Litelume Wallpack-Adjustable Bedienungsanleitung
Wallpack-Adjustable
Installation Instructions
LITELUME™ seeks to deliver the most advanced and efficient LED technology. Due to
technology progression, specifications may change. We reserve the right to update product
specifications without notice. Contact LITELUME™ for the most up-to-date data.
www.litelume.com
833.LED.LUME
Page 1/2
Rev Date: 05/6/2020
©Lite Lume Corporation 2018
Warning
1.To avoid electric shock, disconnect power at source prior to installation.
2.The installation should be performed by qualified electricians or lighting technicians.
3.Before conducting any installation, maintenance, or removal, disable all power to the luminaries and wait until the fixture cool
down.
4.Do not touch the fixture while it is in service.
5.If there is any problem with the fixture, DO turn off power and DO NOT attempt repair unless you are a qualified technician or
the customer service member.
Installation
1. Open the Back Box by loosening the Locking Screw.
2. Verify and remove only necessary Gasket material where Back Box will mount.
3. Knock-out Back Box material for necessary mounting location.
4. Mount Back Box to Junction Box securely, using hardware supplied by others.
5. Connect electrical connections with fixture wiring.
6. Seal Back Box to Housing by pushing on front of Housing while tightening
- Locking Screw to ensure that screw is fully seated in the Housing Recess.
-Ensure wiring remains within Back Box and wires do not get pinched.
-Using a silicone rubber will ensure a watertight seal.
Wall Mount Box
150mm
135mm
151.3mm
5.31 ’’
5.96 ’’
5.9 ’’
Leveling Bubble
Hands-free
mounting hinge
Body
Wall Mount Box
G 1/2 Close Up Plugs
Photocell
EVA Gasket
Glass
Sealing ring
Serrated Safety
Washers Screw
Adjusting angle screw Screw
7. If light output angle needs to be adjusted loosen screw to rotate the fixture to desired light output angle. Tighten screw once
desired light output angle is achieved.
0° 60° 90°
Wallpack-Adjustable
Installation Instructions
LITELUME™ seeks to deliver the most advanced and efficient LED technology. Due to
technology progression, specifications may change. We reserve the right to update product
specifications without notice. Contact LITELUME™ for the most up-to-date data.
www.litelume.com
833.LED.LUME
Page 2/2
Rev Date: 05/6/2020
©Lite Lume Corporation 2018
ON-OFF Wiring
Universal voltage driver permits operation at 120V to 277VAC, 60 Hz except fixtures factory ordered with a 120V photocell (P1) or
277V photocell (P2) or 347V photocell (P3)
1. Connect the Black fixture lead to the (+) LINE supply lead.
2. Connect the White fixture lead to the (-) COMMON supply lead.
3. Connect the Yellow/Green wire from fixture to supply ground.
Black
White Neutral
Green/Yellow Green
Ground
Line
Purple
DIM+
Gray
DIM-
Photocell Installation
1. Install photocell and wire as per diagram.
2. Use photocell rated for your supply voltage.
BLACK
BLACKBLACK
AC
INPUT
LAMPLOAD
RED
PHOTOCONTROL
WHITE
WHITEWHITE
Cleaning and Maintenance
CAUTION: Be sure the fixture temperature is cool enough to touch. Do not clean or maintain while fixture is energized.
1. Clean glass lens with non-abrasive glass cleaning solution.
2. Do not open the fixture to clean the LED. Do no touch the LEDs.
Troubleshooting
1. Check that the line voltage at the fixture is correct. Refer to wiring diagram above.
2. Is the fixture grounded properly?
3. Be sure the photocell, if used, is functioning properly.
Inhaltsverzeichnis
Andere Litelume Beleuchtungsausrüstung Handbücher
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
