Linear LTC3828EUH Bedienungsanleitung

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 802

LTC3828 DUAL 2-PHASE STEP DOWN CONVERTER WITH TRACKING

LTC3828EUH

DESCRIPTION

Demonstration circuit 802 features the dual-output,

2-phase synchronous buck regulator LTC3828EUH.

The input voltage range of the demo board is 7V to

21V. The outputs are 5V/5A

MAX

and 3.3V/5A

MAX

. De-

pending on the setting of the optional resistors and

jumpers, each output can track an external ramp

voltage during start up or one output can track an-

other output on the same board during start up. At

light load, the supplies can operate in high efficiency

mode or low output ripple mode depending on

jumper selection.

The switching frequency is a jumper-selectable

250kHz or 550kHz, or one resistor can set the fre-

quency anywhere in between. The supply can also be

synchronized by an external clock signal. A

CLOCKOUT pin provides an output clock signal to

synchronize other supplies if needed. The

LTC3828EUH regulator IC is in a small 5 mm x 5 mm

package with exposed thermal pad for low thermal

impedance.

Design files for this circuit board are available.

Call the LTC factory.

,LTC and LT are registered trademarks of Linear Technology Corporation.

Table 1.

Performance Summary (TA= 25°C)

PARAMETER CONDITION VALUE

Input Voltage 7V-21V

Output Voltage V

OUT1

= 0A to 5A 5V ± 2%

Output Voltage V

OUT2

= 0A to 5A 3.3V ± 2%

Maximum Output Current VIN = 7V-21V 5A Each Output

Switching frequency FCB = CCM Jumper selectable

250kHz or 550kHz

Full Load Efficiency V

= 12V, V

OUT1

= 5V, I

OUT1

= 5A, fsw=550kHz 93% Typical

= 12V, V

OUT2

= 3.3V, I

OUT2

= 5A, fsw=550kHz 91% Typical

QUICK START PROCEDURE

Demonstration circuit 802 is easy to set up to evalu-

ate the performance of the LTC3828EUH. Refer to

Figure 1 for proper measurement equipment setup

and follow the procedure below:

NOTE:

When measuring the input or output voltage

ripple, care must be taken to avoid a long ground lead

on the oscilloscope probe. Measure the input or out-

put voltage ripple by touching the probe tip directly

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 802

LTC3828 DUAL 2-PHASE STEP DOWN CONVERTER WITH TRACKING

across the Vin or Vout and GND terminals. See Figure 2 for proper scope probe technique.

Following table should be the default jumper settings of the DC802A demo board:

JP1

PHSMD

JP2

FSET

JP3

FCB

JP4

RUN1

JP5

RUN2

JP6

TRACK2

JP7

TRACK1

0 550kHz CCM ON ON VOUT1 EXT1

With the above default setting, the supply runs at 550kHz forced continuous current mode.

Following tables show the assembly options for the tracking circuits for VOUT1 and VOUT2:

VOUT1 TRACKING

OPTIONS TRACK2 JP6 R23 R25 C21

Softstart W/O tracking N/A DNP DNP 0.01uF

2 Track EXT1 EXT1 105K 20K DNP

3 Track VOUT2 VOUT2 105K 20K DNP

VOUT2 TRACKING

OPTIONS TRACK1 JP7 R24 R26 C22

1 Softstart W/O tracking N/A DNP DNP 0.01uF

2 Track EXT2 EXT2 95.3K 30.1K DNP

Track VOUT1 VOUT1 95.3K 30.1K DNP

*With existing tracking circuit assembly, VOUT1 starts independently (option1). VOUT2 tracks VOUT1 during start

up (option3). Figure 3 shows a typical start-up waveform with tracking.

With power off, connect the input power supply to

VIN and GND. Connect the load between VOUT1

and GND, VOUT2 and GND. Preset the load current

at 0A (minimum). Refer to Figure 1 for correct test

set up.

Turn on the input power.

NOTE:

Make sure that the input voltage does not ex-

ceed 21V.

Check for the proper output voltages. Vout1 =

4.90V-5.10V. Vout2 = 3.23V- 3.36V

NOTE:

If there is no output, temporarily disconnect

the load to make sure that the load is not set too

high.

Once the proper output voltages are established,

adjust the loads within the operating range and ob-

serve the output voltage regulation, ripple voltage,

efficiency and other parameters.

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 802

LTC3828 DUAL 2-PHASE STEP DOWN CONVERTER WITH TRACKING

Figure 1.

Proper Measurement Equipment Setup

VIN

GND

Figure 2.

Measuring Input or Output Ripple

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 802

LTC3828 DUAL 2-PHASE STEP DOWN CONVERTER WITH TRACKING

Vo1

Vo2

Figure 3.

Typical Output Voltage Tracking Waveform during Start-Up

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 802

LTC3828 DUAL 2-PHASE STEP DOWN CONVERTER WITH TRACKING

Andere Linear Controller Handbücher

Linear

Linear ANALOG DEVICES DC2448A-C Kurzanleitung zur Einrichtung

Linear

Linear ANALOG DEVICES DC2448A-A Kurzanleitung zur Einrichtung

Linear

Linear LTM8003 Kurzanleitung zur Einrichtung

Linear

Linear ANALOG DEVICES DC2448A-B Kurzanleitung zur Einrichtung

Linear

Linear LRA Bedienungsanleitung

Linear

Linear PRO Access APeX-II v2.1 Betriebsanleitung

Linear

Linear Z-Wave Series Bedienungsanleitung

Linear

Linear LTM4636 Bedienungsanleitung

Linear

Linear ANALOG DEVICES LTC7106 Kurzanleitung zur Einrichtung

Linear

Linear LTC3875 Bedienungsanleitung

Linear

Linear DC2053A Kurzanleitung zur Einrichtung

Linear

Linear DC1772A Kurzanleitung zur Einrichtung

Linear

Linear LT1943 Bedienungsanleitung

Linear

Linear DC1104A Bedienungsanleitung

Linear

Linear ANALOG DEVICES EZ-PD CCG3 Kurzanleitung zur Einrichtung

Linear

Linear ADI Power DC2654A Bedienungsanleitung

Linear

Linear ANALOG DEVICES DC2155A-A Bedienungsanleitung

Linear

Linear ANALOG DEVICES DC2448A-D Kurzanleitung zur Einrichtung

Linear

Linear ANALOG DEVICES DC1590B Kurzanleitung zur Einrichtung

Linear

Linear LTM4650 Kurzanleitung zur Einrichtung

Linear

Linear LTC3300-1 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung