Lippert Furrion Chill FACR13SA Series Bedienungsanleitung

ROOFTOP AIR CONDITIONER WITH ELEC-

TRONIC CONTROL

CLIMATISATION DE TOIT AVEC COMMANDE

ÉLECTRONIQUE

AIRE ACONDICIONADO PARA TECHO CON

CONTROL ELECTRÓNICO

MODEL/MODÈLE/MODELO: FACRSA**, FACRSA**, FACRSA**

FACRSA**AM, FACRSA**AM, FACRSA**AM, FACTCA**

FACTCA**OEM

USER MANUAL/MANUEL DE L’UTILISATEUR/ MANUAL DE USUARIO

* Picture shown here is for reference only.

* L’image présentée ici n’est qu’une référence

* La imagen que se muestra es solo como referencia.

** Product Color/** Couleur du produit/**Colordelproducto CCD-0005730 Rev: 04-25-22

English

CCD-0005730 Rev: 04-25-22 - 1 -

Furrion Model No. Lippert No.

FACR13HESA-PS 2021132276

FACR13HESA-BL 2021130013

FACR13HESA-PS-AM 2021132277

FACR13HESA-BL-AM 2021132275

FACR14SA-PS 2021123613

FACR14SA-BL 2021123563

FACR14SA-PS-AM 2021123705

FACR14SA-BL-AM 2021123707

FACR15SA-PS 2021123799

Furrion Model No. Lippert No.

FACR15SA-BL 2021123630

FACR15SA-PS-AM 2021123793

FACR15SA-BL-AM 2021123708

FACR15HESA-PS 2021130009

FACR15HESA-BL 2021130010

FACR15HESA-PS-AM 2021130011

FACR15HESA-BL-AM 2021130008

FACT12CA-PS 2021123541

FACT12CA-PS-OEM 2022007391

Thank you for purchasing this Furrion® product. Before operating your new appliance, please read these instructions carefully. This

instruction manual contains information for safe use, installation and maintenance of the appliance.

Please keep this instruction manual in a safe place for future reference. This will ensure safe use and reduce the risk of injury. Be

sure to pass on this manual to new owners of this appliance.

The manufacturer does not accept responsibility for any damages due to disregarding these instructions.

CONTENTS

EXPLANATION OF SYMBOLS.........................................................................................................................................................................

IMPORTANT SAFETY INSTRUCTIONS.......................................................................................................................................................

Handling the device.....................................................................................................................................................................................................................................2

Handling Electrical Cables......................................................................................................................................................................................................................3

BEFORE INSTALLING ........................................................................................................................................................................................

What’s in the Box...........................................................................................................................................................................................................................................3

Choosing Proper Location for the Air Conditioner....................................................................................................................................................................3

Roof Preparation...........................................................................................................................................................................................................................................4

Air Distribution Duct Sizing and Design...........................................................................................................................................................................................5

Air Distribution System Installation.....................................................................................................................................................................................................5

Preparing Wire Connections..................................................................................................................................................................................................................5

INSTALLATION......................................................................................................................................................................................................

Installing the Rooftop Unit........................................................................................................................................................................................................................6

Installing the Wall Thermostat ...............................................................................................................................................................................................................6

Installing the Air Distribution Box.........................................................................................................................................................................................................6

DIP Switch Settings.....................................................................................................................................................................................................................................8

Wire Connection - Digital Furrion Wall Controller/Thermostat...........................................................................................................................................9

Final Installation.............................................................................................................................................................................................................................................10

OPERATION ...........................................................................................................................................................................................................

Ducted Systems............................................................................................................................................................................................................................................11

Non-Ducted System ...................................................................................................................................................................................................................................11

Thermostat Use.............................................................................................................................................................................................................................................11

CLEANING AND MAINTENANCE ..................................................................................................................................................................

TROUBLESHOOTING ........................................................................................................................................................................................

SPECIFICATIONS.................................................................................................................................................................................................

WIRING DIAGRAM................................................................................................................................................................................................

EXPLANATION OF SYMBOLS

This manual has safety information and instructions to help you

eliminate or reduce the risk of accidents and injuries. Always

respect all safety warnings identified with these symbols. A

signal word will identify safety messages and property damage

messages, and will indicate the degree or level of hazard

seriousness.

DANGER

Indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

WARNING

Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate personal injury, or

property damage.

IMPORTANT SAFETY INSTRUCTIONS

This manual has safety information and instructions to help

users eliminate or reduce the risk of accidents and injuries.

Please read this instruction manual carefully before installation

and start-up, and store it in a safe place for future reference.

If you pass on the device to another person, hand over this

instruction manual along with it.

The manufacturer accepts no liability for damage in the

following cases:

●Faulty assembly or connection

●Damage to the product resulting from mechanical

influences and excess voltage

●Alterations to the product without express permission from

the manufacturer

●Use for purposes other than those described in the

operating manual.

The following basic safety information should be heeded when

using electrical devices to protect against:

●Electric shock

●Fire hazards

●Injury

All Furrion product referenced in this manual is to be installed in

accordance with local and national codes, including the latest

editions of the following standards:

USA:

–NFPA 1192

–NFPA 70

Canada:

●C22.1

●CSA Z240

Handling the device

WARNING

●Installation and repair of the rooftop air conditioner

must only be carried out by qualified personnel who

are familiar with the risks involved and the relevant

regulations. Inadequate repairs may cause serious

hazards.

●Electrical devices are not toys. Keep electrical devices

out of reach of children or elderly persons. Do not allow

them to use electrical devices without supervision.

●Prevent inexperienced people from using the device

without supervision.

●Do not undo the upper cover of the rooftop air

conditioner in the event of a fire. Use approved

extinguishing agents instead. Do not use water to

extinguish fires.

CAUTION

●The rooftop air conditioner must be installed securely so

that it cannot fall down.

●Only operate the rooftop air conditioner if you are certain

that the housing and the cables are not damaged.

●Do not use the rooftop air conditioner near flammable

fluids or in closed rooms.

●Make sure no combustible objects are stored or installed

near the air outlet. A distance of at least 20” must be

kept.

●Do not reach into air outlets or insert any foreign objects

into the device.

●Only use the device as intended.

●Do not make any alterations or conversions to the device.

●If faults occur in the refrigerant circuit, the system must

be checked by a certified service technician and repaired

properly. The refrigerant must never be released into the

air.

English

CCD-0005730 Rev: 04-25-22

- 2 -

Handling Electrical Cables

WARNING

The electrical power supply must only be connected by a

qualified electrician.

CAUTION

●Refer to NEC (National Electric Code) for proper sizing of

wire gauge (awg) based on cable length and overcurrent

protection rating that is suppling power to the air

conditioner.

●See rooftop unit nameplate for proper overcurrent

protection sizing.

●Attach and lay the cables so that they cannot be tripped

over or damaged.

●Only a qualified electrician should connect the rooftop air

conditioner to electrical power.

●Do not lay loose or bent cables next to electrically

conductive materials.

●Do not pull on the cables.

●Use cable ducts to lay cables through walls with sharp

edges.

●Refer to rooftop unit nameplate and NEC for proper power

supply rating.

BEFORE INSTALLING

Read this installation manual completely before installing the

rooftop air conditioner.

The following tips and instructions must be observed while

installing the rooftop air conditioner.

What’s in the Box

Open and remove the components from carton. Make sure you

have all the following items included in the packaging, if any

item is missing, contact your dealer.

Rooftop Air Conditioner (sold separately):

Rooftop Unit

Mounting

Frame

Filter

ADB Shroud

Control Box

Bolt

Control Knob

Lower Duct Divider

Upper Duct Divider

PE Foam

●Rooftop Unit x 1

●Warranty Manual x 1

Air Distributor Box:

Rooftop Unit

Lower Duct Divider

with Plactic Screws

Upper Duct

Divider

Mounting Frame

Filter

Screw Cap

ADB Shroud

Control Box

Bolt

PE Foam

User Manual &

Warranty Manual

Self-tapping

screw

Warning Card

User Manual

●Upper Duct Divider x 1

●Lower Duct Divider x 1

●Bolt x 4

●Mounting Frame x 1

●Control Box (sold separately) x 1

●Air Distribution Box (ADB) Shroud x 1

●Filter x 1

●PE Foam x 1

●Self-tapping Screws x 6

●Screw Cap x2

●Instruction Manual x 1

●Warranty Manual x 1

Choosing Proper Location for the Air

Conditioner

IMPORTANT: The roof must be designed to support the

weight of the rooftop unit and the weight of 2 installers

standing on the roof.

There are two ways of installing the rooftop air conditioner:

1. Using the existing roof vent opening in the vehicle roof.

2. Making a new opening. In this case the opening should be

reinforced by an appropriate frame as required.

Existing Roof Vent Opening

The air conditioner is designed to fit over an existing 14” roof

vent opening.

New Opening

When no roof vent is available or another location is desired,

the following is recommended:

–For one unit installation - the air conditioner should be

mounted slightly forward of center (front to back) and

centered from side to side.

–For two unit installations, install one air conditioner one

third from the front of the RV and the other air conditioner

two thirds from the front of the RV, aligned in the center.

It is preferred that the air conditioner be installed on a relatively

flat and horizontal roof section measured when the RV is

parked on a level surface.

NOTE: A 15° slant to either side or front to back is acceptable

for all units. If the roof exceeds 15° please use an exterior

leveling shim to make air conditioner level.

English

CCD-0005730 Rev: 04-25-22 - 3 -

After the Location Has Been Selected:

1. Check for obstructions in the area where the air

conditioner will be installed.

Center Line

of Rooftop

Front

Roof Opening

18”

34⁄”

(884mm)

13⁄”

(345mm)

27⁄”

(700mm)

Keep this air ﬂow area free of obstructions

2. Check the inside of the RV for return air kit obstructions.

(i.e. door openings, room dividers, curtains, ceiling fixtures,

etc.) Allow 6” (152mm) space from the opening to account

for any potential return air kit obstructions.

Roof

Opening

17.5”

(438mm)

17.5”

(438mm)

19⁄”

(500mm)

19⁄”

(500mm)

Roof

Opening

17.5”

(438mm)

17.5”

(438mm)

⁄”

(500mm)

19⁄”

(500mm)

Roof Preparation

Opening Requirements - Before preparing the ceiling opening,

decide on the type of system options. Read all of the following

instructions before beginning the installation.

WARNING

Fire/Electric Shock Hazard

●Make sure there are no obstacles inside the RV roof, floor

and walls, such as wires and pipes.

●Shut off the gas supply and disconnect the 115VAC

power from the RV before drilling or cutting into the RV.

Failure to obey these warnings could result in death or

serious injury.

Roof Thickness

The installation of air conditioner suits for roof thickness from

3.5” (90mm) to 6” (152mm). For other thickness, please contact

Furrion or Furrion authorized service agent.

Installing in an Existing Opening

1. Unscrew and remove the roof vent.

2. Remove all caulking compound around the opening.

3. If the opening exceeds 14¼” x 14¼” (+½”), it will be

necessary to resize the opening to 14¼” x 14¼” (+½”). If the

opening is less than 14¼” x 14¼” (+½”), it must be enlarged.

362mm

14¼”

362mm

14¼”

362mm

14¼”

362mm

14¼”

Making a New Opening

If a roof vent opening will not be used, a 14¼” x 14¼” (+½”)

(362mm x 362mm) opening must be cut through the roof and

ceiling of the RV. This opening must be located between the

roof reinforcing members.

The 14¼” x 14¼” (+½”) opening is part of the return air system

of the air conditioner and must be finished in accordance with

NFPA Standard 501C Section 2.7.2.

1. Mark a 14¼” x 14¼” (+½”) square on the roof and carefully

cut an opening.

362mm

14¼”

362mm

14¼”

362mm

14¼”

362mm

14¼”

2. Using the roof opening as a guide, cut a matching hole in

the ceiling.

NOTE: Maintain structural integrity. Otherwise damage

to product and/or RV could occur. Always observe the

following guidelines while structuring the opening.

Do not cut roof

structure or

rafters

Good: rafters

supported by

cross beams

Good: location

between roof

rafters

3⁄4" Min.

(19.05 mm)

Leave access for

power supply wiring

3. The opening created must be framed to provide adequate

support and prevent air from being drawn from the roof cavity.

4. Lumber ¾” or more in thickness must be used. Remember

to provide an entrance hole for power supplies, wall

thermostat and furnace wiring for connections. Leave 15”

(381mm) minimum at the front of the opening.

English

CCD-0005730 Rev: 04-25-22

- 4 -

Do not cut roof

structure or

rafters

Good: rafters

supported by

cross beams

Good: location

between roof

rafters

3⁄4" Min.

(19.05 mm)

Leave access for

power supply wiring

Air Distribution Duct Sizing and Design

The installer of this system must design the air distribution

system for their particular application.

NOTE: Make sure ductwork will NOT bend or collapse during

and after installation, and that it is correctly insulated and

sealed. Otherwise, damage to roof structure and ceiling could

occur.

The following requirements must be met for properly operate

the unit:

Roof Cavity Depth 3.5"-6" (89mm-152mm)

Duct Cross

Sectional Area 21 Sq. In. Min.

Duct Size

Depth 1½" Min. - 2½" Max. (38mm

Min. - 63.5mm Max.)

Width 7" Min. - 10" Max. (178mm

Min. - 254mm Max.)

Total Duct Length 15Ft. Min. - 40Ft. Max. (4.5m

- 13m)

Duct Length (short run) 1/3 Total Duct Length

Requirements per

A/C Unit

Number Required 4 Min. - 8 Max.

Supply Register Free

Air Area 14 Sq. In. (90 sq. cm)

Return Register Free

Air Area 40 Sq. In. (258 sq. cm)

Distance From Duct

End

5" Min. - 8" Max. (127mm

Min. - 203mm Max.)

Distance From Elbow 15" (381mm)

Total System Static

Air Pressure

Blower at High Speed,

Filter & Grille In Place 0.55 - 1.10 In. W.C.

●Properly insulate and seal all discharge air ducts to prevent

condensation from forming on their surfaces or adjacent

surfaces during operation of the unit. This insulation must

be R-7 minimum.

Frame

DuctDuct

Frame

Roof

Opening

Roof Opening

Roof

Duct Ceiling Duct

TOP VIEW (BACK OF RV)

SIDE VIEW (TOWARD BACK OF RV)

●Return air openings must have 80 square inches (516

square centimeters) minimum free area including the filter.

●Return air to the unit must be filtered to prevent dirt

accumulation on the unit cooling surface.

Air Distribution System Installation

It is the responsibility of the installer to review each RV floor

plan to determine the following items in conjunction with “Air

Distribution Duct Sizing and Design” section

NOTE: Alternate configurations and methods may be used

which will allow the unit to operate properly, however, these

alternate configurations and methods MUST be approved by

Furrion in writing.

●Duct size

●Duct layout

●Register size

●Register location

●Thermostat location

●Indoor temperature sensor location (if applicable)

Front

Registers 4

Min - 8 Max.

(Per Unit) 14

Sq. In. Free

Area Per

Air Conditioner

Return Air

Preparing Wire Connections

Each rooftop air conditioner opening must be prepared

with proper wiring to connect the ceiling controller of the air

conditioner to the 115VAC and 12VDC supply voltage, wall

thermostat and furnace switch.

NOTE: The wire connections need to be positioned in the

forward facing 1/4 section of the opening.

DANGER

Electrical Shock Hazard

●Disconnect power before servicing. Failure to obey this

warning could result in death or serious injury.

●Provide grounding in compliance with all applicable

electrical codes. Failure to obey this warning could result

in death or serious injury.

115VAC Supply

1. Prepare a dedicated 20 amp rated circuit for each air

conditioner unit, protected with a time delay fuse or circuit

breaker.

NOTE: With multiple air conditioners on a 50 amp service,

it is best to balance between the line voltage legs.

2. Extend circuit with a 12AWG 2-wire with ground to the roof

opening.

NOTE: The wire gauge is generally acceptable per NEC

code, refer to rooftop unit nameplate and applicable code

for proper sizing.

3. Protect the wire where it passes through any rough

English

CCD-0005730 Rev: 04-25-22 - 5 -

surfaces or openings.

4. Terminate with at least 15” (381mm) of supply wire

extending out of the roof opening. This ensures an easy

connection at the control box.

12VDC Supply

1. Prepare a 15 amp max protected circuit to supply power to

all air conditioner units.

NOTE: The branch circuit can be dedicated or shared with

other utilization equipment.

2. Extend circuit with a 14AWG 2-wire, (12V+, 12V-) to each

roof opening.

3. Protect the wire where it passes through any rough

surfaces or openings.

4. Terminate with at least 15” (381mm) of supply wire

extending out of the roof opening. This ensures an easy

connection at the control box.

Wall Controller Connection (Single and

Multizone Thermostat)

1. Prepare 4 wires to connect between the ceiling controller

(roof opening) and wall controller/thermostat (wall

opening).

NOTE: 18AWG max should be used, Furrion recommends

using a standard thermostat wire with at least 4-wires.

2. Terminate with at least 15” (381mm) of wire end for easy

connection.

3. For Multizone installations, prepare additional wiring of the

same type to connect between each roof opening.

Furnace Switch (Optional)

1. If required to operate the furnace using the air conditioner

wall controller/ thermostat, prepare 2-wires in the roof

opening to connect the desired ceiling control zone with

the furnace’s thermostat circuit.

NOTE: This serves as a 12V+ line, that becomes hot only

when the ceiling controller closes the furnace switch to

turn the furnace on.

2. Terminate with at least 15” (381mm) of wire at each end for

easy connection.

INSTALLATION

Installing the Rooftop Unit

CAUTION

●The rooftop unit weighs approximately 100 pounds (45

kg). To prevent back injury, use a mechanical hoist when

lifting or moving the unit. Failure to obey this warning

could result in injury.

●Do not slide unit. It may damage the gasket at the bottom

of the rooftop unit and cause leakage.

●Do not grasp the ventilation slots to lift the rooftop unit

up.

Hold the bottom of the unit, lift and position the rooftop unit into

the prepared opening using the gasket at the bottom of the

rooftop unit as a guide.

Roof Opening

This Side is

Facing Forward

This completes the outside installation of the rooftop unit.

Minor adjustments can be done from inside of the RV if

required.

Installing the Wall Thermostat

Furrion provides 2 types of wall thermostats (sold separately)

in different functionalities:

●Single zone wall thermostat

●Multi zone wall thermostat

Based on the wall thermostat version you selected. Please

refer to the separate instruction manual on how to install the

wall thermostat to the RV.

Installing the Air Distribution Box

NOTE: The installation of the air distribution box is same for

both ducted and non-ducted structures.

The rooftop unit is fixed on the RV roof using 4 long bolts

through the mounting frame from the interior of the RV ceiling.

1. Check the gasket alignment of the rooftop unit inside the

RV over the roof opening and adjust as necessary by lifting

and moving slightly.

Roof Opening

2. Reach up into the return air opening and pull down the

rooftop unit electric cord. Ensure all terminated wire ends

specified in “Preparing Wire Connections” section are

accessible.

English

CCD-0005730 Rev: 04-25-22

- 6 -

Rooftop Unit

Cable

115VAC

Power Cord ±12VDC

Wires

Thermostat Wire

(4-wire min.)

Return to Furnace

(optional)

12V+ from Furnace

(optional)

Roof Opening

3. Assemble the lower duct divider to the mounting frame.

4. Install the assembled mounting frame and the lower duct

divider into the rooftop opening. Make sure the “THIS WAY

FRONT” mark is facing front (the direction of the vehicle)

while installing.

5. Fix the assembled mounting frame and lower duct divider

into the rooftop unit using 4 bolts provided. Evenly tighten

the four bolts to a torque of 40 to 50 inch pounds. This will

compress the roof gasket to approximately ½”.

NOTE: If bolts are left loose there may not be an adequate

roof seal or if over tightened, damage may occur to the

rooftop base or mounting frame.

6. Remove the film off the double sided sticky tape found on

the top inner side of the lower duct divider.

Peel o the ﬁlm

7. Stick the upper duct divider into the assembled mounting

frame.

NOTE: Make sure the upper duct divider is compressing

the top foam on the base of the air conditioner unit, and

compress tightly to the doubled sided tape on the lower

duct divider to ensure a positive retention.

Upper duct divider

8. Use self adhesive foil tape to seal the two halves of the

duct divider together and any potential gaps around the

duct divider to roof opening that may allow cold air to leak

back into the warm intake side.

NOTE: Clean metal surfaces to remove any oils to ensure

good adhesion of the foil tape.

English

CCD-0005730 Rev: 04-25-22 - 7 -

Foil tape

9. Measure the height of the duct divider, and cut the PE foam

with a utility knife to the measured dimension. Peel paper

backer of foam to reveal sticky adhesive. Evenly adhere PE

condensation foam to duct divider, working material into

crevices and surfaces for a tight uniform fit across the duct

divider surface.

Duct Divider Height

PE Foam

Measured Duct

Divider Height

DIP Switch Settings

The DIP switches enable/disable different communications

between the ceiling controller and wall thermostat for functions

such as, zone selection, furnace operation, and additional

accessories.

The controls are preset with the following active DIP switch

settings:

Single Zone: Furnace on (FACC12SA-BL)

Multi Zone: Zone 1; Furnace on (FACC12ZA-BL, FACC12NA-

BL, FACC12ESZA, FACC12ZA, FACC12HE, FACC12ESHE

Location of the DIP Switch

The DIP switches are located on the PCB board of the control

box. Each time you want to set the DIP, you should open the

control box and find the DIP switches.

1. Remove the cover of the control box, and find the PCB

board.

2. Locate the position of the DIP switches on the PCB board.

DIP Switches Location

PCB Board Location

Setting DIP Switches

DANGER

Electrical Shock Hazard

Disconnect power before servicing. Failure to obey this

warning could result in death or serious injury.

1. Remove power when setting dip switches, make sure all

115VAC and 12VDC power to the control board is removed.

2. Use a small tool, slide the dip switch to either ON/OFF.

NOTE: If 12V+ is present when making a setting change, It will

be is necessary to cycle power to reset the control to make the

setting active.

Single Zone DIP Switches:

3456

Heat Pump

(selected models) DIP 3 Reserved

Furnace DIP 4 OFF Furnace Off

ON Furnace On

Electric Heat

(selected models) DIP 5 OFF Electric Heat Off

ON Electric Heat On

Analog / Digital DIP 6 OFF Digital

ON Analog

Multi Zone DIP Switches:

●Each zone requires an independent ceiling control box, but

will share one wall thermostat control.

●It is important that each independent zone is set to a

unique zone value (1-4) by setting the DIP 1 and DIP 2 to

avoid repetition and communication conflicts with the wall

thermostat control.

English

CCD-0005730 Rev: 04-25-22

- 8 -

123456

Zone Selection*

DIP 1 DIP 2 ZONE Setting

OFF OFF ZONE1

OFF ON ZONE2

ON OFF ZONE3

ON ON ZONE4

Heat Pump

(selected models) DIP 3 Reserved

Furnace DIP 4

OFF Furnace Off

ON Furnace On

Electric Heat

(selected models) DIP 5

OFF Electric Heat

Off

ON Electric Heat

Analog / Digital DIP 6 OFF Digital

ON Analog

Wire Connection - Digital Furrion Wall

Controller/Thermostat

DANGER

Electrical Shock Hazard

●Disconnect power before servicing.

●Provide grounding in compliance with all applicable

electrical codes.

Failure to obey this warning could result in death or serious

injury.

1. Familiarize yourself with the ceiling controller and wire

harnesses.

NOTE: When connecting to a Furrion wall controller/

thermostat, the analog harness bundle is not used and can

be tucked away. The ends do not need to be capped or

taped.

Wall Thermostat Cable

(4-wire harness)

Analog Cable (8-wire

harness)

Furnace Cable (2-wires)

12V DC Power Cable (2-wires)

Freeze Sensor Cable (wire with

copper tip and blue plastic clip)

LED Cable (1 white

cable)

2. Loosen the strain relief and compartment cover of the

control box and pass the 115VAC power cord through

the strain relief hole and re-tighten the cable clamp until

properly restrained. Do not over tighten.

3. Make wire connections following the below color codes.

Black - Hot

White - Neutral

Green/yellow - Ground

Strain Relief

4. Fit all cables into the cable compartment and tuck any

excess wires up out of the way. Tighten the cover with

screw.

5. Locate the four thermostat cables of the control box (red,

green, blue and purple), which are tied together and tagged

with “To wall thermostat”, and connect them to the

thermostat wire that extends to the wall.

IMPORTANT: Note the function marked on the wire end

and carefully trace and mark its function at the end of the

wire extension so that proper connection can be made at

the wall controller / thermostat.

Crossing the wires could prevent the control from

operating properly, or even cause damage. If uncertain,

perform a continuity test through each extension to

confirm.

Thermostat Cable

6. If applicable, locate the furnace wires from the ceiling

controller, which are two separate brown wires tagged

with “FURN”. Connect them with the 12V+ wire from the

furnace, and the return wire to the furnace.

NOTE: Polarity does not matter, connection can be freely

made to either wire. Do not connect the two brown “FURN”

wires together.

English

CCD-0005730 Rev: 04-25-22 - 9 -

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Lippert Klimaanlage Handbücher

Lippert

Lippert Furrion FACB09HM Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung