Lincoln Electric VIKING ArcSpecs Bedienungsanleitung

GRAPHICS MAY VARY

Operator’s Manual

VIKING

™

ArcSpecs

™

Auto-Darkening Welding Goggles

with 4C

™

Technology

www.lincolnelectric.com/register

Authorized Service and Distributor Locator:

www.lincolnelectric.com/locator

Save for future reference

Date Purchased

Code: (ex: 10859)

Serial: (ex: U1060512345)

IM10544 | Issue Date Aug-19

TABLE OF CONTENT Page

SAFETY WARNINGS – READ BEFORE USING 1

WELDING GOGGLE INFORMATION 2

SPECIFICATIONS 3

OPERATING INSTRUCTIONS 4

GOGGLE OPERATIONS/FEATURES 5

GRIND BUTTON OPERATION 8

GOGGLE CARE AND MAINTENANCE 9

SHADE GUIDE SETTINGS 14

TROUBLESHOOTING 15

WARRANTY INFORMATION 16

REPLACEMENT PARTS, OPTIONAL ACCESSORIES 16

SAFETY WARNINGS – READ BEFORE USING

ARC Rays can injure eyes and burn skin

• Before welding, always inspect goggle and filter lens to be sure they are fitted

properly, in good condition and not damaged.

• Check to see that the clear lens is clean and securely attached to the goggles.

• Always wear safety glasses or goggles under the welding goggles and protec-

tive clothing to protect your skin from radiation, burns and spatter.

• Ensure that optical radiation from other welder's arcs in the immediate area

does not enter in from behind the goggles and auto-darkening filter.

Note: Auto-darkening filters in Lincoln goggles are designed to protect the user against harmful

ultra-violet and infrared rays both in the dark and light states. No matter what shade the filter is

set to, the UV/IR protection is always present.

FUMES AND GASES can be dangerous to your health.

• Keep your head out of fumes.

• Use enough ventilation or exhaust at the arc or both to keep fumes and gases

from your breathing zone and general area.

• When welding with electrodes which require special ventilation such as

stainless or hard facing (see instructions on container or MSDS) or on

lead or cadmium plated steel and other metals or coatings which

produce highly toxic fumes, keep exposure as low as possible and within

applicable OSHA PEL and ACGIH TLV limits using local exhaust or

mechanical ventilation. In confined spaces or in some circumstances,

outdoors, a respirator may be required. Additional precautions are also

required when welding on galvanized steel.

WARNING

Refer to http://www.lincolnelectric.com/safety

for additional safety information.

WELDING GOGGLE INFORMATION

This Auto-Darkening Welding Goggle will automatically change from a light

state (shade 3.5) to a dark state (Shade 5-13) when arc welding starts.

The filter automatically returns to a light state when the arc stops.

Match your welding application to the shade indicated on the shade chart.

(See Page 6)

• Operating temperature: 14°F ~ 131°F (-10°C ~ 55°C).

• Do not use or open the auto-darkening filter if damaged by shock,

vibration or pressure.

• Keep the sensors and solar cell clean. Clean the goggle filter using soapy

water solution and soft cloth which should be damp but not saturated.

This Auto-Darkening Welding Goggle is designed for use with GMAW,

GTAW, SMAW welding, or Plasma Arc and air carbon cutting.

The goggles provide protection from harmful UV and IR radiation, in both

dark and light states.

The goggles contain four sensors to detect the light from the welding arc, re-

sulting in the lens darkening to a selected welding shade.

• Do not use solvents or abrasive cleaning detergent.

• If cover lens is spattered or covered with dirt, it should be replaced

immediately.

• Use only replacement parts specified in this manual.

• Do not use the goggles without inside and outside cover lenses properly

installed.

SPECIFICATIONS

Optical Class 1/1/1/1

LCD Viewing Area 47.0 sq. cm. (7.29 sq. in.)

Goggle Size 187 x 75 x 82mm (7.4 x 2.9 x 3.2in.)

UV/IR Protection Up to Shade DIN 16 at all times

Arc Sensors 4

Light State Shade DIN 3.5

Variable Welding Shades DIN 5 to 13

Shade Control Digital Display Control,

Variable Shade

Power Supply Solar cell with battery assist

Grind Warning Internal Green Light

Battery CR2450 Lithium (1 Required)

Power On/Off Fully automatic

Light to Dark Switching Time 0.00004 sec. (1/25,000 sec.)

Dark to Light Switching Time Variable 0 to 9 (0.1 to 1.0 sec.),

Digital Display Control

Sensitivity Control

Variable 0 to 9, Digital Display Control

TIG Rating DC≥2 amps; AC≥2 amps

Operating Temperature 14°F ~ 131°F (-10°C ~ 55°C)

Storage Temperature -4° ~ 158°F (-20°C ~ 70°C)

Total Weight 335g (11.8 Oz.)

Compliance ANSI Z87.1, CSA 94.3

OPERATING INSTRUCTIONS

HEADBAND ADJUSTMENT: Headband Tightness is adjusted by loosening

or tightening the elastic band about the two adjustment clips.

HEADBAND REMOVAL: Locate the hinges on the Auto-Darkening Goggle

and pull the hard plastic connection of the headband toward the opening in

the hinge. To insert a new headband simply snap the connection back into

the opening of the hinge. See images showing Step 1 and Step 2 for a closer

view of the connection.

HEADCOVERING ADJUSTMENT: To adjust the headcovering about the

neck and lower face, locate the two straps on either side shown in the image

on the left. Pull the straps to the preferred tightness then use the hook and

loop fasteners to secure the fit as shown in the center and right images.

Step 1 Step 2

Hinge Hard Plastic

Connection

GOGGLE OPERATION/FEATURES

ON/MODE Button

•ON-OFF (Lens will automatically darken when arc is present)

The Auto-Darkening goggle will automatically turn on, the digital display

control will activate, and the goggles will be ready for use. It is

recommended that the user review the goggle settings prior to use. The

welding goggles will automatically turn off after a half hour of no use.

•MODE CONTROL

Short press of the ON/MODE

button to select the mode

appropriate for the work

activity:

Weld Mode − used for most

welding applications.

Push "FUNC" button to

adjust shade number,

sensitivity, and delay settings

before welding. In this mode,

the lens turns to dark

immediately when you start

welding.

Cutting Mode − used for

cutting applications.

Push "FUNC" button to adjust shade number, sensitivity, and delay

settings before cutting.

Grind Mode − used for grinding applications.

In this mode the lens shade is fixed shade No. 4. Shade number,

sensitivity, and delay settings cannot be adjusted when in grind mode.

Test Button

Press and hold test to preview shade selection before welding. When released

the viewing window will automatically return to the light state (3.5 Shade).

Battery Indicator

The symbol shows the current state of the battery. The volume of batteries

has four level symbols (See Figure 1). The symbol appears on the display

screen before 1 to 2 days of battery life remains, the CR2450 lithium battery

should be replaced at this time. The symbol of the Battery Indicator is not real-

time and is updated shortly after pushing the ON/MODE button.

Variable Shade Control

After turning on the lens, press the

"FUNC" button to choose "SHADE",

adjust the lens shade number. Use

the shade control UP and DOWN but-

tons to select the lens darkened

state.

The shade range for each mode is as

follows:

•

Weld Mode - No. 9 ~ No. 13

•

Cutting Mode - No. 5 ~ No. 8

•

Grind Mode - No. 4

Sensitivity Control

Press "FUNC" button to choose

"SENS". Use Sensitivity Control "UP"

and "DOWN" buttons to make the

lens more or less sensitive to arc light

for different welding processes. Sen-

sitivity settings 3 through 7 are the

normal settings for everyday use. The

sensitivity ranges for each mode are

as follows:

•

Weld Mode / Cutting Mode - No.

0 ~ No. 9

•

Grind Mode - No sensitivity

adjustment

It may be necessary to adjust goggle

sensitivity to accommodate different

lighting conditions or if the lens is flashing On and Off. Adjust the lens sensitivity

in lighting conditions the mask will be used in. Adjust mask sensitivity as follows:

•

Press the "DOWN" button to lower setting to 0.

•

Face the mask in the direction of use, exposing it to the surrounding light

conditions.

•

Press the "UP" button repeatedly until the lens darkens, then press the

"DOWN" button until the lens clears. The goggles are ready for use. Slight

readjustment may be necessary for certain applications or if the lens is

flashing on and off.

Delay Control

Press "FUNC" button to choose

"DELAY", begin lens delay adjust-

ments. Use the Lens Delay Con-

trol "UP" and "DOWN" buttons to

adjust the time for the lens to

switch to the clear state after

welding or cutting.

•

Weld Mode / Cutting Mode -

No. 0 ~ No. 9

•

Grind Mode - No Delay

Adjustment

The delay is particularly useful in eliminating bright after-rays present in higher

amperage applications where the molten puddle remains bright momentarily

after welding. Use the Lens Delay Control buttons to adjust delay from 0 to 9 (0.1

to 1.0 second). When welding ceases, the viewing window automatically

changes from the darkened state back to light state but with a pre-set delay to

compensate for any bright afterglow on the work piece. The delay time/response

can be set from 0 to 9. It is recommended to use a shorter delay with spot weld-

ing application and a longer delay with applications using higher current. Longer

delays can also be used for low current TIG welding in order to avoid the lens

lightening when the light path to the sensors is temporarily obstructed by a hand,

torch, etc.

GRIND BUTTON OPERATION

In order to switch the Auto Darkening Goggle from a Cutting or Welding

Shade into Grind Mode first locate the plastic button on the top and left side

of the Auto-Darkening Goggle. After the button has been located press and

hold it for 3 seconds. A green LED inside of the goggle should blink every 3

seconds after the button is pressed to indicate you are in Grind Mode. To

switch back to the previous Cutting or Welding shade simply press and hold

the button for 3 seconds. Grind mode is intended for grinding only not for

welding.

Inhaltsverzeichnis

Andere Lincoln Electric Schweißsystem Handbücher

Lincoln Electric

Lincoln Electric INVERTEC IM732-B Bedienungsanleitung

Lincoln Electric

Lincoln Electric Precision TIG 375 Bedienungsanleitung

Lincoln Electric

Lincoln Electric US-CW139 Bedienungsanleitung

Lincoln Electric

Lincoln Electric Lincolnweld 980 Bedienungsanleitung

Lincoln Electric

Lincoln Electric Invertec V160-T Bedienungsanleitung

Lincoln Electric

Lincoln Electric UWW-170 Bedienungsanleitung

Lincoln Electric

Lincoln Electric Vernon Tool MasterPipe Compact Profiler Handbuch

Lincoln Electric

Lincoln Electric VANTAGE 600 SD Bedienungsanleitung

Lincoln Electric

Lincoln Electric KA 1435 Bedienungsanleitung

Lincoln Electric

Lincoln Electric DC-650 PRO IM463-A Bedienungsanleitung

Lincoln Electric

Lincoln Electric VANTAGE 400-I Bedienungsanleitung

Lincoln Electric

Lincoln Electric Square Wave TIG 275 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC SVM129-B Bedienungsanleitung

Lincoln Electric

Lincoln Electric Power Feed 10R Bedienungsanleitung

Lincoln Electric

Lincoln Electric COUGAR K2704-2 Bedienungsanleitung

Lincoln Electric

Lincoln Electric SAF-FRO DIGISTEEL III 320C Bedienungs- und Wartungshandbuch

Lincoln Electric

Lincoln Electric CLASSIC 300 D PERKINS Bedienungsanleitung

Lincoln Electric

Lincoln Electric Vantage 566 Bedienungsanleitung

Lincoln Electric

Lincoln Electric WELDING POWER SOURCES AC-225-S Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWERTEC i250C STANDARD Bedienungsanleitung

Lincoln Electric

Lincoln Electric Invertec V155-S Bedienungsanleitung

Lincoln Electric

Lincoln Electric RANGER 10,000 PLUS Bedienungsanleitung

Lincoln Electric

Lincoln Electric 11400 Bedienungsanleitung

Lincoln Electric

Lincoln Electric PRO 155 Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Everlast

Everlast POWER MTS 221STi Bedienungsanleitung

Kipor

Kipor KDE180XW Bedienungsanleitung