Linear Technology DC150A Bedienungsanleitung

Linear Technology Corporation

DESCRIPTION

There is a demonstration board available for the

LTC1067/LTC1067-50. Demonstration board 150A

has the LTC1067 part installed and the board 150B

has the LTC1067-50 installed. The schematic for

the board is shown in Figure 15 and the assembly

drawing is shown in Figure 16. To obtain a demon-

stration board, call your local representative or Lin-

ear Technology’s marketing department. The

demonstration board has all integrated circuits,

connectors and decoupling capacitors installed.

The board is ready to be configured with the ap-

propriate resistors and jumper connections. There

are two sets of power supply connections. One is

for the LTC1067/LTC1067-50 and the other is for

the buffering op amp on the board. Having separate

connections gives the board the most flexibility. The

two sets of supplies can be connected together if a

common supply is desired. When configuring the

board for split supply operation, a jumper wire must

be installed in the JPAGND position. This connects

theAGND pin of the device to the ground plane of

the board. The JPVNEG jumper must be left open.

The power supply is then connected to V+, V –and

GND turrets (all of the GND turrets on the board

are the same). For single supply operation, insert a

wire in the JPVNEG jumper and leave the JPAGND

jumper open. This connects the V –pin to the

board’s ground plane. The JPAGND jumper must

be left open so that the on-chip resistor network

can set theAGND potential at the midpoint of the

supply. Connect the power supply to V+ and any

GND turret.

The V –turret can be left open or shorted to the

adjacent GND turret. If the buffering op amp is run

on the same single voltage supply, the VOA+ turret

and the V+ turrets must be connected together and

the VOA –turret must be shorted to the adjacent

GND turret.

The J1 BNC connector is the clock input. There is a

200W series resistor connected between the con-

nector and the CLK pin of the part. This resistor,

coupled with the CLK pin’s input capacitance, slows

down the rise and fall times of the clock signal and

decreases high frequency coupling. The clock in-

put is not terminated to 50W or 75W. An external

terminator should be used. Jumpers JP51 and

JP61 are connected in parallel with R51 and R61

respectively. Jumper JP51 connects the LPApin of

the part with the SApin. This can be used for oper-

ating modes 1 or 2.Alternatively, a 0W resistor in

the R51 position fulfills the same requirement. The

JP61

jumper connects the SA pin of the part to

the AGND pin.

This would be used for operating

Mode 3. Here, a 0W resistor in the R61 position

also works. Jumpers JP52 and JP62 perform the

same functions on the B side of the part. The buff-

ering amplifier can be configured for inverting or

noninverting operation. For inverting applications,

connect jumper JP2 positions 1 and 2.Additionally,

connect jumper JP4 for split supply applications or

JP8 for a single supply. For a noninverting applica-

tion, connect jumper JP2 positions 2 and 3.

Several other jumpers should be connected as fol-

lows:

JP1: Install a jumper wire from position 1 to position

2, leave the other positions open.

JP5: Install a jumper wire if split supply, leave open

if single supply.

JP6: Leave open.

JP7: Install a jumper wire.

JP9: Install a jumper wire if single supply, leave

open if split supply.

DC150A

LTC1067, LTC1067-50

DEMONSTRATION CIRCUIT USERS GUIDE

Linear Technology Corporation

DC150A Schematic (Also available in the datasheet)

DC150ALayout (Also available in the datasheet)

Andere Linear Technology Hauptplatine Handbücher

Linear Technology

Linear Technology DC1886A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC2194A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1367A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1662A Bedienungsanleitung

Linear Technology

Linear Technology 1172A Bedienungsanleitung

Linear Technology

Linear Technology DC861A-A Bedienungsanleitung

Linear Technology

Linear Technology DC1954A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1980A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology LTC5584 Bedienungsanleitung

Linear Technology

Linear Technology LTC2107 Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1584A Bedienungsanleitung

Linear Technology

Linear Technology DC2218A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC2117A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1668A-A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1296A Bedienungsanleitung

Linear Technology

Linear Technology DC1880A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1317A-B Bedienungsanleitung

Linear Technology

Linear Technology DC1705C Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology LTC2270 Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology LT5557 Bedienungsanleitung

Linear Technology

Linear Technology LTC6905 Series Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1759A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC2196A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC2048A Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung