Linear 747 Bedienungsanleitung

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 747

LOG-LINEAR RF/IF DETECTOR

LT5537

DESCRIPTION

Demonstration circuit 747 is a

log-linear RF/IF detector

featuring the LT

5537.

The LT5537 is a wide dynamic range RF/IF log detec-

tor, operational from below 10MHz to 1000MHz. The

lower limit of the operating frequency range can be

extended to near DC by the use of an external capaci-

tor. The input dynamic range at 200MHz with ±3dB

nonlinearity is 90dB (from –76dBm to 14dBm, single-

ended 50Ωinput). The detector output voltage slope

is normally 20mV/dB, and the typical temperature

coefficient is 0.01dB/°C at 200MHz.

Design files for this circuit board are available. Call

the LTC factory.

LTC is a trademark of Linear Technology Corporation

Table 1.

Typical Performance Summary (VCC = 3V, ENBL = 3V, TA= 25°C, unless otherwise noted. Test circuit shown in Figure 1.)

PARAMETER CONDITION VALUE

Supply Voltage 2.7V to 5.25V

Supply Current 13.5mA

Shutdown Current ENBL = Low 500µA

ENBL Voltage Low, Chip Disabled

High, Chip Enabled

0.3V max

1.0V min

ENBL Input Current V

ENBL

= 0V

ENBL

= 3V

0µA

100µA

RF/IF Input DC Common Mode Voltage (V

– 0.4) V

Small-Signal Impedance

Measured at 200MHz 1.73kΩ// 1.45pF

Output Start Voltage No Input Signal Present 0.4V

Response Time Input from –30dBm to 0dBm, C

LOAD

= 2.5pF 110ns

Baseband Modulation Bandwidth Output Load Capacitance = 2.5pF 6MHz

Input Frequency Range Operation at lower frequency is possible. See LT5537 datasheet. 10MHz to 1GHz

Maximum Input Power for

Monotonic Output

50ΩTermination

200MHz

600MHz

1GHz

14.0dBm

11.6dBm

9.4dBm

f = 10MHz

Linear Dynamic Range ±3dB Error

±1dB Error

88.8dB

72.5dB

Slope R1 = 33k (The output slope is adjustable using R1.) 19.6mV/dB

Intercept V

OUT

= 0V, extrapolated -97dBm

Sensitivity Sensitivity can be improved by as much as 10dB by using a narrow-

band input matching network. See LT5537 datasheet. -76.7dBm

Temperature Coefficient P

= -20dBm -0.007dB/°C

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 747

LOG-LINEAR RF/IF DETECTOR

f = 100MHz

Linear Dynamic Range ±3dB Error

±1dB Error

90.5dB

82.8dB

Slope R1 = 33k (The output slope is adjustable using R1.) 20.3mV/dB

Intercept V

OUT

= 0V, extrapolated -95dBm

Sensitivity Sensitivity can be improved by as much as 10dB by using a narrow-

band input matching network. See LT5537 datasheet. -77dBm

Temperature Coefficient P

= -20dBm -0.004dB/°C

f = 200MHz

Linear Dynamic Range ±3dB Error

±1dB Error

90.3dB

83.5dB

Slope R1 = 33k (The output slope is adjustable using R1.) 21.2mV/dB

Intercept V

OUT

= 0V, extrapolated -94dBm

Sensitivity Sensitivity can be improved by as much as 10dB by using a narrow-

band input matching network. See LT5537 datasheet. -76.4dBm

Temperature Coefficient P

= -20dBm 0.010dB/°C

f = 400MHz

Linear Dynamic Range ±3dB Error

±1dB Error

88.2dB

70.8dB

Slope R1 = 33k (The output slope is adjustable using R1.) 23.1mV/dB

Intercept V

OUT

= 0V, extrapolated -91dBm

Sensitivity Sensitivity can be improved by as much as 10dB by using a narrow-

band input matching network. See LT5537 datasheet. -75.3dBm

Temperature Coefficient P

= -20dBm 0.019dB/°C

f = 600MHz

Linear Dynamic Range ±3dB Error

±1dB Error

85.8dB

72.5dB

Slope R1 = 33k (The output slope is adjustable using R1.) 25.2mV/dB

Intercept V

OUT

= 0V, extrapolated -89dBm

Sensitivity Sensitivity can be improved by as much as 10dB by using a narrow-

band input matching network. See LT5537 datasheet. -74.1dBm

Temperature Coefficient P

= -20dBm 0.026dB/°C

f = 1GHz

Linear Dynamic Range ±3dB Error

±1dB Error

63.5dB

51.7dB

Slope R1 = 33k (The output slope is adjustable using R1.) 31.4mV/dB

Intercept V

OUT

= 0V, extrapolated -80dBm

Sensitivity Sensitivity can be improved by as much as 10dB by using a narrow-

band input matching network. See LT5537 datasheet. -69.2dBm

Temperature Coefficient P

= -20dBm 0.031dB/°C

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 747

LOG-LINEAR RF/IF DETECTOR

QUICK START PROCEDURE

Demonstration circuit 747 is easy to set up to evalu-

ate the performance of the LT5537. Refer to Figure 1

for proper measurement equipment setup and follow

the procedure below:

Connect voltmeter’s negative (-) lead to demo

board GND test point (E4 or E5).

Connect voltmeter’s positive (+) lead to the demo

board OUTPUT test point (E2).

Connect DC power supply’s negative (-) output to

demo board GND test point (E4 or E5).

Connect DC power supply’s positive (+) output

(2.7V to 5.25V) to demo board V

test point (E3).

NOTE:

Do not exceed 5.5V, the absolute maximum

supply voltage.

Connect signal generator’s output to demo board

INPUT port (SMA connector J1) via coaxial cable.

A 3dB attenuator may be inserted to improve input

match.

Using a jumper cable, connect demo board V

test

point (E3) to ENBL test point (E1). Now the detec-

tor is enabled (on) and is ready for measurement.

NOTE:

Make sure that the power is not applied to

ENBL before it is applied to V

. The voltages on

the ENBL test point must never exceed V

+ 0.2V.

Apply RF input signal and measure OUTPUT DC

voltages.

NOTE:

Do not exceed +22dBm, the absolute maxi-

mum RF input power.

Figure 1.

Proper Measurement Equipment Setup

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 747

LOG-LINEAR RF/IF DETECTOR

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Analog Devices Inc.:

DC747A

Inhaltsverzeichnis

Andere Linear Hauptplatine Handbücher

Linear

Linear 1524A-A Bedienungsanleitung

Linear

Linear DC2194A Kurzanleitung zur Einrichtung

Linear

Linear DC1194A Kurzanleitung zur Einrichtung

Linear

Linear DC1892A Kurzanleitung zur Einrichtung

Linear

Linear ADI Power SCP-LT3461-EVALZ Kurzanleitung zur Einrichtung

Linear

Linear ANALOG DEVICES DC2631A Kurzanleitung zur Einrichtung

Linear

Linear DC1543A Kurzanleitung zur Einrichtung

Linear

Linear LT3995 Kurzanleitung zur Einrichtung

Linear

Linear ADI Power SCP-ADP7182-EVALZ Kurzanleitung zur Einrichtung

Linear

Linear DC1630A Kurzanleitung zur Einrichtung

Linear

Linear Analog Devices DC1842B Kurzanleitung zur Einrichtung

Linear

Linear DC2007A-B Kurzanleitung zur Einrichtung

Linear

Linear DC1395A Bedienungsanleitung

Linear

Linear DC2106A-B Kurzanleitung zur Einrichtung

Linear

Linear DC951A Kurzanleitung zur Einrichtung

Linear

Linear Analog Devices LT3960 Kurzanleitung zur Einrichtung

Linear

Linear LTC3717 Bedienungsanleitung

Linear

Linear Analog Devices DC2721A-B Kurzanleitung zur Einrichtung

Linear

Linear Analog Devices ADI Power DC2685B-KIT Kurzanleitung zur Einrichtung

Linear

Linear DC1685A Kurzanleitung zur Einrichtung

Linear

Linear DC2033A Kurzanleitung zur Einrichtung

Linear

Linear ANALOG DEVICES DC2543B Kurzanleitung zur Einrichtung

Linear

Linear DC768 Bedienungsanleitung

Linear

Linear ANALOG DEVICES DC2685B Kurzanleitung zur Einrichtung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung