Linksys RE9000 Bedienungsanleitung

Manually setting up the Linksys RE9000

In situations where you want to bypass the Linksys RE9000 MU-MIMO Range Extender’s setup

wizard, you can follow the steps below to manually configure the range extender.

NOTE: This article assumes that your Linksys RE9000 is on factory defaults. To reset the Linksys

RE9000, press the Reset button for 5 seconds.

Step 1:

Turn ON the Linksys RE9000 and wait for the light indicator to blink orange.

Step 2:

Using a wireless device, locate and connect to the Linksys Extender Setup Wi-Fi.

Step 3:

Once connected, open a browser and go to http://extender.linksys.com to launch setup.

NOTE: If the Linksys RE9000 has not detected a DHCP server, it defaults to its IP address,

192.168.1.1.

Step 4:

Click the Manual Setup link at the bottom.

Step 5:

Enter “admin” in the Password field then click Login.

Step 6:

You have now bypassed the Setup wizard. Configure your manual settings as needed.

NOTE: In order to configure the upstream connection, you must use the Wizard option by going to

Wireless > Wizard.

Select your mode of choice, click Change and follow the on-screen instructions.

NOTE: If you are changing to Access Point (Wired Range Extender) mode, make sure to have an

ethernet cable ready to connect your Linksys RE9000 to your router.

Setting up the Linksys RE9000 using WPS

The Linksys RE9000 MU-MIMO Range Extender can be set up using Wi-Fi Protected Setup™

(WPS). This article will show you the steps on how to do so.

Step 1:

Plug the Linksys RE9000 into a wall outlet that is close to your router.

NOTE: Wait for the light indicator to change to orange. To learn more about this device’s light

behavior, click here.

Step 2:

Press the WPS button on your wireless router.

Step 3:

Press the WPS button at the side panel of your Linksys RE9000.

NOTE: The indicator light on the front of the range extender will blink green.

Step 4:

Wait for the front light to turn solid green to indicate that the connection is successful.

Accessing the Linksys RE9000’s web-based setup page

The Linksys RE9000 MU-MIMO Range Extender is a tri-band ethernet bridge and a range

extender all-in-one. This article will show you how you can access the Linksys RE9000’s web-based

setup page.

Step 1:

Connect a device to your range extender’s Wi-Fi and launch a browser once connected.

Step 2:

Do one of the following methods to log in to the Linksys RE9000’s web-based setup page:

Enter "http://extender.linksys.com” in the Address bar.

Enter “http://RE9000” (for Windows® users) in the Address bar

NOTE: If you changed your Linksys RE9000’s name, then you will need to use the custom name

(e.g., http://MyAP).

Enter "http://RE9000.local" (for Mac® users) in the Address bar.

NOTE: If you changed your Linksys RE9000 name, then you will need to use the custom name

(e.g., http://MyAP.local).

Enter the Linksys RE9000’s IP address.

NOTE: If the Linksys RE9000 does not detect a DHCP server, the default IP address

is 192.168.1.1. Otherwise, you will need to look up your range extender’s IP address in the DHCP

table. To know how to do this using a Linksys Wi-Fi Router, click here. If you are using a Linksys

Smart Wi-Fi Router, click here.

QUICK TIP: Some options may not be available in Access Point mode due to the design and

functionality as an access point.

Step 3:

You will be prompted for an administrative Password. If you have changed your password, enter

your customized password. Otherwise, enter the default “admin” in the field then click Login.

ADVANCED CONFIGURATION

1. What is 802.11r?

802.11r is a proprietary implementation of IEEE 802.11r-2008 (fast BSS transition) on Linksys

RE9000 to support Seamless Roaming. When an 802.11r-compliant device such as iPhone® roams

from one Linksys RE9000 to another Linksys RE9000 or any Linksys Max-Stream product, the fast

transition mechanism can reduce the authentication time needed for a full WPA/WPA2 Personal

four-way handshake to under 100 ms.

2. When would I need to enable the 802.11r feature on my Linksys RE9000?

If you have any Linksys Max-Stream wireless product in your network, enable this feature to support

Fast BSS Transition for roaming from one Linksys RE9000 to another Linksys RE9000.

3. Does the Linksys RE9000 support Seamless Roaming?

Yes. Seamless Roaming allows your supported device such as an iPad® or iPhone® to roam

between a supported Linksys Max-Stream router or range extender products (make sure that the

latest firmware is installed with Seamless Roaming support).

Moving between a traditional router and range extender, your home Wi-Fi signal can experience lag

or a dropped connection. With its intuitive technology, Seamless Roaming allows you to move from

one room to another and automatically switches your device to connect to the strongest Wi-Fi signal.

4. What are the guidelines when using Seamless Roaming on my Linksys RE9000?

In order for Seamless Roaming to work properly, you must configure the range extender accordingly:

Works with another Linksys Max-Stream extender or router

NOTE: You may need a firmware update to add the Seamless Roaming support. Check your

product's Release Notes to be sure.

Wi-Fi names must be the same

Must be on the same subnet

Must have the same Wi-Fi security settings

NOTE: Only WPA2 or WPA2/WPA Mixed Mode is supported.

The client device must also support Seamless Roaming (ex., on Android™ devices, the

option is called Wi-Fi Roaming). Check your device's manufacturer to make sure that this

option is enabled. Seamless Roaming works between Wi-Fi to Wi-Fi only and not 4G to Wi-

Fi when using a mobile device.

5. Does my Linksys RE9000 support MAC Filtering?

Yes. If you set up Mac Filtering on your Linksys RE9000 you must also setup Mac Filtering on your

existing wireless router. Otherwise you are only allowing or preventing clients to connect to the

Linksys RE9000 but you still need to configure Mac Filtering on any other Wireless router, Access

Point or Extender that you have in your network to allow or prevent clients.

6. How do I configure Access Control feature of my Linksys RE9000?

To enable the Access Control feature of the Linksys RE9000, follow the steps below:

Step 1:

Access the Linksys RE9000’s web-based setup page. For instructions, click here.

Step 2:

Go to Wireless.

Step 3:

Go to Access Control and select the Enabled radio button.

Step 4:

Configure the settings as needed.

Access Mode:

Allow - Only devices on the Access Control List will have access to the Wi-Fi.

Deny - Devices on the Access Control List will not have access to the Wi-Fi.

Add a Device:

To allow or prevent a wireless device to connect to the range extender, you can either select a

Wireless Client or enter a MAC address.

Wireless Client - Displays computers and other devices currently on the Wi-

Fi. Select a client from the drop-down list and click Save.

MAC Address - Manually enter a MAC address and click Save.

NOTE: After selecting a Wireless Client or entering a MAC address, make sure to click Save next to

the field before clicking the Save button.

Access Control List:

Displays all the MAC Addresses that you have added.

Click Edit to edit the MAC address of the client. The edited MAC Address will

show in the MAC Address field. If you want to remove a MAC Address item

from the list, click Remove.

Step 5:

Click Save once done.

7. Where can I find the Band Steering option in the Linksys RE9000’s web-based setup page?

To locate the Band Steering option in the Linksys RE9000’s web-based setup page, follow the steps

below:

Step 1:

Access the Linksys RE9000’s web-based setup page. For instructions, click here.

Step 2:

Go to Wireless > Basic Settings.

Step 3:

The Band Steering check box is found under Extended Wireless Settings section.

NOTE: Leaving Band Steering ON is the recommended setting.

TROUBLESHOOTING

1. My Wi-Fi is not being detected during Setup, what could be the problem?

The Linksys RE9000 uses the 5 GHz band as the dedicated backhaul connection. You must have a

Dual-Band network with the 5 GHz working in order for the Linksys RE9000 to connect to your

upstream connection.

2. Can I use the Linksys RE9000 if I only have a 2.4 GHz network?

Yes. During Setup, you can use the Access Point mode option. It will require the Linksys RE9000

to be connected to your network with an ethernet cable.

3. Why can’t I find the Linksys Extender Setup in my Wi-Fi list?

Make sure the light on the Linksys RE9000’s front panel is blinking orange. If you still can’t see the

setup network, move the Wi-Fi device being used to set up closer to the Linksys RE9000. Wait for

the blinking orange light and refresh the list.

4. I correctly entered my Wi-Fi password during the setup. Why does the Enter your

password page still show an error?

The Linksys RE9000 is likely at the outside limit of the router’s signal. The signal could be being

interrupted before it reaches your router. Move your Linksys RE9000 closer to your router.

5. Why am I experiencing poor signal or slow speed on my Linksys RE9000?

Be sure to place your Linksys RE9000 in an ideal location, as indicated by the Spot Finder

technology (In Range Extender mode).

NOTE: When you move around your home, your wireless devices may not disconnect from the

router until they lose Wi-Fi signal. This may occur even if the Wi-Fi signal from the Linksys RE9000

is stronger (and vice versa). If you are having connection issues, select the Wi-Fi with stronger

signal.

6. Does the Linksys RE9000 support DFS Channels?

No, the Linksys RE9000 does not support DFS Channels.

My Linksys RE9000 is not detecting my Wi-Fi during setup

Scenario: My Linksys RE9000 is not detecting my Wi-Fi during setup.

The Linksys RE9000 MU-MIMO Range Extender uses a dedicated 5 GHz band as the backhaul

(uplink) connection to a Dual-Band router. If your Linksys RE9000 is unable to see the 5 GHz

network, here are things you can check (in the following order):

You must have a dual-band router

Make sure that the 5 GHz band on your wireless router is enabled, working and

broadcasting.

If the extender is too far away, try to move the extender closer for setup. After setup, you

can move it to another location.

The Linksys RE9000 does NOT support Dynamic Frequency Selection (DFS) channels. If

your router supports DFS channels, it is possible that your router is using a DFS channel;

therefore, the extender will not detect the 5 GHz band.

NOTE: DFS channels are 52-64 and 100-140. You can contact support for the wireless router to

confirm if the router supports DFS channels and if it is using one of the DFS channels. If it does,

they need to change the router’s 5 GHz channel to a non-DFS channel and then run the setup again

on the Linksys RE9000.

Setting up the Linksys RE9000 to Range Extender mode

The Linksys RE9000 MU-MIMO Range Extender can be set up in two ways, through Range

Extender mode or Access Point mode. This article will show you the steps on how you can set it up

on Range Extender mode.

Before you begin, make sure to have the following:

An existing Dual-Band wireless router or access point (5 GHz band is used as the dedicated

backhaul connection)

A computer or tablet with Wi-Fi capability

Your existing Wi-Fi name and password

Step 1:

Turn ON the Linksys RE9000 and wait for the light indicator to blink orange.

Step 2:

Using a wireless device, locate and connect to the Linksys Extender Setup Wi-Fi.

Step 3:

Once it is connected, open a browser and go to http://extender.linksys.com to launch setup. Then

click on Start Setup.

NOTE: If the Linksys RE9000 has not detected a DHCP server, it defaults to its IP address,

192.168.1.1.

QUICK TIP: If you want to bypass the setup wizard, click on Manual Setup.

Step 4:

Select the As a wireless range extender option and click Next.

Step 5:

Connect to your existing 5 GHz Wi-Fi.

NOTE: Setup will scan for 5 GHz networks only. A dual-band network is required since it uses

the 5 GHz radio as the upstream connection to your existing dual-band Wi-Fi. If you do not have a

Dual-Band Wi-Fi, you can use the Access Point option.

Andere Handbücher für RE9000

Inhaltsverzeichnis

Andere Linksys Extender Handbücher

Linksys

Linksys N300 Bedienungsanleitung

Linksys

Linksys RE6800 Bedienungsanleitung

Linksys

Linksys WRE54G - Wireless-G Range Expander Repeater Original Betriebsanleitung

Linksys

Linksys RE9000 Handbuch

Linksys

Linksys WRE54G-RM - Refurb Wireless-G Range Expander Bedienungsanleitung

Linksys

Linksys RE6500 Bedienungsanleitung

Linksys

Linksys RE6350 Bedienungs- und Sicherheitshinweise

Linksys

Linksys RE6700 Bedienungsanleitung

Linksys

Linksys AC3000 Bedienungsanleitung

Linksys

Linksys WRE54G - Wireless-G Range Expander Repeater Original Betriebsanleitung

Linksys

Linksys WRE54G - Wireless-G Range Expander Repeater Bedienungsanleitung

Linksys

Linksys RE6300 Bedienungsanleitung

Linksys

Linksys WRE54G - Wireless-G Range Expander Repeater Bedienungsanleitung

Linksys

Linksys DMA2200 - Media Center Extender Bedienungsanleitung

Linksys

Linksys RE1000 Bedienungsanleitung

Linksys

Linksys RE6700 Bedienungsanleitung

Linksys

Linksys WSB24 Original Betriebsanleitung

Linksys

Linksys FlipShare TV CTV1W Bedienungsanleitung

Linksys

Linksys RE6500 Bedienungsanleitung

Linksys

Linksys PLW400 Bedienungsanleitung

Linksys

Linksys RE6300 Bedienungsanleitung

Linksys

Linksys AC 1200 Max Bedienungsanleitung

Linksys

Linksys WMCE54AG - Wireless A/G Media Center... Bedienungsanleitung

Linksys

Linksys RE1000 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung