Linear Technology DC1398 Bedienungsanleitung

DC1250

DESCRIPTION

Demonstration circuit 1398 is an evaluation board featur-

ing Linear Technology Corporation’s LT 9001 16-bit

Receiver Subsystem. DC1398 demonstrates good circuit

layout techniques and recommended external circuitry

for optimal system performance.

DC1398 comes with Linear Technology’s 16-bit

LT 9001 amplifier/ADC subsystem installed. The board

includes a wideband input transformer (for evaluation

with a single-ended RF signal generator) and output

C OS buffers.

DC1398 plugs into the DC890 Data Ac-

quisition demo board and the output can be easily ana-

lyzed with Linear Technology’s PScope data processing

software, which is available for no charge on our website

at http://www.linear.com.

Design files for this circuit board are available. Call

the LTC factory.

, LTC and LT are registered trademarks of Linear Technology Corporation.

QUICK START PROCEDURE

Validating the performance of the LT 9001 is simple

with DC1398, and requires only an input source, a clock

source, a computer, and a lab power supply. Refer to

Figure 1 for proper board evaluation equipment setup

and follow the procedure below:

Connect the power supply as shown in Figure 1.

There are on-board low-noise voltage regulators that

provide the three supply voltages for the LT 9001.

The entire board and all components share a com-

mon ground. The power supply should still be a low-

noise lab power supply capable of supplying at least

1 Amp.

Provide an encode clock to the ADC via S A con-

nector J3. Use a low-phase-noise clock source such

as a filtered RF signal generator or a high-quality

clock oscillator.

Obtain DC1216 for a low-phase-

noise DC clock source that can plug directly into

DC1398.

NOTE.

Similar to having a noisy input, a high-jitter (phase noise)

encode clock will degrade the signal-to-noise ratio (SNR) of the

system.

Table 1: DC1398 Connectors and Jumpers

REFERENCE FUNCTION

J1 (AIN-) Differential Board Input.

Normally not con-

nected.

See text for differential

input evalu

tion methods.

J2 (AIN+) Board Signal Input. Impedance-matched to

Ω

for use with lab signal generators.

J3 (ENC) Board Clock Input. Impedance-matched to

Ω.

Drive with a low-phase-noise clock oscil-

lator or filtered sine wave signal source.

E1 (EXT REF) Reference input to adjust the full-scale range of

the LT 9001. Connects to the SENSE pin; by

default, tied to VDD for internal reference.

E2 (VS) DC Supply input (3.8 to 6VDC).

E3 (GND) DC ground.

JP1 (PGA_GAIN) Selects the input range of LT 9001. Default is

LOW (low PGA gain, larger input range)

JP2 (RAND) Output Randomizer. Default is NOR .

JP3 (ADC_SHDN) Enables the LT 9001 ADC. Default is NOR .

JP4 (DITH) ADC Internal Dither. Default is OFF.

JP5 (A P_EN) Enables the LT 9001 amplifier. Default is EN.

Apply an input signal to the board. DC1398 allows

great flexibility in applying input signals (see the sec-

tion on Applying Input Signals). For best results, use a

low distortion, low noise signal generator with suffi-

cient filtering to avoid degrading the performance of

the amplifier and ADC.

Observe the ADC output with demo circuit DC890, a

USB cable, a Windows computer, and Linear Tech-

nology’s Pscope data processing software.

DEMO CIRCUIT 1398

QUICK START GUIDE

LTM9001 16-

bit High

fo mance ADC D ive s

LTM9001

Figure 1.

Proper Evaluation Equipment Setup

ADDITIONAL INFORMATION

Although the DC1398 demo board is ready to use on de-

livery, it has additional flexibility built in for various types

of input networks. Below is some information about con-

figuring DC1398 to meet the specific needs of your eval-

uation.

PPLYING INPUT SIGN LS

The input network consists of various components de-

signed to allow either single-ended or differential inputs,

AC-coupled or DC-coupled. Table 2 shows some possi-

ble input configurations, and which components to in-

stall. LT 9001 is designed for excellent performance

with both single-ended and differential input drive, with

little difference in distortion performance. When using

DC-coupled inputs, the inputs to DC1398 need to be lev-

el-shifted to within the input common-mode limits in the

datasheet.

Table 2: DC1398 Input Configuration Guide

CONFIGUR TION COMPONENTS NECESS RY

Single-Ended Input

AC-Coupled

(Default Setup)

No change. Transformer T1 acts as a balun for

differential drive.

Single-Ended Input

No Transformer

AC-Coupled

Remove T1, replace with 0

Ω

jumpers. ay need

to install impedance-matching resistor at R4

or R2/R6.

Single-Ended Input

No Transformer

DC-Coupled

Same as above. Change C1 and C8 to 0

Ω

jump-

ers. Inputs must be within the common-

mode voltage limits of LT 9001.

Differential Inputs Remove R7 and install R5. T1 and C1/C8 can be

replaced with 0

Ω

for DC coupling.

Signal

Generator

HP 8644B

or equiv.

Power Supply

(3.8V-6V @ 1.0A)

To DC890

BPF

NOTE.

Even a high

ality signal

synthesizer will still have noise and

harmonics that should be attenuated

with a low-pass or band-pass filter.

For good-quality high order filters,

see TTE, Lark Engineering, or

equivalent.

BPF

RF Signal Ge

erator

(HP 8644B) or other

low phase noise

clock source (e.g. DC1216)

LTM9001

NOTE.

When driving the ADC driver with a direct DC-coupled path, increased

input bias currents may occur due to the amplifier’s input impedance. See

the LT 9001 datasheet for more details.

OTHER BO RD CIRCUITRY

Device U5 is an EEPRO device that is used by the

PScope software to identify the board and apply the cor-

rect settings for the data collection.

USING PSCOPE SOFTW RE

PScope, downloadable from Linear Technology’s website

http://www.linear.com/, processes data from the DC890

FastDAACS board and displays FFT and signal analysis

information on the computer screen.

The on-board EEPRO U5 should enable automatic

board detection and auto-configuration of the software,

but if the user wishes to change the settings, they can

easily do so.

From the Configure menu in the toolbar, uncheck “Auto-

detect Device”. The default settings for DC1398 are

shown in Figure 2. The LT 9001 also has an output ran-

domizer, which the user needs to select if it is enabled on

the board. The software will automatically un-randomize

the output by performing an exclusive-OR with each bit

and the LSB.

Figure 2. Entering the correct device information for your DC. Select the correct parameters for the DC1398. Under normal conditions,

PSCOPE should automatically recognize the board and adjust the software settings accordingly.

LTM9001

Figure 3. Schematic

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Analog Devices Inc.:

DC1398A-GA

Inhaltsverzeichnis

Andere Linear Technology Hauptplatine Handbücher

Linear Technology

Linear Technology DC1238B Bedienungsanleitung

Linear Technology

Linear Technology DC1780A-A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC2026A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1763A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1257B Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology LT5557 Bedienungsanleitung

Linear Technology

Linear Technology LTC6655 Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC826C-A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC416 Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1369A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1338A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1846A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1339 Bedienungsanleitung

Linear Technology

Linear Technology DC2118A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1668A-A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1816B Bedienungsanleitung

Linear Technology

Linear Technology DC961B Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology LTC4415EMSE Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology 1315 Bedienungsanleitung

Linear Technology

Linear Technology DC1760A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1717A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC2191A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1296A Bedienungsanleitung

Linear Technology

Linear Technology DC2215A Kurzanleitung zur Einrichtung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung