work and ground using dry insulation.

Make certain the insulation is large enough to cover your full area

of physical contact with work and ground.

0$'',6,10616+(014/$.5$)(6;24(&$76,105,)

9(.',0*/756%(2(4)14/('70'(4(.(&64,&$..;

+$<$4'175&10',6,105,0'$/2.1&$6,105149+,.(

9($4,0*9(6&.16+,0*10/(6$.5647&674(557&+$5

).1145*4$6,0*5145&$))1.'59+(0,0&4$/2('

215,6,10557&+$55,66,0*-0((.,0*14.;,0*,)6+(4(

,5$+,*+4,5-1)70$81,'$%.(14$&&,'(06$.&106$&6

9,6+6+(914-2,(&(14*4170'75(6+()1..19,0*

(37,2/(06

• Semiautomatic DC Constant Voltage (Wire) Welder.

• DC Manual (Stick) Welder.

• AC Welder with Reduced Voltage Control.

3.c. In semiautomatic or automatic wire welding, the electrode,

electrode reel, welding head, nozzle or semiautomatic welding

gun are also electrically “hot”.

3.d. Always be sure the work cable makes a good electrical

connection with the metal being welded. The connection should

be as close as possible to the area being welded.

3.e. Ground the work or metal to be welded to a good electrical (earth)

ground.

3.f. Maintain the electrode holder, work clamp, welding cable and

welding machine in good, safe operating condition. Replace

damaged insulation.

3.g. Never dip the electrode in water for cooling.

3.h. Never simultaneously touch electrically “hot” parts of electrode

holders connected to two welders because voltage

between the

two can be the total of the open circuit voltage of both

welders.

3.i. When working above floor level, use a safety belt to protect

yourself from a fall should you get a shock.

3.j. Also see It ems 6.c. and 8.

ARC RAYS CAN BURN.

4.a. Use a shield with the proper filter and cover plates to protect your

eyes from sparks and the rays of the arc when welding or

observing open arc welding. Headshield and filter lens should

conform to ANSI Z87. I standards.

4.b. Use suitable clothing made from durable flame-resistant material

to protect your skin and that of your helpers from the arc rays.

4.c. Protect other nearby personnel with suitable, non-flammable

screening and/or warn them not to watch the arc nor expose

themselves to the arc rays or to hot spatter or metal.

FUMES AND GASES

CAN BE DANGEROUS.

5.a. Welding may produce fumes and gases

hazardous to health. Avoid breathing these

fumes and gases. When welding, keep your head out of the fume.

Use enough ventilation and/or exhaust at the arc to keep fumes

and gases away from the breathing zone. +(09(.',0*

9,6+(.(&641'(59+,&+4(37,4(52(&,$.8(06,.$6,10

57&+$556$,0.(5514+$4')$&,0*5((,05647&6,105

10&106$,0(4141410.($'14&$'/,7/

2.$6('56((.$0'16+(4/(6$.514&1$6,0*59+,&+

241'7&(+,*+.;61:,&)7/(5-((2(:21574($5.19

$52155,%.($0'9,6+,0$22.,&$%.($0'

.,/,6575,0*.1&$.(:+$75614

/(&+$0,&$.8(06,.$6,100&10),0('52$&(514,0

51/(&,4&7/56$0&(5176'1145$4(52,4$614/$;

%(4(37,4(''',6,10$.24(&$76,105$4($.51

4(37,4('9+(09(.',0*10*$.8$0,<('56((.

5. b. The operation of welding fume control equipment is affected by

various factors including proper use and positioning of the

equipment, maintenance of the equipment and the specific

welding procedure and application involved. Worker exposure

level should be checked upon installation and periodically

thereafter to be certain it is within applicable OSHA PE and

ACGIH T V limits.

5.c. Do not weld in locations near chlorinated hydrocarbon vapors

coming from degreasing, cleaning or spraying operations. The

heat and rays of the arc can react with solvent vapors to form

phosgene, a highly toxic gas, and other irritating products.

5.d. Shielding gases used for arc welding can displace air and

cause

injury or death. Always use enough ventilation, especially in

confined areas, to insure breathing air is safe.

5.e. Read and understand the manufacturer’s instructions for this

equipment and the consumables to be used, including the

material safety data sheet (MSDS) and follow your employer’s

safety practices. MSDS forms are available from your welding

distributor or from the manufacturer.

5.f. Also see item 1.b.

SAFETY

WELDING AND CUTTING

SPARKS CAN CAUSE

FIRE OR EXPLOSION.

6.a. Remove fire hazards from the welding area. If

this is not possible, cover them to prevent the

welding sparks from starting a fire. Remember that welding

sparks and hot materials from welding can easily go through

small cracks and openings to adjacent areas. Avoid welding near

hydraulic lines. Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site, special

precautions should be used to prevent hazardous situations.

Refer to “Safety in Welding and Cutting” (ANSI Standard Z49.1)

and the operating information for the equipment being used.

6.c. When not welding, make certain no part of the electrode circuit is

touching the work or ground. Accidental contact can cause

overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the

proper steps have been taken to insure that such procedures will

not cause flammable or toxic vapors from substances inside.

They can cause an explosion even though they have been

“cleaned”. For information, purchase “Recommended Safe

Practices for the Preparation for Welding and Cutting of

Containers and Piping That Have Held Hazardous Substances”,

AWS F4.1 from the American Welding Society (see address

above).

6.e. Vent hollow castings or containers before heating, cutting or

welding. They may explode.

6.f. Sparks and spatter are thrown from the welding arc. Wear oil free

protective garments such as leather gloves, heavy shirt, cuffless

trousers, high shoes and a cap over your hair. Wear ear plugs

when welding out of position or in confined places. Always wear

safety glasses with side shields when in a welding area.

6.g. Connect the work cable to the work as close to the welding area

as practical. Work cables connected to the building framework or

other locations away from the welding area increase the

possibility of the welding current passing through lifting chains,

crane cables or other alternate circuits. This can create fire

hazards or overheat lifting chains or cables until they fail.

6.h. Also see item 1.c.

6.I. Read and follow NFPA 51B “ Standard for Fire Prevention During

Welding, Cutting and Other Hot Work”, available from NFPA, 1

Batterymarch Park, PO box 9101, Quincy, Ma 022690-9101.

6.j. Do not use a welding power source for pipe thawing.

CYLINDER MAY EXPLODE IF

DAMAGED.

7.a. Use only compressed gas cylinders containing

the correct shielding gas for the process used

and properly operating regulators designed for

the gas and pressure used. All hoses, fittings,

etc. should be suitable for the application and

maintained in good condition.

7.b. Always keep cylinders in an upright position securely chained to

an undercarriage or fixed support.

7.c. Cylinders should be located:

• Away from areas where they may be struck or subjected

to physical damage.

• A safe distance from arc welding or cutting operations

and any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any other

electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet

when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand tight

except when the cylinder is in use or connected for use.

7.g. Read and follow the instructions on compressed gas cylinders,

associated equipment, and CGA publication P-l, “Precautions for

Safe Handling of Compressed Gases in

Cylinders,” available

from the Compressed Gas Association 1235 Jefferson Davis

Highway, Arlington, VA 22202.

FOR ELECTRICALLY

POWERED EQUIPMENT.

8.a. Turn off input power using the disconnect

switch at the fuse box before working on the

equipment.

8.b. Install equipment in accordance with the U.S. National Electrical

Code, all local codes and the manufacturer’s recommendations.

8.c. Ground the equipment in accordance with the U.S. National

Electrical Code and the manufacturer’s recommendations.

()(461

+662999.,0&1.0(.(&64,&&1/5$)(6;

)14$'',6,10$.5$)(6;,0)14/$6,10

SAFETY

Weld ng Safety

Interact ve Web Gu de

for mob le dev ces

&(K+*%$))T(*K

Pour votrepropreprotectionlireetobservertouteslesinstructions

et les précautions de sûreté specifiques qui parraissent dans ce

manuelaussibienqueles précautionsdesûretégénéralessuiv-

antes:

)MB5DL&?EB)?E4175"VB3

1. Protegez-vouscontrelasecousseélectrique:

a. Les circuits à l’électrode et à la piéce sont sous tension

quandlamachineàsouderestenmarche.Evitertoujours

toutcontactentre lespartiessoustensionetlapeaunue

oulesvétementsmouillés.Porterdesgantssecsetsans

trouspourisolerlesmains.

b. Fairetrésattentiondebiens’isolerdelamassequandon

soudedansdes endroits humides, ou sur un plancher

metalliqueoudesgrillesmetalliques,principalementdans

lespositionsassisoucouchépourlesquellesunegrande

partieducorpspeutêtreencontactaveclamasse.

c. Maintenir le porte-électrode, la pince de masse, le câble

de soudage et la machine à souder en bon et sûr état

defonctionnement.

d.Ne jamais plonger le porte-électrode dans l’eau pour le

refroidir.

e.Nejamaistouchersimultanémentlespartiessoustension

desporte-électrodesconnectésàdeuxmachinesàsouder

parce que la tension entre les deux pinces peut être le

totaldelatensionàvidedesdeuxmachines.

f. Si on utilise la machine à souder comme une source de

courantpoursoudagesemi-automatique, ces precautions

pour le porte-électrode s’applicuent aussi au pistolet de

soudage.

2. Danslecasdetravailaudessusduniveaudusol,seprotéger

contreleschutesdanslecasouonrecoitunchoc.Nejamais

enrouler le câble-électrode autour de n’importe quelle partie

ducorps.

3. Un coup d’arc peut être plus sévère qu’un coup de soliel,

donc:

a. Utiliser un bon masque avec un verre filtrant approprié

ainsiqu’unverreblancafindeseprotégerlesyeuxduray-

onnement de l’arc et des projections quand on soude ou

quandonregardel’arc.

b.Porterdes vêtements convenables afin de protégerla

peau de soudeur et des aides contre le rayonnement de

l‘arc.

c.Protégerl’autrepersonneltravaillantàproximitéau

soudageàl’aided’écransappropriésetnon-inflammables.

4.Desgouttesdelaitierenfusionsontémisesdel’arc de

soudage.Seprotégeravecdesvêtementsdeprotectionlibres

de l’huile, tels que les gants en cuir, chemise épaisse, pan-

talonssansrevers,etchaussuresmontantes.

5. Toujours porter des lunettesdesécuritédanslazonede

soudage. Utiliser des lunettes avec écrans lateraux dans les

zonesoùl’onpiquelelaitier.

6. Eloigner les matériaux inflammables ou les recouvrir afin de

prévenirtoutrisqued’incendiedûauxétincelles.

7. Quandonnesoudepas,poserlapinceàuneendroitisoléde

la masse. Un court-circuit accidental peut provoquer un

échauffementetunrisqued’incendie.

8. S’assurer que la masse est connectée le plus prés possible

delazonedetravailqu’ilestpratiquedelefaire.Sionplace

la masse sur la charpente de la construction ou d’autres

endroitséloignésdelazonedetravail,onaugmentelerisque

devoirpasserlecourantdesoudageparleschainesdelev-

age, câbles de grue, ou autres circuits. Cela peut provoquer

desrisquesd’incendieoud’echauffementdeschainesetdes

câblesjusqu’àcequ’ilsserompent.

9. Assurer une ventilation suffisante dans la zone de soudage.

Ceciest particuliérement important pour lesoudage de tôles

galvanisées plombées, ou cadmiées ou tout autre métal qui

produitdesfumeéstoxiques.

10.Nepas souder en présence de vapeursdechlore provenant

d’opérations de dégraissage, nettoyage ou pistolage. La

chaleuroulesrayonsdel’arcpeuventréagiraveclesvapeurs

dusolvantpourproduireduphosgéne(gasfortementtoxique)

ouautresproduitsirritants.

11. Pour obtenir de plus amples renseignements sur la sûreté,

voir le code “Code for safety in welding and cutting” CSA

StandardW117.2-1974.

&(K+*%$))T(*K&%+(

")#$)Q)%+(Q

*($)%(#*+(*Q

(())+(

1. Relieràlaterrelechassisduposteconformementaucodede

l’électricitéetauxrecommendationsdufabricant.Ledispositif

de montage ou la piece à souder doit être branché à une

bonnemiseàlaterre.

2. Autantquepossible,I’installationetl’entretienduposteseront

effectuésparunélectricienqualifié.

3. Avantdefairesdestravauxàl’interieurdeposte,ladebranch-

eràl’interrupteuràlaboitedefusibles.

4. Garder tous les couvercles et dispositifs de sûreté à leur

place.

SAFETY

*"%%$*$*)

Page

________________________________________________________________________

>CD1<<1D9?> )53D9?>

TechnicalSpecifications ........................................................................................A-1

GeneralDescription...............................................................................................A-2

DesignFeatures ....................................................................................................A-2

Pre-OperationInstallation......................................................................................A-3

SafetyPrecautions ..........................................................................................A-3

ExhaustSparkArrester ...................................................................................A-3

Location/Ventilation.........................................................................................A-3

AngleofOperation ..........................................................................................A-4

MachineGrounding.........................................................................................A-4

LiftBail ............................................................................................................A-4

Trailers ............................................................................................................A-4

VehicleMounting.............................................................................................A-5

PolarityControlandCableSizes ....................................................................A-5

Pre-OperationService ...........................................................................................A-5

Oil,Fuel...........................................................................................................A-5

CoolingSystem ...............................................................................................A-5

BatteryCharging .............................................................................................A-6

ElectricalDevicesusewiththisProduct..........................................................A-7

________________________________________________________________________

%@5B1D9?> )53D9?>

EngineOperation...................................................................................................B-1

StartingThePerkinsEngine ...........................................................................B-1

ighAltitudeOperation,Stoppingtheengine .................................................B-1

EngineBreak-In ..............................................................................................B-2

WelderOperation...................................................................................................B-2

DutyCycle.......................................................................................................B-2

CurrentControl................................................................................................B-2

owtoSetControlsforStickWelding ............................................................B-3

GasShieldingFluxCoreWelding ...................................................................B-4

IdlerOperation,AuxiliaryPower,FuelConsumptionData..............................B-4

________________________________________________________________________

335CC?B95C)53D9?>

OptionalFeatures(FieldInstalled) ........................................................................C-1

________________________________________________________________________

#19>D5>1>35 )53D9?>

SafetyPrecautions ................................................................................................D-1

GeneralInstructions ..............................................................................................D-1

CoolingSystem .....................................................................................................D-1

Bearings ................................................................................................................D-1

CommutatorandBrushes .....................................................................................D-1

IdlerMaintenance..................................................................................................D-2

Nameplates ...........................................................................................................D-2

PurgingAirfromFuelSystem................................................................................D-2

EngineServiceChart ............................................................................................D-3

GFCITestingandResettingProcedure ................................................................D-4

________________________________________________________________________

*B?E2<5C8??D9>7)53D9?>

SafetyPrecautions.................................................................................................E-1

WelderTroubleshooting ........................................................................................E-2

ElectronicIdlerTroubleshootingGuide...........................................................E-3,E-4

EngineTroubleshootingGuide ...............................................................E-5thruE-8

________________________________________________________________________

917B1=C )53D9?>

WiringDiagrams ....................................................................................................F-1

DimensionPrint......................................................................................................F-2

________________________________________________________________________

&1BDC"9CD&

________________________________________________________________________



$)*""*%$

)®



*$")&*%$))®

#1;5#?45< 5C3B9@D9?> )@554(&# 9C@<135=5>D )D1BD9>7 BI

)ICD5= 1@139D95C

3Cylinder 91.47cu.in

12VDCbattery

Fuel:16gal.

24.8 P(18.5kW) (1.5ltrs) (Group24,650 60.6L.

KUBOTANaturallyAspirated ighIdle1800 coldcrankamps)

D1503-M Water-Cooled LowIdle1440 ?B5H)DB?;5

1.4KW

Starter Oil:5.9Qtrs.

EPA DieselEngine FullLoad1800 5.6L.

Tier4 CastIronCylinder, 3.27”x3.64”

Compliant Block/Crankcase (83mmx92.4mm)

Coolant:7.82Qts.

7.4L.

40A.Alternator

w/builtinreg.

$&+*)"$$

(*%+*&+*NN-"(

#%" * -* &* -*

K3201-1 45.5in.(2) 24.3in. 62.8in. 1432lbs.

CSAWithout (1156mm) (616mm) (1594mm ) (650kg.)

WireFeedModule

K3201-2 45.5in.(2) 24.3in. 62.8in. 1465lbs.

CSAWith (1156mm) (616mm) (1594mm ) (665kg.)

WireFeedModule

(*%+*&+*NN$(*%(

)(&*%$ (*%+*&+* EDI

,%"*)(*#&) /"

300AmpDCWelder 30V@250A 100%

AllCopperWindings 32V@300A 60%

PureDCPowerGenerator 90VDCMax.OCV@1800RPM

EH9<91BI&?G5B

3,000WattsContinuous,60 zAC

26Amps@120V

13Amps@240V

&/)"#$)%$) 

*Basedona10min.period.

(1) Outputratinginwattsisequivalenttovolt-amperesatunitypowerfactor.Outputvoltageiswithin±10%atallloadsupto

ratedcapacity.Whenwelding,availableauxiliarypowerwillbereduced.

(2) eighttotopofexhaustelbow.

PANTONE 420C - SWATCH LIBRARY SOLID COATED



$)*""*%$

)®



$(")(&*%$

TheSAE-300®Eisaheavyduty,enginedriven,DC

arc welding power source, capable of providing con-

stantcurrentoutputforstickweldingorDCTIGweld-

ing. This welder is wound with all copper coils, rated

at 300 amps/32 Volts, and provides other Classic®

featuressuchasimproveddoorlatchesandstainless

hinges.WiththeadditionoftheoptionalK3964-1Wire

Feed Module™, the SAE-300®E will provide con-

stantvoltageoutputforrunningthe LN-7,LN-23P,or

LN-25wirefeeders.(TheWireFeedModuleisfactory

installed on the K3201-2). The optional K924-5

Remote Control Kit, provides a remote control rheo-

stat for remote fine current and open circuit voltage

adjustment.SeeSectionCfordescription.

The SAE-300®E has an Electronic Engine

Protection System. In the event of sudden low oil

pressure or high coolant temperature, the engine

immediately shuts down.  The SAE-300®E has a

currentrangeof40-350 DCamps withoutputratings

asfollows:

These units are also capable of providing 3 KVA of

120/240voltsof60cycleACauxiliarypower.

TheSAE-300®EusestheKubotaD1503-Mindustri-

alwater-cooleddieselengine.

)$*+()

?>DB?<&1>5<

Theweldercontrolsconsist ofaReactor anda“Fine

Current Adjustment” rheostat located on the upper

controlpanelatthe exciterendof themachine. The

lower control panel welder is equipped with a “Start”

button, an “Ignition” switch, an “Idler” control switch,

anda“GlowPlug”buttonforeasiercoldweatherstart-

ing.

Thelowercontrolpanelalsocontainsanenginetem-

perature gauge, a battery charging fault indicator, an

oilpressuregauge,afuel/hour/LEDindicator

gauge, temperature gauge, for auxiliary power con-

sistsofone20amp,120VAC(5-20R)duplexrecepta-

clewithGFCIprotectionandone15amp,240VAC(6-

15R)receptacle,protectedby2pole,15Ampbreak-

er.

<<?@@5B-9>49>7C -Forlonglifeanddependable

operation.

>79>54<5B -TheSAE-300®Eisequippedwithan

electronic automatic engine idler.  It automatically

increasesanddecreasesenginespeedwhenstarting

andstoppingweldingorusingauxiliarypower.

A built-in time delay permits changing electrodes

beforetheengineslowstoitslowidlespeed.

The“Idler” control switch on thepanellocksthe idler

inhighidlepositionwhendesired.

EH9<91BI &?G5B - 3.0 KVA of nominal 120/240V,

60 z,AC.Outputvoltageismaintainedwithin±10%

at all loads up to rated capacity.  (See Optional

FeaturesSectionCforPowerPlugKit.)

Protectsthe20amp,120Vduplexreceptacle.

See the #19>D5>1>35)53D9?> for detailed informa-

tionontestingandresettingoftheGFCI.

,+&".(&*"$

AGFCIprotectsthe120Vauxiliarypower

receptacle.

A GFCI (Ground Fault Circuit Interrupter) is a device to

protectagainstelectricshockshouldapieceofdefective

equipmentconnectedtoitdevelopagroundfault.Ifthis

situationshould occur, the GFCI will trip,removingvolt-

agefromtheoutputofthereceptacle.IfaGFCIistripped

seethe MAINTENANCEsection fordetailed information

on testing and resetting it. A GFCI should be properly

testedatleastonceeverymonth.

The 120 V auxiliary power receptacle should only be

used with three wire grounded type plugs or approved

double insulated tools with two wire plugs. The current

ratingofanyplugusedwiththesystemmustbeatleast

equal to the current capacity of the associated recepta-

cle.

250A@30V

300A@32V

100%

60%

(*%+*&+* +*//"



$)*""*%$

)P



-5<45B>3<?CEB5 - The complete welder is rubber

mountedonaruggedsteel“C”channelbase.

The output terminals are placed at the side of the

machinessothattheyareprotectedbythedoor.The

outputterminalsarelabeled(+)and(-).

B1>;9>7)ICD5= - A 12 volt electric starter is stan-

dard.

9B<51>5B - eavydutytwostagedrytype.

#E66<5B -A muffler and stainlesssteelexhaustoutlet

elbowarestandard.

E5<?EB"71E75 -Ametertorecordhoursof

operation,showfuelstatus,batterychargingfaultLED

andenginefaultLED.

>79>5 &B?D53D9?>The system shuts the engine

downin theevent ofsuddenlow oilpressureor high

coolant temperature. A warning light on the control

panelwillindicatesuchafault.Toresettheenginefor

restarting,turntheignitionswitchoffthenon.Referto

Troubleshooting section for all warning light fault

codes.

1DD5BI81B79>7"978DAwarningindicatorlightfor

Low/Nobatterycharge.Thelightisoffwhenthesys-

temsarefunctioningproperly.Thelightwillcomeonif

there is a Low/No battery condition but the machine

willcontinuetorun.

$%*: The light will come on when the Run/Stop

switch is in the “ON” position. It will come on during

cranking and stay on until the engine starts. After,

starting the engine the light will go off unless a

Low/Nobatteryconditionexists.

%9< B19> ,1<F5 A ball valve, hose and clamp are

standard.

(5=?D5 ?>DB?< - The Remote / Local Switch and

Receptaclearestandard.

&(%&(*%$$)*""*%$

.+)*)&(!(()*(

Some federal, state or local laws may require that

engines be equipped with exhaust spark arresters

when they are operated in certain locations where

unarrested sparks may present a fire hazard.  The

standard muffler included with this welder does not

qualify as a spark arrester.  When required by local

regulations,asuitablesparkarrestermustbeinstalled

andproperlymaintained.

Useofanincorrectarrestermayleadtoenginedamage

or performance loss.  Contact the engine manufacturer

forspecificrecommendations.



"%*%$,$*"*%$

Always operate the welder with the doors closed.

Leavingthedoorsopenchangesthedesignedairflow

andmaycauseoverheating.

Theweldershouldbelocatedtoprovideanunrestrict-

edflow ofclean,cool air.Also, locatethewelder so

that engine exhaust fumes are properly vented to an

outsidearea.

? >?D 1DD5=@D D? EC5D89C5AE9@=5>D E>D9< I?E

81F5D8?B?E78<IB514 D85 5>79>5=1>E613DEB5BVC

=1>E1< CE@@<954G9D8 I?EBG5<45BD 9>3<E45C

9=@?BD1>D C165DI @B531ED9?>C 45D19<545>79>5

CD1BD9>7 ?@5B1D9>7 1>4 =19>D5>1>359>CDBE3D9?>C

1>4@1BDC<9CDC

"*()%!31>;9<<

O?>?DD?E385<53DB931<<I<9F5@1BDC?B

5<53DB?45G9D8C;9>?BG5D3<?D89>7

O>CE<1D5 I?EBC5<6 6B?= G?B; 1>4

7B?E>4

O<G1ICG51B4BI9>CE<1D9>77<?F5C

$$U.+)*U31>;9<<

O+C59>?@5> G5<<F5>D9<1D54 1B51C?B

F5>D5H81ECD?EDC945

#%,$&(*)U31>9>:EB5

O? >?D ?@5B1D5G9D8 4??BC?@5> ?B

7E1B4C?66

O)D?@5>79>5256?B5C5BF939>7

O!55@1G1I6B?==?F9>7@1BDC

)551449D9?>1<G1B>9>79>6?B=1D9?>1DD85

6B?>D?6D89C?@5B1D?BVC=1>E1<



-($$

+*%$

Andere Handbücher für SAE-300 HE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lincoln Electric Schweißsystem Handbücher

Lincoln Electric

Lincoln Electric SP-100T Bedienungsanleitung

Lincoln Electric

Lincoln Electric SQUARE WAVE TIG 275 IM609-B Bedienungsanleitung

Lincoln Electric

Lincoln Electric COOLARC 46 Bedienungsanleitung

Lincoln Electric

Lincoln Electric Power Wave AC/DC 1000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric VANTAGE 300 IM992 Bedienungsanleitung

Lincoln Electric

Lincoln Electric IM610-A Bedienungsanleitung

Lincoln Electric

Lincoln Electric WELDMARK 135 PLUS IM767 Bedienungsanleitung

Lincoln Electric

Lincoln Electric Linc Feed 24M Bedienungsanleitung

Lincoln Electric

Lincoln Electric Idealarc 250 Bedienungsanleitung

Lincoln Electric

Lincoln Electric SEVERE DUTY SVM187-A Bedienungsanleitung

Lincoln Electric

Lincoln Electric Invertec V205 Bedienungsanleitung

Lincoln Electric

Lincoln Electric PIPELINER 200 Bedienungsanleitung

Lincoln Electric

Lincoln Electric 12881 Bedienungsanleitung

Lincoln Electric

Lincoln Electric FlexCut 125 CCC Bedienungsanleitung

Lincoln Electric

Lincoln Electric SAE-300 MP K4089-2 Bedienungsanleitung

Lincoln Electric

Lincoln Electric MAXsa 29 WIRE DRIVE Bedienungsanleitung

Lincoln Electric

Lincoln Electric STT-10 HEAD & CONTROLS BOOM MOUNT OR BENCH MODELS... Bedienungsanleitung

Lincoln Electric

Lincoln Electric LINCOLN WELDING ARMS IM886 Bedienungsanleitung

Lincoln Electric

Lincoln Electric PF41 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWERTEC 305S Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE STT Bedienungsanleitung

Lincoln Electric

Lincoln Electric MAGNUM IM887 Bedienungsanleitung

Lincoln Electric

Lincoln Electric SAF-FRO DIGISTEEL III 320C Bedienungs- und Wartungshandbuch

Lincoln Electric

Lincoln Electric POWERTEC i250C STANDARD Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Everlast

Everlast POWER MTS 221STi Bedienungsanleitung

Kipor

Kipor KDE180XW Bedienungsanleitung

OrienTek

OrienTek T40 Bedienungsanleitung