Lincoln Electric SAF-FRO PRESTOTIG 200 AC/DC Bedienungsanleitung

IM3106

10/2022

REV05

PRESTOTIG 200 AC/DC

OPERATOR’S MANUAL

ENGLISH

Lincoln Electric Bester Sp. z o.o.

ul. Jana III Sobieskiego 19A, 58-260 Bielawa, Poland

English English

12/05

THANKS! For having chosen the QUALITY of the Lincoln Electric products.

Please Examine Package and Equipment for Damage. Claims for material damaged in shipment must be notified

immediately to the dealer.

For future reference record in the table below your equipment identification information. Model Name, Code & Serial

Number can be found on the machine rating plate.

Model Name:

………………...…………………………….…………………………………………………………………………………………..

Code & Serial number:

………………….……………………………………………….. …………………………………………………….……………..

Date & Where Purchased:

…………………………………………………………………... ……………………….…………………………………………..

ENGLISH INDEX

Technical Specifications...............................................................................................................................................................1

ECO design information ...............................................................................................................................................................2

Electromagnetic Compatibility (EMC) ..........................................................................................................................................4

Safety............................................................................................................................................................................................5

Introduction...................................................................................................................................................................................7

Installation and Operator Instructions ..........................................................................................................................................7

WEEE .........................................................................................................................................................................................25

Spare Parts.................................................................................................................................................................................25

REACh........................................................................................................................................................................................25

Authorized Service Shops Location...........................................................................................................................................25

Electrical Schematic ...................................................................................................................................................................25

Suggested Accessories..............................................................................................................................................................26

English 1 English

Technical Specifications

NAME INDEX

PRESTOTIG 200 AC/DC W000404213

INPUT

Input Voltage U1EMC Class Frequency

115 - 230Vac ± 15% A 50/60 Hz

Input Line Mode 20% 35% 60% 100% Input Amperes I1max PFmax

115Vac

STICK 3.2 kW 1.9 kW 1.4 kW

30 A 0.93

TIG DC 2.4 kW 1.8 kW 1.4 kW

STICK AC 3.2 kW 2.0 kW 1.5 kW

TIG AC 2.6 kW 2 kW 1.6 kW

Input Line Mode 30% 35% 60% 100%

230Vac

STICK 5.5 kW 3.7 kW 2.9 kW

27,2 A 0.88

TIG DC 4.8 kW 3.7 kW 2,8 kW

STICK AC 5.5 kW 3.9 kW 3.0 kW

TIG AC 5.0 kW 4.0 kW 3,2 kW

RATED OUTPUT

Output Current I2 Duty Cycle at % Output Voltage U2 Duty Cycle at %

Input Line Mode 20% 35% 60% 100% 20% 35% 60% 100%

115Vac 1ph

STICK DC 100A 60A 45A 24V 22.4V 21.8V

TIG DC 115A 90A 70A 14.6V 13.6V 12.8V

STICK AC 100A 60A 45A 24V 22.4V 21.8V

TIG AC 115A 90A 70A 14.6V 13.6V 12.8V

Input Line Mode 30% 35% 60% 100% 30% 35% 60% 100%

230Vac 1ph

STICK DC 160A 115A 95A 26.4V 24.6V 23.8V

TIG DC 200A 165A 130A 18V 16.6V 15.2V

STICK AC 160A 115A 95A 26.4V 24.6V 23.8V

TIG AC 200A 165A 130A 18V 16.6V 15.2V

OUTPUT RANGE

Welding Current Range Maximum Open Circuit Voltage OCV U0

2 – 200A 109 Vdc

RECOMMENDED INPUT CABLE AND FUSE SIZES

Fuse (time delayed) or Circuit Breaker Size Input Power Cable

16A@115Vac – 16A@ 230Vac 3x2.5mm2

DIMENSIONS AND WEIGHT

Height Width Length Net Weight

419 mm 246 mm 506 mm 23 kg

Operating Temperature Storage

Temperature

Operating Humidity

(t=20°C) Protection Degree

-10°C to +40°C -25°C to 55°C Not Applicable IP23

English 2 English

ECO design information

The equipment has been designed in order to be compliant with the Directive 2009/125/EC and the Regulation

2019/1784/EU.

Efficiency and idle power consumption:

Index Name Efficiency when max power consumption

/ Idle power consumption Equivalent model

W000404213 PRESTOTIG 200 AC/DC 80% / 21W No equivalent model

Idle state occurs under the condition specified in below table

IDLE STATE

Condition Presence

MIG mode

TIG mode X

STICK mode X

After 30 minutes of non-working X

Fan off X

The value of efficiency and consumption in idle state have been measured by method and conditions defined in the product

standard EN 60974-1:20XX.

Manufacturer’s name, product name, code number, product number, serial number and date of production can be read from

rating plate.

XXXXXXXXXX

Code: XXXXX XXXXXX-X

S/N: P1YYMMXXXXX

P1 YY MM XXXXX

5A5A 5B 5D5C

XXXXXXX

Where:

1- Manufacturer name and address

2- Product name

3- Code number

4- Product number

5- Serial number

5A- country of production

5B- year of production

5C- month of production

5D- progressive number different for each machine

English 3 English

Typical gas usage for MIG/MAG equipment:

Material type

Wire

diameter

[mm]

DC electrode positive Wire Feeding

[m/min] Shielding Gas Gas flow

[l/min]

Current

[A]

Voltage

[V]

Carbon, low

alloy steel 0,9 ÷ 1,1 95 ÷ 200 18 ÷ 22 3,5 – 6,5 Ar 75%, CO225% 12

Aluminium 0,8 ÷ 1,6 90 ÷ 240 18 ÷ 26 5,5 – 9,5 Argon 14 ÷ 19

Austenic

stainless steel 0,8 ÷ 1,6 85 ÷ 300 21 ÷ 28 3 - 7 Ar 98%, O22% /

He 90%, Ar 7,5% CO22,5% 14 ÷ 16

Copper alloy 0,9 ÷ 1,6 175 ÷ 385 23 ÷ 26 6 - 11 Argon 12 ÷ 16

Magnesium 1,6 ÷ 2,4 70 ÷ 335 16 ÷ 26 4 - 15 Argon 24 ÷ 28

Tig Process:

In TIG welding process, gas usage depends on cross-sectional area of the nozzle. For commonly used torches:

Helium: 14-24 l/min

Argon: 7-16 l/min

Notice: Excessive flow rates causes turbulence in the gas stream which may aspirate atmospheric contamination into the

welding pool.

Notice: A cross wind or draft moving can disrupt the shielding gas coverage, in the interest of saving of protective gas use

screen to block air flow.

End of life

At end of life of product, it has to be disposal for recycling in accordance with Directive 2012/19/EU (WEEE), information

about the dismantling of product and Critical Raw Material (CRM) present in the product, can be found at

https://www.lincolnelectric.com/en-gb/support/Pages/operator-manuals-eu.aspx

English 4 English

Electromagnetic Compatibility (EMC)

01/11

This machine has been designed in accordance with all relevant directives and standards. However, it may still generate

electromagnetic disturbances that can affect other systems like telecommunications (telephone, radio, and television) or

other safety systems. These disturbances can cause safety problems in the affected systems. Read and understand this

section to eliminate or reduce the amount of electromagnetic disturbance generated by this machine.

This machine has been designed to operate in an industrial area. The operator must install and operate this

equipment as described in this manual. If any electromagnetic disturbances are detected the operator must put

in place corrective actions to eliminate these disturbances with, if necessary, assistance from Lincoln Electric.

The Class A equipment is not intended for use in residential locations where the electrical power is provided by

the public low-voltage supply system. There may be potential difficulties in ensuring electromagnetic compatibility in those

locations, due to conducted as well as radiated disturbances. Provided that the public low voltage system impedance at the

point of common coupling is lower than 83 mΩ(or the short circuit power is higher than 0,6 MVA), this equipment is

compliant with IEC 61000-3-11 and IEC 61000-3-12 and can be connected to public low voltage systems. It is the

responsibility of the installer or user of the equipment to ensure, by consultation with the distribution network operator if

necessary, that the system impedance complies with the impedance restrictions.

Before installing the machine, the operator must check the work area for any devices that may malfunction because of

electromagnetic disturbances. Consider the following.

Input and output cables, control cables, and telephone cables that are in or adjacent to the work area and the machine.

Radio and/or television transmitters and receivers. Computers or computer controlled equipment.

Safety and control equipment for industrial processes. Equipment for calibration and measurement.

Personal medical devices like pacemakers and hearing aids.

Check the electromagnetic immunity for equipment operating in or near the work area. The operator must be sure that

all equipment in the area is compatible. This may require additional protection measures.

The dimensions of the work area to consider will depend on the construction of the area and other activities that are

taking place.

Consider the following guidelines to reduce electromagnetic emissions from the machine.

Connect the machine to the input supply according to this manual. If disturbances occur if may be necessary to take

additional precautions such as filtering the input supply.

The output cables should be kept as short as possible and should be positioned together. If possible connect the work

piece to ground in order to reduce the electromagnetic emissions. The operator must check that connecting the work

piece to ground does not cause problems or unsafe operating conditions for personnel and equipment.

Shielding of cables in the work area can reduce electromagnetic emissions. This may be necessary for special

applications.

WARNING

The Class A equipment is not intended for use in residential locations where the electrical power is provided by the public

low-voltage supply system. There can be potential difficulties in ensuring electromagnetic compatibility in those locations,

due to conducted as well as radio-frequency disturbances.

English 5 English

Safety

01/11

WARNING

This equipment must be used by qualified personnel. Be sure that all installation, operation, maintenance and repair

procedures are performed only by qualified person. Read and understand this manual before operating this equipment.

Failure to follow the instructions in this manual could cause serious personal injury, loss of life, or damage to this equipment.

Read and understand the following explanations of the warning symbols. Lincoln Electric is not responsible for damages

caused by improper installation, improper care or abnormal operation.

WARNING: This symbol indicates that instructions must be followed to avoid serious personal injury, loss

of life, or damage to this equipment. Protect yourself and others from possible serious injury or death.

READ AND UNDERSTAND INSTRUCTIONS: Read and understand this manual before operating this

equipment. Arc welding can be hazardous. Failure to follow the instructions in this manual could cause

serious personal injury, loss of life, or damage to this equipment.

ELECTRIC SHOCK CAN KILL: Welding equipment generates high voltages. Do not touch the electrode,

work clamp, or connected work pieces when this equipment is on. Insulate yourself from the electrode,

work clamp, and connected work pieces.

ELECTRICALLY POWERED EQUIPMENT: Turn off input power using the disconnect switch at the fuse

box before working on this equipment. Ground this equipment in accordance with local electrical

regulations.

ELECTRICALLY POWERED EQUIPMENT: Regularly inspect the input, electrode, and work clamp

cables. If any insulation damage exists replace the cable immediately. Do not place the electrode holder

directly on the welding table or any other surface in contact with the work clamp to avoid the risk of

accidental arc ignition.

ELECTRIC AND MAGNETIC FIELDS MAY BE DANGEROUS: Electric current flowing through any

conductor creates electric and magnetic fields (EMF). EMF fields may interfere with some pacemakers,

and welders having a pacemaker shall consult their physician before operating this equipment.

CE COMPLIANCE: This equipment complies with the European Community Directives.

ARTIFICIAL OPTICAL RADIATION: According with the requirements in 2006/25/EC Directive and

EN 12198 Standard, the equipment is a category 2. It makes mandatory the adoption of Personal

Protective Equipments (PPE) having filter with a protection degree up to a maximum of 15, as required by

EN169 Standard.

FUMES AND GASES CAN BE DANGEROUS: Welding may produce fumes and gases hazardous to

health. Avoid breathing these fumes and gases. To avoid these dangers the operator must use enough

ventilation or exhaust to keep fumes and gases away from the breathing zone.

ARC RAYS CAN BURN: Use a shield with the proper filter and cover plates to protect your eyes from

sparks and the rays of the arc when welding or observing. Use suitable clothing made from durable

flame-resistant material to protect you skin and that of your helpers. Protect other nearby personnel with

suitable, non-flammable screening and warn them not to watch the arc nor expose themselves to the arc.

English 6 English

WELDING SPARKS CAN CAUSE FIRE OR EXPLOSION: Remove fire hazards from the welding area

and have a fire extinguisher readily available. Welding sparks and hot materials from the welding process

can easily go through small cracks and openings to adjacent areas. Do not weld on any tanks, drums,

containers, or material until the proper steps have been taken to insure that no flammable or toxic vapors

will be present. Never operate this equipment when flammable gases, vapors or liquid combustibles are

present.

WELDED MATERIALS CAN BURN: Welding generates a large amount of heat. Hot surfaces and

materials in work area can cause serious burns. Use gloves and pliers when touching or moving

materials in the work area.

CYLINDER MAY EXPLODE IF DAMAGED: Use only compressed gas cylinders containing the correct

shielding gas for the process used and properly operating regulators designed for the gas and pressure

used. Always keep cylinders in an upright position securely chained to a fixed support. Do not move or

transport gas cylinders with the protection cap removed. Do not allow the electrode, electrode holder,

work clamp or any other electrically live part to touch a gas cylinder. Gas cylinders must be located away

from areas where they may be subjected to physical damage or the welding process including sparks and

heat sources.

CAUTION: The high frequency used for contact-free ignition with TIG (GTAW) welding, can interfere with

the operation of insufficiently shielded computer equipment, EDP centers and industrial robots, even

causing complete system breakdown. TIG (GTAW) welding may interfere with electronic telephone

networks and with radio and TV reception.

NOISE APPEARES DURING WELDING CAN BE HARMFUL: Welding arc can cause noise with high

level of 85dB for 8-hour week day. Welders operating welding machines are obligated to wear the proper

ear protectors. Employers are obligated to carry examinations and measurements of health harmful

factors.

SAFETY MARK: This equipment is suitable for supplying power for welding operations carried out in an

environment with increased hazard of electric shock.

The manufacturer reserves the right to make changes and/or improvements in design without upgrade at the same time the

operator’s manual.

English 7 English

Introduction

General Description

PRESTOTIG 200 AC/DC machine is designated to

performe MMA (SMAW) and TIG (GTAW) welding

process in DC and AC current.

Unit is designed mainly to satisfy TIG requestes in both

DC and AC mode: thanks an advance menu options both

beginners and experts welder can adjust welding

parameters to have the best welding performances.

Following paragraphs will show how to access to the

menu and the parameters tha can be set.

The following equipment has been added to

PRESTOTIG 200 AC/DC:

HOSE CLAMP

GAS HOSE

MOUNT HOSE

NUT HALF BLIND 1/4F

MALE QUICK COUPLING HOSE

Recommended equipment, which can be bought by user,

was mentioned in the "Suggested Accessories " section.

Installation and Operator Instructions

Read this entire section before installation or operation of

the machine.

Location and Environment

This machine will operate in harsh environments.

However, it is important that simple preventative

measures are followed to assure long life and reliable

operation.

Do not place or operate this machine on a surface with

an incline greater than 15° from horizontal.

Do not use this machine for pipe thawing.

This machine must be located where there is free

circulation of clean air without restrictions for air

movement to and from the air vents. Do not cover the

machine with paper, cloth or rags when switched on.

Dirt and dust that can be drawn into the machine

should be kept to a minimum.

This machine has a protection rating of IP23. Keep it

dry when possible and do not place it on wet ground

or in puddles.

Locate the machine away from radio controlled

machinery. Normal operation may adversely affect

the operation of nearby radio controlled machinery,

which may result in injury or equipment damage.

Read the section on electromagnetic compatibility in

this manual.

Do not operate in areas with an ambient temperature

greater than 40°C.

Input Supply Connection

Check the input voltage, phase, and frequency supplied to

this machine before turning it on. The allowable input

voltage is indicated in the technical specification section of

this manual and on the rating plate of the machine. Be

sure that the machine is grounded.

Make sure the amount of power available from the input

connection is adequate for normal operation of the

machine. The fuse rating and cable sizes are both

indicated in the "Technical Specification" section of this

manual.

The machines are designed to operate on engine driven

generators as long as the auxiliary can supply adequate

voltage, frequency and power as indicated in the

"Technical Specification" section of this manual. The

auxiliary supply of the generator must also meet the

following conditions:

230Vac 1 phases:

Vac peak voltage: below 280V

Vac frequency: in the range of 50 and 60Hz

RMS voltage of the AC waveform: 230Vac ± 15%

115Vac 1 phases:

Vac frequency: in the range of 50 and 60Hz

RMS voltage of the AC waveform: 115Vac ± 15%

Note: if connected @ 115Vac the equipment has output

derating It is important to check these conditions because

many engine driven generators produce high voltage

spikes. Operation of this machine on engine driven

generators not conforming to these conditions is not

recommended and may damage the machine.

Caution: To provide fully performance of duty cycle You

need to change overcurrent protection for 25A type D and

change for a proper input plug (or connect directly to a

power network)

Example:

English 8 English

Output Connections

A quick disconnect system using Twist-Matecable

plugs is used for the welding cable connections. Refer to

the following sections for more information on connecting

the machine for operation of M welding (MMA) or TIG

welding (GTAW).

Table 1.

Quick Disconnect: Torch (for MMA and

GTAW process) output connector for the

welding circuit.

Quick Disconnect: workpiece output

connector for the welding circuit.

Stick Welding (MMA)

This machine does not include a MMA welding kit cables,

but may be purchased separately. Refer to the

accessories section for more information.

First determine the proper electrode polarity for the

electrode to be used. Consult the electrode data for this

information. Then connect the output cables to the output

terminals of the machine for the selected polarity. Shown

here is the connection method for torch.

Connect the electrode cable to the torch terminal and the

work clamp to the work piece terminal. Insert the

connector with the key lining up with the keyway and

rotate approximately ¼ turn clockwise. Do not over

tighten.

Polarity for Stick can be selected between (DC+, DC-, AC)

by front panel push button and menu, see following.

TIG Welding (GTAW)

This machine does not include a TIG torch necessary for

TIG welding, but one may be purchased separately.

Refer to the accessories section for more information.

Connect the torch cable to

the torch terminal of the

machine and the work

clamp to the work piece

terminal. Insert the

connector with the key

lining up with the keyway

and rotate approximately ¼ turn clockwise. Do not over

tighten. Finally, connect the gas hose from the TIG torch

to the gas connector (B) on the front of the machine. If

necessary, an extra gas connector for the fitting on the

front of the machine is included in the package. Next,

connect the fitting on the back of the machine to a gas

regulator on the cylinder of gas to be used. The required

fittings are included in the package. Connect the TIG

torch trigger to the trigger connector (A) on the front of the

machine.

TIG Welding with a Water Cooled Torch

A cooling unit can be applied to the Machine:

COOLARC-24

If a Coolarc unit listed above is connected to the Machine,

it will be automatically turned ON and OFF in order to

ensure the torch cooling. When Stick welding mode is

used the cooler will be OFF.

This machine does not include a cooled TIG torch, but

one may be purchased separately. Refer to the

accessories section for more information.

WARNING

The Machine is provided with an electrical connection for

the Coolarc unit on its rear side. This socket is ONLY for

the connection of the Coolarc unit listed above.

WARNING

Before connecting the cooler unit to the Machine and

operate, read and understand the Instruction Manual

supplied with the cooling unit.

WARNING

Connect and disconnect the cooler with the unit switched

OFF.

Remote Control Connection

Refer to the accessories section for a list of

remote controls. If a remote control is used, it

will be connected to the remote connector on

the front of the machine. The machine will

automatically detect the remote control, turn

on the REMOTE LED, and switch to remote control mode.

More information on this mode of operation will be given in

the next section.

Inhaltsverzeichnis

Andere Lincoln Electric Schweißsystem Handbücher

Lincoln Electric

Lincoln Electric FLEXTEC 450 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE S700 Bedienungsanleitung

Lincoln Electric

Lincoln Electric RANGER 305G EFI 12157 Bedienungsanleitung

Lincoln Electric

Lincoln Electric Cobramatic K2259-1 Bedienungsanleitung

Lincoln Electric

Lincoln Electric 13175 Bedienungsanleitung

Lincoln Electric

Lincoln Electric VRTEX 360 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V160 Bedienungsanleitung

Lincoln Electric

Lincoln Electric Tandem MIG High-Speed and High-Deposition... Bedienungsanleitung

Lincoln Electric

Lincoln Electric 11672 Bedienungsanleitung

Lincoln Electric

Lincoln Electric LF-72/74 Bedienungsanleitung

Lincoln Electric

Lincoln Electric CLASSIC 300 D PERKINS Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V160-S Bedienungsanleitung

Lincoln Electric

Lincoln Electric VRTEXTM 360 SVM200-A Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO IM708 Bedienungsanleitung

Lincoln Electric

Lincoln Electric Prism 4 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V200-T Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWERFEED IM827-D Bedienungsanleitung

Lincoln Electric

Lincoln Electric SAE-400 SEVERE DUTY IM727 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC 400TPX Bedienungsanleitung

Lincoln Electric

Lincoln Electric WELD-PACK 100 PLUS IM546 Bedienungsanleitung

Lincoln Electric

Lincoln Electric WELDLINE WTT2 20W Bedienungsanleitung

Lincoln Electric

Lincoln Electric K113 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWERTEC 305C PRO Bedienungsanleitung

Lincoln Electric

Lincoln Electric 12674 Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Everlast

Everlast POWER MTS 221STi Bedienungsanleitung

Kipor

Kipor KDE180XW Bedienungsanleitung

OrienTek

OrienTek T40 Bedienungsanleitung