Lipper Oblo 1.0 Bedienungsanleitung
Oblo 1.0 Aluminum Blinds
OEM INSTALLATION MANUAL
Rev: 09.08.22 Page 2 CCD-0006415
TABLE OF CONTENTS
Introduction 2
Safety 2
Resources Required 3
Installation 3
Operation 4
Notes 5
Introduction
This document outlines the procedure to install and operate Oblo 1.0 aluminum blinds.
NOTE: Images used in this document are for reference only when assembling, installing and/or operating
this product. Actual appearance of provided and/or purchased parts and assemblies may differ.
Additional information about this product can be obtained from lippert.com/support or by downloading
the free LippertNOW app. The app is available on Apple App Store® for iPhone® and iPad® and also on
Google Play™ for Android™ users. Apple App Store®, iPhone®, and iPad® are registered trademarks of Apple
Inc. Google Play™ and Android™ are trademarks of Google Inc.
For information on the assembly or individual components of this product, please visit:
https://support.lci1.com/window-accessories
The "WARNING" symbol above is a sign that a procedure has a safety risk involved and may cause
death or serious personal injury if not performed safely and within the parameters set forth in this
manual.
The “CAUTION” symbol above is a sign that a safety risk is involved and may cause personal injury
and/or product or property damage if not safely adhered to and within the parameters set forth
in this manual.
Safety
Read and understand all instructions before installing or operating this product. Adhere to all safety labels.
This manual provides general instructions. Many variables can change the circumstances of the instructions,
i.e., the degree of difficulty, operation and ability of the individual performing the instructions. This
manual cannot begin to plot out instructions for every possibility, but provides the general instructions,
as necessary, for effectively interfacing with the device, product or system. Failure to correctly follow the
provided instructions may result in death, serious personal injury, severe product and/or property damage,
including voiding of the Lippert limited warranty.
Rev: 09.08.22 Page 3 CCD-0006415
• (6) #10 x 1/2" (3,5 x 13mm) screws
• Appropriate drive bits
• Cordless or electric drill or screw gun
• 1-2 people depending on task
Installation
1. Center the Oblo aluminum blind over the window (Fig. 1).
NOTE: Oblo aluminum blinds have custom sizing. Blind sizes and images used in this document are for
reference only when assembling, installing and/or operating this product.
2. Verify that the blind is spaced evenly around the window by measuring at the top (Fig. 1A), bottom
(Fig. 1B), left side (Fig. 1C), and right side (Fig. 1D) between the window frame and the blind.
Measurements A and B should be equal and measurements C and D should be equal.
Fig. 1
Caps
Inside blind
Window edge
Wall
Fig. 2
3. Fasten the blind to the wall using the (6) #10 x 1/2" (3,5 x 13mm) screws.
NOTE: Be careful not to damage the internal cable when installing the mounting screws (Fig. 2).
4. Once secured, place the caps in the holes one by one.
Internal cable
A
D
C
B
Resources Required
Fastener holes (3)
Fastener holes (3)
Rev: 09.08.22 Page 4 CCD-0006415
Operation
Oblo Blinds have three different features: blind (Fig. 3A), screen (Fig. 3B) and latch (Fig. 3C).
1. Grip the middle of the lower profile near the latch to raise the Oblo screen slowly and latch to the Oblo
blind at the top (Fig. 4A).
2. Grip the top screen and slowly pull down (Fig. 5A). Both screen and blind can be used at the same time.
3. When blind is completely down, unlatch from screen and raise to desired position (Fig. 6).
NOTE: Do NOT rapidly raise and lower the assembly profiles. Rapidly raising and lowering the assembly
profiles may cause damage to the Oblo Blinds or wall of the unit.
Screen completely up
Blind and screen in use
A
B
C
Blind completely down
A
Fig. 3 Fig. 4
Fig. 5
A
Fig. 6
Rev: 09.08.22 Page 5 CCD-0006415
Notes
The contents of this manual are proprietary and copyright protected by Lippert. Lippert prohibits the copying or
dissemination of portions of this manual unless prior written consent from an authorized Lippert representative
has been provided. Any unauthorized use shall void any applicable warranty. The information contained in this
manual is subject to change without notice and at the sole discretion of Lippert. Revised editions are available
for free download from lippert.com.
Please recycle all obsolete materials.
For all concerns or questions, please contact
Lippert
Inhaltsverzeichnis
Andere Lipper Jalousie Handbücher
