Lippert Components OneControl Unity Board M Series Bedienungsanleitung

OneControl®

Unity Board™M Series

Rev. Q (Thor)

OWNER'S MANUAL

Rev: 03.06.19 Page 2 CCD-0001540

TABLE OF CONTENTS

Introduction 2

Safety 2

Operation 3

Awning 3

Bed Lifts 3

Fans 4

Generator 4

HVAC (Heating, Ventilation, Air Conditioning) 5

Lighting 7

Monitor Panel 7

Slides 7

Stabilizers 7

Bluetooth Connection 8

Lockout 9

Troubleshooting 9

Introduction

The OneControl® Touch Panel is a touchscreen device that accesses system controls and monitoring

software for recreational vehicles. The OneControl Unity Board™ is an electronic control system that

provides direct power, control, monitoring and diagnostics for coach functions, including awnings,

lighting, fans, HVAC, generators, water tanks, water pumps, tank heaters and battery levels. Each slide-out is

controlled by its own module that is linked to the system via CAN network. Powering up the coach will also

turn on the OneControl Touch Panel and the various controllers throughout the coach.

Additional information about this product can be obtained from lci1.com/support or by downloading

the free myLCI app. The app is available on iTunes® for iPhone® and iPad® and also on Google Play™ for

Android™ users.

iTunes®, iPhone®, and iPad® are registered trademarks of Apple Inc. Google Play™ and Android™ are

trademarks of Google Inc.

Safety

Read and understand all instructions and safety labels outlined in this manual before operating the system.

Contact LCI Customer Service if there are questions or concerns about the procedures in the manual.

The “WARNING” symbol above is a sign that an installation procedure has a safety risk involved and

may cause death, serious personal injury or severe product or property damage if not performed

safely and within the parameters set forth in this manual.

Moving parts can pinch, crush or cut. Keep clear and use caution.

Rev: 03.06.19 Page 3 CCD-0001540

Operation

The OneControl Touch Panel will be launched upon startup of the coach. The home screen will appear on

startup (Fig. 1) with icons representing systems controlled by the Unity Board.

The device can be powered on or off using the power button (Fig. 1A) on the front of the touch panel.

NOTE: Stabilizers are optional equipment on some models/floor plans. The Stabilizers icon will only

populate if that feature is available.

To operate a system, press the icon representing that system. After accessing and adjusting a system via a

touchscreen icon, push the Home icon in the center of the bottom row of the touchscreen to return to the

OneControl home screen.

Fig. 2

Fig. 1

Awning

1. Press the Awning icon.

2. Press the EXTEND (+) button (Fig. 2A)

to extend the awning and press the

RETRACT (-) button (Fig. 2B) to retract the

awning.

Bed Lifts

1. Press the Bed Lifts icon to access the Bed

Lift screen.

2. Press RAISE (Fig. 3A) to raise the bed and

press LOWER (Fig. 3B) to lower the bed.

Fig. 3

Rev: 03.06.19 Page 4 CCD-0001540

Fans

1. Press the Fan icon to access the

Fan screen.

2. Select a fan and then press the

button to turn on the fan (Fig. 4).

Press again to turn the fan off.

Generator

1. Press the Generator icon to access the Generator screen (Fig. 5).

2. Press the SETTINGS button (Fig. 5A).

3. Adjust the generator according to user preference (Fig. 6).

4. Press the START/STOP icon (Fig. 5B) on the right side of the screen to run or stop the generator.

Fig. 6

Fig. 4

Fig. 5

Rev: 03.06.19 Page 5 CCD-0001540

HVAC (Heating, Ventilation, Air Conditioning)

1. Press the HVAC icon.

2. Press the Climate zone displayed (Fig. 7).

3. There are two boxes on the left side of the screen (Fig. 8). The top box (Fig. 8A) controls the heating/

cooling mode. The bottom box (Fig. 8B) controls the fan. Press the top box to choose the HVAC mode.

A large box will populate with available options for that climate zone (Fig. 8).

A. Heat/Cool: This mode provides High and Low set points. The HVAC system will operate to keep the

temperature between these two set points. Refer to step 5C.

B. Heat (Fig. 8C): This mode has a single set point and the furnace or heat pump will operate to keep

the temperature at that set point.

NOTE: If equipped with a heat pump, users will be prompted to choose a heat source (Fig. 8D). The options

are Gas or Heat Pump.

C. Cool (Fig. 9A): This mode has a single set point and the air conditioning will operate to maintain

the temperature at this point.

D. Off (Fig. 9B): Tapping this button turns off the HVAC system.

E. Once the desired mode is selected, press the CLOSE button (Fig. 9C) on the right.

4. Press the bottom of the two boxes on the left (Fig. 8B) to choose the Fan mode. A large box will

populate with available fan settings (Fig. 10).

A. High (Fig. 10A): The fan will run continuously on high until another setting is chosen.

B. Low (Fig. 10B): The fan will run continuously on low until another setting is chosen.

C. Auto (Fig. 10C): The fan will run when the HVAC system calls for heating or cooling, then shuts off

after the set point is reached.

NOTE: The fan will continue to run for two minutes after the set point has been reached in order to cool the

compressor or furnace.

D. Once the desired fan setting has been selected, press the CLOSE button (Fig. 10D) on the right.

Fig. 7 Fig. 8

Fig. 9 Fig. 10

Rev: 03.06.19 Page 6 CCD-0001540

Counterclockwise

Clockwise

Cool Heat

5. Adjust the set points for the climate zone by updating the display.

NOTE: The adjusted temperature for the climate zone will be displayed inside a radius with a white dot on

it (Figs. 11 and 12).

A. Press and hold the white dot, then drag it around the radius (Figs. 11 and 12) to set the climate

zone's temperature set point.

I. Dragging the dot counterclockwise will lower (cooler) (Fig. 11) the set temperature.

II. Dragging the dot clockwise around the radius will raise (hotter) (Fig. 12) the set temperature.

B. Once the desired set point is reached, release pressure on the white dot.

C. Two white dots will appear (Fig. 13) when in Heat/Cool mode (Fig. 13A).

I. Set the low end (cool) of the temperature range by moving the left dot counterclockwise.

II. Set the high end (heat) of the temperature range by moving the right dot clockwise.

Fig. 11 Fig. 12

Fig.13

Rev: 03.06.19 Page 7 CCD-0001540

Lighting

1. Press the Lighting icon to access the

Lighting screen (Fig. 14).

NOTE: Individual light status is displayed by

a light bulb to the left of the light's

name (Fig. 14A). The light icon will

display a lit bulb if the light is on or a

dim bulb if the light is off.

2. Pressing the individual light buttons will

turn that light on or off.

3. Pressing the highlighted ALL ON or ALL

OFF icons (Fig. 14B) will turn all lights on

or off.

Monitor Panel

1. Press the Monitor Panel icon to access the

Tank Monitor screen (Fig. 15).

2. The monitored systems (Fig. 15A) will

display the status of the various tanks.

3. Press the buttons on the right to turn on

or off a specific component (Fig. 15B).

NOTE: The icons will light up when the

corresponding device is in use.

Slides

1. Press the Slides icon to access the Slides

screen (Fig. 16).

2. Select a slide-out to operate.

A. Press the OUT (+) button (Fig. 16A) to

extend the slide-out.

B. Press the IN (-) button (Fig. 16B) to

retract the slide-out.

Stabilizers

1. Press the Stabilizers icon to access the

Stabilizers screen (Fig. 17).

2. Select a stabilizer to operate.

A. Press EXTEND (Fig. 17A) to extend the

stabilizer.

B. Press RETRACT (Fig. 17B) to retract the

stabilizer.

Fig. 16

Fig. 14

Fig. 15

Fig. 17

Rev: 03.06.19 Page 8 CCD-0001540

Fig. 18 Fig. 19

Fig. 20 Fig. 21

Fig. 22 Fig. 23

Bluetooth Connection

After installing the LCI OneControl app from the Apple app store or the Google Play store, open OneControl

to start the procedure to connect a smart device to Bluetooth.

NOTE: The minimum requirements for the smart device are IOS 9.0 or Android 5.0 with Bluetooth 4.0.

1. Tap the I ACCEPT button (Fig. 18A) on the End User License Agreement (EULA) view.

2. Tap the GET STARTED button (Fig. 19A) on the Welcome screen.

3. Select BLUETOOTH (Fig. 20A) when prompted.

4. Find the system name (Fig. 21A) that matches the ID supplied on the OneControl Bluetooth system.

5. Enter the password (Fig. 22A) included on the OneControl wireless system.

6. Type in a PIN number (Fig. 23) to prevent unintended access to the coach.

7. After OneControl has successfully connected, tap the CONTINUE button to finish the setup.

Rev: 03.06.19 Page 9 CCD-0001540

What Is Happening? Why? What Should Be Done?

Missing icons

Power disconnected Verify adequate 12V power and ground to the

appropriate module.

Loose CAN harness

connections

Verify the CAN data harnesses are connected. Remove the

data harnesses and re-seat them. Make sure connector pins

are not loose.

Missing slide icon Bad or disconnected

controller

Verify all slide controllers are connected and functional. Replace

bad controller.

Selected function

does not operate

Function is

locked out

If the icon is present, but will not operate on the touchscreen, it

may be locked out because the ignition is on. Turn ignition off.

Function already

open

If icon is present, but grayed out, the function could be open

on a smart device connected to the OneControl app. Close

function on smart device.

Wrong fuse setting In the configurator, verify the fuse has been set to the

appropriate setting for that function.

On/Off feature turns

on, but immediately

turns off

Wrong fuse value In the configurator, make sure the proper fuse value has been

set for that output.

Touch panel will not

power up

No fuse Make sure the 5A fuse in the power center is present and intact.

Loose fuse Re-seat loose fuse.

Blown fuse Replace fuse.

Heat pump will

not operate and

switches to gas heat

Defaults to gas heat

because certain

conditions are not

met

The outside temperature must be above 47 degrees.

The set point cannot be more than 8 degrees above the current

zone temperature; e.g., climate zone temperature is 68 degrees,

then the set point cannot exceed 76 degrees.

Fig. 24

Lockout

There may be lockout capability from a motorized ignition if the brake system is wired into the controller.

If a signal is received, the Unity Board will lock out several functions to prevent operation of the devices

during transit.

If this occurs, there will be a padlock displayed at the top right-hand corner of the home screen (Fig. 24A),

and a padlock will also be shown to the right of the functions that are locked (Fig. 25A).

Troubleshooting

Fig. 25

The contents of this manual are proprietary and copyright protected by Lippert Components, Inc. (“LCI”).

LCI prohibits the copying or dissemination of portions of this manual unless prior written consent from an

authorized LCI representative has been provided. Any unauthorized use shall void any applicable warranty.

The information contained in this manual is subject to change without notice and at the sole discretion of LCI.

Revised editions are available for free download from lci1.com.

Please recycle all obsolete materials.

For all concerns or questions, please contact

Lippert Components, Inc.

Ph: (574) 537-8900 | Web: lci1.com | Email: [email protected]

Inhaltsverzeichnis

Andere Lippert Components Fernbedienung Handbücher

Lippert Components

Lippert Components 260782 Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung