Linde Ryval 400 aXe Bedienungsanleitung

Linde AG, Linde Gas Deutschland © Ryval 400-500 aXe MANUAL EN 02

MIG/MAG WELDING MACHINES

Ryval 400 aXe

Ryval 500 aXe

MINOR2 - MAJOR – SYNERGY

BASIC

INS RUC ION MANUAL

2 29

Linde AG, Linde Gas Deutschland ©

Content:

1. INTRODUCTION ............................................................................................. 3

2. SAFETY INSTRUCTIONS AND WARNINGS ....................................................... 4

3. CONDITIONS OF USE ...................................................................................... 7

4. TECHNICAL DATA ........................................................................................... 8

5. ACCESSORIES ............................................................................................... 10

6. DESCRIPTION OF THE APPLIANCE ................................................................. 11

7. GETTING STARTED ....................................................................................... 18

8. WELDING ..................................................................................................... 23

9. ROUTINE MAINTENANCE INSPECTION ...................................................... 27

10. STATEMENT OF WARRANTY ........................................................................ 28

11. DISPOSAL ..................................................................................................... 29

3 29

Linde AG, Linde Gas Deutschland ©

1. IN RODUC ION

Congratulations on your new Linde AG, Linde Gas Deutschland product. We

are proud to have you as our customer and will strive to provide you with the

best service and reliability in the industry.

This Operating Manual has been designed to instruct you on the correct use

and operation of your Linde AG, Linde Gas Deutschland product. Your

satisfaction with this product and its safe operation is our ultimate concern.

Therefore please take the time to read the entire manual, especially the

Safety Precautions. They will help you to avoid potential hazards that may

exist when working with this product.

Read and understand this entire Manual and your employer’s safety

practices before installing, operating, or servicing the equipment. While the

information contained in this Manual represents the Manufacturer's best

judgement, the Manufacturer assumes no liability for its use.

Ryval 400 500 aXe are three phase sturdy welding machines for MIG MAG

welding.

The machines are designed to produce maximum power output combined

with high reliability and efficiency.

The users interface is as simple as possible; however, there are secondary

parameters that can be set from the main front panel if suitable. All of them

are available in compact models, Ryval 400 and 500 can be ordered also as

sets consisting of the generator, interconnection cable bundle and separate

wire feeding unit. We will refer to the MINOR2-MAJOR and SYNERGY

controls as DIGITAL. The appliances can be both gas cooled or water

cooled.

CONTROL MODEL

BASIC

MINOR

MAJOR

SYNERGY

A + V meter

optional

YES

Wire initial speed (Soft Start)

YES

Advice of the parameter settings

YES

Electronic feedback of the wire

speed

NO YES YES YES

2 stoke 4 stroke

YES

Adjustable Post and Pre Gas

time

NO YES YES YES

Spot and Interval welding

YES

Adjustable Burn Bac

k Time

YES

4 29

Linde AG, Linde Gas Deutschland ©

2. SAFE Y INS RUC IONS AND WARNINGS

1. OPERATION AND MAINTENANCE OF WELDING EQUIPMENT CAN BE

DANGEROUS AND HAZARDOUS TO YOURHEALTH.

2. Arc welding produces intense electric and magnetic emissions that may

interfere with the proper function of cardiac pacemakers, hearing aids, or

other electronic health equipment. Persons who work near arc welding

applications should consult their medical health professional and the

manufacturer of the health equipment to determine whether a hazard

exists.

3. Once the packing has been opened, make sure that the machine is not

damaged. If in any doubt, call the service centre.

4. This equipment must only be used by qualified personnel.

5. During installation, any electric work must only be carried out by trained

personnel.

6. The machine must be used in a dry place with good ventilation.

7. Make sure that no metal dust can be drawn in by the fan inside the

machine, as this could cause damage to the electronic circuits.

8. It is prohibited to connect more than one generator in series or in parallel.

9. When installing the machine, follow the local regulations on safety.

10. The position of the machine must allow easy access by the operator to

the controls and connectors.

11. When the welding machine is operating, all its covers and doors must

be closed and well fixed.

12. Do not expose the welding machine to direct sunlight or to heavy rain.

This equipment conforms to protection rating IP23S.

13. The operator must wear gloves, clothes, shoes, and a helmet or a

welder’s helmet, which protect and are fire-resistant in order to protect him

against electric shock, flashes and sparks from cutting.

14. The operator must protect his eyes with safety visor or mask designed

for welding, fitted with standard safety filters. He should also be aware that

during arc welding ULTRAVIOLET RADIATION is emitted. Therefore it is

vital that his face is also protected from radiation. Ultraviolet rays produce

the same harmful effect as sun burning on unprotected skin.

15. The operator is obliged to warn anyone near the welding area of the

risks that welding involves and to arrange to provide adequate protection

equipment.

16. Keep all fumes and gases from the breathing area.

17. Keep your head out of the fume plume.

18. Use an air-supplied respirator if ventilation is not adequate to remove

all fumes and gases.

19. The kinds of fumes and gases from the plasma arc depend on the kind

of metal being used, coatings on the metal, and the different processes.

You must be very careful when welding any metals which may contain one

5 29

Linde AG, Linde Gas Deutschland ©

or more of the following:

Antimony Chromium Mercury

Nickel

Cobalt

Arsenic

Barium

Copper

Selenium

Beryllium

Lead

Silver

Cadmium

Manganese

Vanadium

20. Always read the Material Safety Data Sheets (MSDS) that should be

supplied with the material you are using. These MSDSs will give you the

information regarding the kind and amount of fumes and gases that may

be dangerous to your health.

21. It is very important to arrange for sufficient ventilation, especially when

welding in enclosed spaces. We suggest using suitable fume extractors to

prevent the risk of intoxication by fumes or gas generated by the welding

process.

22. Noise can cause permanent hearing loss. Welding arc processes can

cause noise levels to exceed safe limits. You must protect your ears from

loud noise to prevent permanent loss of hearing.

23. To protect your hearing from loud noise, wear protective ear plugs

and or ear muffs. Protect others in the workplace.

24. Noise levels should be measured to be sure the decibels (sound) do

not exceed safe levels.

25. The operator must ensure all flammable materials are removed from

the work area to avoid any risk of fire.

26. The operator must NEVER weld containers that have previously

contained petrol, lubricants, gas or similar flammable materials, even if the

container has been empty for a considerable time. THERE IS A VERY

HIGH RISK OF EXPLOSION.

27. The operator must be aware of all the special regulations which he

needs to conform to when cutting in enclosed spaces with a high risk of

explosion.

28. To prevent electric shock, we strongly suggest the following rules:

a) Do not work in a damp or humid environment.

b) Do not use the machine if its cables are damaged in any way.

c) Make sure that the earthing system of the electric equipment is

correctly connected and operational.

d) The operator must be insulated from the metal components

connected to the return wire.

e) The earthing of the piece being worked could increase the risk of

injury to the operator.

29. EN 60974-1 Standard: Open-circuit voltage. During the operation of

the machine, the highest voltage, with which it is possible to come into

contact, is the open-circuit voltage between the clamps.

30. The maximum open-circuit voltage of the plasma machines is

6 29

Linde AG, Linde Gas Deutschland ©

established by national and international standards (EN 60974-1)

depending on the type of current to be used, on its waveform and on the

hazards arising from the work place. These values are not applicable to

the strike currents and those for stabilisation of the arc that could be

above it.

31. The open-circuit voltage, for as many adjustments as possible, must

never exceed the values relating to the various cases shown in the

following table:

Case

Working conditions Open-circuit voltage

1 Places with increased

risk of electric shock

DC current: 113V

peak value

AC current: 68V

peak value and 48V

effective

2 Places without increased

risk of electric shock

DC current: 113V

peak value

AC current: 113V

peak value and 80V

effective

Torches held

mechanically with

increased protection for

the operator

DC current: 141V

peak value

AC current: 141V

peak value and

100V effective

4 Plasma cutting DC current: 500V

peak value

32. In case 1, the dc machines with rectifier must be built in such a way

that, in case of a fault developing in the rectifier (for example open circuit,

short circuit or lack of power), the permitted values cannot be exceeded.

The welding machines of this type can be marked with the symbol:

33. Before opening the machine switch off the machine and disconnect it

from the power socket.

34. Only personnel authorised by this company can carry out maintenance

on the machine.

PRO EC IVE U ILI IES

1. Welding helmet with filter shade at least 10

2. Welding gloves

3. Welding apron and cloth

4. Welding boots

RISK OVERVIEW

1. Risk of electric shock.

2. Ultraviolet light and light radiation

3. Risk of inhaling gas fumes and dust particles

4. Burns

7 29

Linde AG, Linde Gas Deutschland ©

5. Noise

NO E

1. It is forbidden to operate a machine with damaged insulation of the

welding torch or supply cable.

2. Never operate the machine taken down or damaged covers.

3. It is forbidden to operate the machine in wet environments and outdoors

in rain or snow.

4. Ensure proper grounding clamping pliers, which also reduces the risk of

electric shock.

5. Use prescribed protective utilities, keep them dry.

6. Arc welding produces intense electric and magnetic emissions that may

interfere with the proper function of cardiac pacemakers, hearing aids,

or other electronic health equipment. Persons who work near plasma

arc cutting applications should consult their medical health professional

and the manufacturer of the health equipment to determine whether a

hazard exists.

7. Never aim the torch against the eyes, body or other person.

3. CONDI IONS OF USE

1. This equipment must only be used by qualified personnel.

2. During installation, any electric work must only be carried out by trained

personnel.

3. Device complies with IEC 61000-3-12.

4. Do not expose the plasma machine to direct sunlight or to rain or snow.

This equipment conforms to protection rating IP23S.

5. Place the machine the way that the cooling air can enter the vents without

restriction to. It is necessary to ensure that no impurities, especially metal

particles, are not drawn into the machine.

6. Welding machine in terms of interference suppression is intended

primarily for industrial premises. In the case of use of other areas may be

need for special measures (see EN 60974-10).

7. The machine must be protected against

a) moisture and rain and snow

b) mechanical damage

c) draft and any ventilation of neighbouring machine

d) excessive overloading - crossing technical parameters

e) rough handling

8 29

Linde AG, Linde Gas Deutschland ©

ELEC ROMAGNE IC COMPA IBILI Y

The welding device is in terms of interference designed primarily for industrial

areas. It meets the requirements of EN 60974-10 class A and it isn’t

designed for using in residential areas, where the electrical energy is

supplied by public low-voltage power supply network. It can be here potential

problems with ensuring of electromagnetic compatibility in this areas, due to

interference caused by power lines as well as the radiated interference.

During operation, the device may be the source of interference.

Caution We warn users, that they are responsible for possible

interference from welding.

4. ECHNICAL DA A

Ryval 400 Ryval 500

Mains voltage V Hz 3x400 50 3x400 50

Mains protection A 20 @ 32 @

Max. input power I1 A 28,8 45,0

Max. effective current I1eff A 15,8 22,5

Welding current range A 55 - 420 70 - 530

Open-circuit voltage U20 V 19,3 - 48,0 20,2 - 59,8

Welding current (DC=100%) I2 A 260 330

Welding current (DC=60%) I2 A 300 390

Welding current (DC=x%) I2 A 30%=420 25%=530

Voltage steps

2 x 10 3 x 10

Insulation class

F F

Protection

IP 23S IP 23S

Standards

EN 60974-1, EN 60974-10 cl. A

Dimensions (w x l x h) mm 572x875x874 572x875x874

Weight compact GAS kg 120 155

Weight compact H2O kg 137 166

Weight Generator GAS kg 113 151

Weight Generator H2O kg 133 161

Wire speed Compact m min 1 - 19 1 - 19

Spool diameter Compact mm 300 300

Spool weight Compact kg 18 18

Cooling unit

Cooling power (Q=1l min) kW 0,74

Total liquid content l 3,5

Max. pressure Bar 3,5

9 29

Linde AG, Linde Gas Deutschland ©

Max. flow l min 8

Feeding unit PS aXe

Wire speed m min 1 - 19

Input voltage U1 V Hz 24 1~50

Input current I1 A 4

Welding current I2 (DC=100%) A 320

Welding current I2 (DC=60%) A 400

Spool diameter mm 300

Spool weight kg 18

Protection

IP 23S

Dimensions (w x l x h) mm 264x704x507

Weight (without wire and torch) Kg 22

Standards

EN 60974-5

Feeding unit FANFEED 40W SNEIL

Wire speed m min 1 - 25

Input voltage U1 V Hz 24 1~50

Input current I1 A 4

Welding current I2 (DC=100%) A 320

Welding current I2 (DC=60%) A 400

Spool diameter mm 300

Spool weight kg 18

Protection

IP 21S

Dimensions (w x l x h) mm 245x700x450

Weight (without wire and torch) Kg 18

Standards

EN 60974-5

10 29

Linde AG, Linde Gas Deutschland ©

5. ACCESSORIES

DELIVERED WI H HE MACHINE

1. Earthing cable 3m with a clamp

2. Feed roll 1,0 - 1,2mm

3. Gas hoses

4. By pass hose (just for H2O models)

5. Reduction for the wire spool

ACCESSORIES O ORDER

1. Wire cleaner

2. CO2 Gas pre heating cable

3. Reduction valve KU 5, K 2

4. Gas cylinder

5. Torch consumables

6. Earthing cable 4 - 5 m

7. Feed rolls 0,6-0,8 1,0-1,2 1,4-1,6 for carbon steels, aluminium, flux

core wires

8. Torches with UP-DOWN remote control

9. Welding torches (see the table below)

Torch type

Cooling

MB 36

Gas

MB 501 D

H2O

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Linde Schweißsystem Handbücher

Linde

Linde RYVAL 200 MIG MAN PFC Bedienungsanleitung

Linde

Linde BOC RAPTOR 250R MIG Bedienungsanleitung

Linde

Linde BOC Smootharc Advance II MIG 400R Bedienungsanleitung

Linde

Linde Ryval 181 BASIC aXe Bedienungsanleitung

Linde

Linde BOC RAPTOR 160 MIG Bedienungsanleitung

Linde

Linde BOC Smootharc Advance III MIG 225C Bedienungsanleitung

Linde

Linde BOC RAPTOR 135 Bedienungsanleitung

Linde

Linde BOC Smootharc Advance MIG 425R Bedienungsanleitung

Linde

Linde ARCLINE Cool 2 Bedienungsanleitung

Linde

Linde BOC Raptor CUT 30C Bedienungsanleitung

Linde

Linde BOC Smootharc MMA130VRD Bedienungsanleitung

Linde

Linde BOC Smoothcut 100A Bedienungsanleitung

Linde

Linde BOC RAPTOR Bedienungsanleitung

Linde

Linde Ryval 250 MIG MAN Bedienungsanleitung

Linde

Linde TPL 300 puls DC Bedienungsanleitung

Linde

Linde MSI 350 puls Kompakt Bedienungsanleitung

Linde

Linde Ryval 251 aXe Bedienungsanleitung

Linde

Linde Ryval 40 PLASMA PFC ovo Bedienungsanleitung

Linde

Linde BOC RAPTOR 200 MIG Bedienungsanleitung

Linde

Linde FSM-1 Bedienungsanleitung

Linde

Linde AGA Series Bedienungsanleitung

Linde

Linde BOC Smootharc Advance MIG 200C Bedienungsanleitung

Linde

Linde BOC Smootharc TIG200 DC Bedienungsanleitung

Linde

Linde BOC Smootharc MIG 250 Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung