Lindy 42624 Bedienungsanleitung

USB 3.0 KVM & Data Transfer Cable

User Manual English

Benutzerhandbuch Deutsch

Manuel Utilisateur Français

Manuale Italiano

No. 42624

www.lindy.com

Tested to Comply with

FCC Standards

For Home and Office Use!

User Manual English

Introduction

Thank you for purchasing the LINDY USB 3.0 KVM & Data Transfer Cable. This cable gives you the

ability to share Video, Keyboards & Mouse resources and transfer files between two Windows®

computers, via USB 3.0. Use Drag & Drop or Copy & Paste functionality via an easy to use GUI to

quickly move pictures, music, video and other files between computers at speeds of up to 5Gbps.

Control one computer from the other by simply moving your cursor from one screen to the other.

Touchscreen support means you can use touch enabled tablets, screens or monitors to switch between

compatible computers as you would use a mouse, while also maintaining the full resource and clipboard

sharing features of the cable.

Note – The cable has a limited performance when used with USB 2.0 host ports.

Package Contents



USB 3.0 KVM & Data Transfer Cable



Software CD



LINDY Manual

Features



Share Keyboards, Mice and Monitors between computers



Turn a Notebook / Desktop / Tablet PC into a 2nd display via Mirror & Extended display modes



Share Video Card & Hard Disk resources between two Windows computers



Easily transfer data, photos, music, and video between two computers



Conforms to SuperSpeed USB 3.0 (5Gbps) transfer rate



Support touch screen (Windows 8 or above)

Specification



Max Resolution 2048 x 1152 / 32bit



USB 3.0 Type-A Male connectors



USB 3.0 cable length 1.4m



Bus Powered



Operating Temperature: 0~50°C



Storage Temperature: -10~75°C



Humidity: <85% non-condensing



System Requirements



Available USB 2.0 / USB 3.0 port (USB 3.0 port is recommended)



CPU: Dual Core 2.0GHz or higher



RAM: 2GB memory or higher



Windows 8.1 / 8 / 7 / XP (32bit or 64bit)

User Manual English

Installation

!!! IMPORTANT!!!

DO NOT connect the LINDY USB 3.0 KVM & Data Transfer Cable to either computer until after

installing the included software and restarting both machines.

Installing the device driver from the Software Disc allows your computers to recognize the

LINDY USB 3.0 KVM & Data Transfer Cable. Please check your OS and refer to the appropriate

installation procedure below to begin installing the device drivers.

Windows 8.1 / 8 / 7 / XP

This section describes the driver installation procedure for a computer running Windows 7 OS.

Please ensure the USB 3.0 KVM & Data Transfer Cable is unplugged from your PC or Notebook before

continuing with the setup procedure.

•Insert the Software CD; the setup program should launch automatically, if it doesn’t launch, open

the Disc Drive folder via Windows Explorer and double click the Setup Application Icon.

•When the Windows User Account Control appears, click “Yes” to allow the program to install and

follow the Installation Wizard, click “Next” to continue.

•Once the installation is complete, close the Installer and Restart your computer.

•Repeat the driver installation on the second computer that you are going to use.

Note: You may notice your computer screens flashing or turning on & off during the installation; this is

normal and part of the installation process.

After finishing the driver installation on both computers and restarting, connect the USB 3.0 KVM & Data

Transfer Cable.

Windows 8.1 / 8 / 7

The device driver will be configured automatically. A Pop Up will appear on both computers. When this

completes the USB 3.0 KVM & Data Transfer Cable is ready to be used.

Windows XP

The Hardware Installation Wizard dialogue will show, select “No, not this time” and click “Next” to

continue.

User Manual English

Click “Continue Anyway” when the Microsoft Software warning dialogue box appears, then, click “Finish”

to complete the Hardware Wizard. A Pop Up will appear on both computers. When this completes the

LINDY USB 3.0 KVM & Data Transfer Cable is ready for use.

Uninstalling the Drivers

To uninstall the drivers, go to the Windows Control Panel and use the ‘Uninstall a Program’ feature.

•Locate the “MCT Dual System Swap (D.S.S.) 13.xx. Xxxx. 0186” (driver version may vary).

•Click the “Uninstall” button.

•Unplug the USB 3.0 KVM & Data Transfer Cable and click “OK” to continue.

•Select “Yes, I want to restart my computer now” and click “Finish” to reboot. After rebooting, you

will have completed the driver un-installation.

Connection Setup

The connectors of the USB 3.0 KVM & Data Transfer Cable are two different colours: Blue & Green.

These correspond to the colour of the User Interface (UI) icon that appear in your computer's toolbar and

help you identify the connected computer as you configure your system.

The following Settings are available and can be accessed on both Blue & Green computers. When you

first attach the cable the following dialogue will appear. The colour of the avatar icon will correspond to

end of the cable you have attached, Blue or Green.

User Manual English

Selecting the next icon on the first dialogue screen will open the ‘Display Share’ dialogue.

Here you can set the position of the second computer display; Left, Right, Above or Below. Selecting the

next icon will open the next ‘Display Share’ dialogue.

Here you can select the display mode (Extended or Mirror Mode)

Extended Mode - This feature allows you to use the connected computer's screen as an extended

display.

User Manual English

Mirror Mode - This feature allows the same contents to be displayed (mirrored) on both displays.

The screen resolution setting on the attached computer will follow the lead computer’s screen resolution.

For example, if this is 1024x768 at 32bit, then the mirrored computer will retain the same resolution.

Use your computers ‘Display Setting’s to change the resolution of the two screens as desired. The

Maximum Resolution the Cable supports is 2048 x 1152 / 32bit

Touch Screen Control (for Windows 8 or above)

If the computer has a touch screen, you can use that to directly control the computer being Mirrored or

Extended via the touch screen. This also applies to Tablets.

Save your settings by selecting the tick box in the bottom left of the screen. This will ensure you skip this

process the next time you connect the cable.

Selecting the next icon will open a final Information dialogue. You can choose not to see this Information

dialogue again by selecting the tick box in the bottom left of the screen.

Note – if you disconnect the cable at any time you should reconnect the appropriate Blue or Green end

to the computer it was attached to during setup. Swapping ends initialises a second install of the device

drivers and can cause malfunctions in the cables operation.

User Manual English

Operation

After finishing the Connection Setup, a new icon will appear in the System Tray of both machines.

Selecting this launches the Control Bar, which appears at the bottom right corner of both screens.

With the Control Bar you can control Display & Data Sharing Settings between the two computers.

Default Control Bar

Display Share - Select the Blue / Green icon to

view and control that computer.

Stop sharing displays – Select the Stop Icon.

Data Sharing - View and transfer data between

computers via GUI.

Clicking the “Folder” icon opens a file transfer GUI (Graphical User Interface) allowing you to transfer

files from one computer to the other.

User Manual English

The GUI supports File/Folder and Data transfer through the generic Drag & Drop or Copy & Paste

actions from the opposite computer at 5Gbps. Clipboard Sharing allows selected texts from the first

computer to be simply and easily pasted on the second, and vice versa.

Close Control Bar – Select the ‘X’ in the top right

corner of the Control Bar.

Reset Positions & Display Mode – Reset screen

positions and re-run the ‘Display Share’

dialogue.

Restart Control Bar - Double click the Control Bar icon on the task bar to restart the Control Bar.

Keyboard & Mouse Sharing - Move your Mouse cursor between the two computers to switch the

Keyboard usage to the other computer. I.e. Use the Keyboard of the first computer to type on the second

computer.

User Manual English

Troubleshooting

Known Issues

•Direct 3D is not supported under XP/Vista

•Some display utility and drivers that shipped with certain AGP and built-in display adapters may

prevent you setting the 2nd display as the main screen when display sharing

General Recommendation if you have a problem

•Check your USB port it active the device is plugged in correctly to the host system

•Unplug the USB 3.0 KVM & Data Transfer Cable and re-insert it

•Check to see that the monitor is correctly connected to your computer and it is powered ON

•Ensure to restart your computer after the driver installation

•Unplug all other USB devices from the system

•Try connecting the USB 3.0 KVM & Data Transfer Cable directly to the computer instead of

through a hub

Media Playback

•Ensure that the USB port you are using is a USB 3.0 port.

•During video playback on all platforms, do not change the display mode, position or arrangement

of video player window (such as dragging the video player window between main display and

attached display). This usually causes the video player to lag and the video may stop playing. We

suggest stopping the video playback, moving the window to the attached display and then playing

the video.

•You may experience poor video performance on some low-spec PC system.

•Some DVD playback software packages do not support playing on a second display adapter of

any kind. You may try to open the media player in the secondary display first before playing the

DVD.

•Your PC may be a lack of the correct codec to support playback of certain video format.

•Video/Media players have different decoding capability under different display modes. For better

performance it is recommended you use Windows Media Player 10 or above.

Inhaltsverzeichnis

Sprachen:

Andere Lindy Kabel und Steckverbinder Handbücher

Lindy

Lindy 42683 Bedienungsanleitung

Lindy

Lindy 42815 Bedienungsanleitung

Lindy

Lindy 43333 Bedienungsanleitung

Lindy

Lindy 42867 Bedienungsanleitung

Lindy

Lindy MST Hub 38402 Bedienungsanleitung

Lindy

Lindy 43099 Bedienungsanleitung

Lindy

Lindy 32356 Bedienungsanleitung

Lindy

Lindy 43353 Bedienungsanleitung

Lindy

Lindy 43270 1 Bedienungsanleitung

Lindy

Lindy 42923 Bedienungsanleitung

Lindy

Lindy 38240 Bedienungsanleitung

Lindy

Lindy 43098 Bedienungsanleitung

Lindy

Lindy 6104 Bedienungsanleitung

Lindy

Lindy 38409 Bedienungsanleitung

Lindy

Lindy 43375 Bedienungsanleitung

Lindy

Lindy 43250 Bedienungsanleitung

Lindy

Lindy 40930-2 Bedienungsanleitung

Lindy

Lindy 41489-93 Bedienungsanleitung

Lindy

Lindy 32569 Bedienungsanleitung

Lindy

Lindy 38158 Bedienungsanleitung

Lindy

Lindy 20975 Bedienungsanleitung

Lindy

Lindy 42701 Bedienungsanleitung

Lindy

Lindy 38235-6 Bedienungsanleitung

Lindy

Lindy 43380 Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung