Lithonia Lighting EU2C Bedienungsanleitung
DO NOT PRINT with INSTRUCTIONS
DO NOT PRINT with INSTRUCTIONS
Information below is for LITHONIAdocumentation purposes only.
DO NOT include this page in the printing of this instruction sheet.
PART NUMBER: EMCSA00911
DESCRIPTION: INSTRUCTION SHEET, EU2C
SPECIFICATIONS: Prints 8.5 x 11, portrait. Two side, one color: BLACK ink.
PAGINATION: 8.5” X 11 portrait.
CONFIGURATIONS
PART # INSTRUCT SHEET DESCRIPTION REV DATE STANDARD UNIT
EU2C B09.12.2018 X
EMCSA00795 ABLLED WARNING X
DATE CHANGE DESCRIPTION BY
One Lithonia Way, Conyers GA30012
Phone: 800-334-8694
www.lithonia.com
PAGE: 0 of 4
RRB
HO
X
X
9.12.18REV. B: Removed SD HO wiring diagram - ABL not offering SD and hO together at this time.
REQUIRED INSTRUCTION SHEETS for EU2C models
EMCSA00912
EMCSA00911
A08.06.2018
SDT
X
X
SD INSTRUCTIONS
RRM
8.06.18REV. A: Initial Release
INSTALLATION INSTRUCTIONS for Lithonia Lighting EU2C Models
SAVE THESE INSTRUCTIONS
and deliver to owner after installation
LED DUAL HEAD EMERGENCY LIGHTING FIXTURE
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
WARNING:
FAILURE TO FOLLOW THESE INSTRUCTIONS
AND WARNINGS MAY RESULTIN DEATH, SERIOUS INJURYOR
SIGNIFICANT PROPERTY DAMAGE. For your protection, read and
follow these warnings and instructions carefully before installing or
maintaining this equipment. These instructions do not attempt to cover
all installation and maintenance situations. If you do not understand
these instructions or additional information is required, contact
LITHONIALIGHTING or your local LITHONIALIGHTING distributor.
WARNING: RISK OF ELECTRIC SHOCK - NEVER CONNECT
TO, DISCONNECTFROM, OR SERVICE WHILE EQUIPMENTIS
ENERGIZED.
WARNING: RISK OF FIRE. Lamps are hot. Keep combustible material away from hot parts. Observe lamp manufacturer’s warnings,
recommendations and restrictions on lamp operation and maintenance. Make sure lamps are correctly installed.
CAUTION: The battery in this unit may not be fully charged.After electricity is connected to unit, let battery charge for at least 24
hours, then normal operation of this unit should take effect.To check, press the TEST button.The lamps on the unit should turn on.
IMPORTANT SAFEGUARDS: When using electrical equipment, basic safety precautions should
always be followed, including the following:
PAGE: 1 of 4
Fig.A (J-Box) Fig.B Fig.C
BATTERY CONNECTOR
PLUG IN
NOTE:Complies with California Title 20. Product label is marked with .
INSTALLATION:
NOTE: Max mounting height is 10 ft to achieve at least 1 ft-candle of illuminance in emergency mode.
• Do not use outdoors.
• Consult local building code for approved wiring and installation.
• DisconnectAC power before servicing and installation.
• Do not mount near gas or electric heaters.
• Do not use this equipment for anything other than its intended use.
•
Theuse of accessoryequipmentnotrecommendedby the manufacturer will voidproductlistingandwarranty and maycauseanunsafe condition.
• Any service on this equipment should be performed by qualified personnel only.
• Equipment should be mounted in locations and at heights where it will not be subject to tampering by unauthorized personnel.
•Do not ceiling mount.
• Use caution when servicing batteries.
• Cap unused wires with enclosed wire nuts or other approved method.
• Make sure wire terminations are secure and leads are properly tucked in appropriate wire channels.
INSTALLATION INSTRUCTIONS
J-BOX MOUNTING:
1.
Feed fixture leads through the back plate and connect to AC power supply (Fig A, page 1). For 120V use black and white wires
and for 277V, use red and white wires.
2.
Attach back plate to J-Box and secure with screws.
3.
Complete the battery connection. (Fig. B, page 1)
4.
Align snaps and push housing directly onto the back plate (Fig. C, page 1).Apply continuousAC power.
5.
After the battery has been left to charge for 24 hours, test the unit by pushing the test switch and the LED lamp head will turn ON.
CONDUIT MOUNTING:
1. Secure back plate to wall surface using keyhole knockouts on the back plate.
2. Route wires through hole in conduit flange and make conduit connection. For 120V use black and white wires and for 277V, use
red and white wires.
3. Complete the battery connection (Fig. B, page 1).
4. Align snaps and push housing directly onto the back plate. Apply continuous AC power.
5. After battery has been left to charge for 24 hours, test the unit by pushing the test switch and the LED lamp head will turn ON.
WALLMOUNTING:
SAVE THESE INSTRUCTIONS
and deliver to owner after installation
PAGE:2of 4
1. Secure back plate to wall surface using keyhole knockouts on the back plate.
2. Feed fixture leads through back plate and connect to AC power supply. For 120V use black and white wires and for 277V, use
red and white wires.
3. Complete the battery connection (Fig. B, page 1).
4. Align snaps and push housing directly onto the back plate. Apply continuous AC power.
5. After battery has been left to charge for 24 hours, test the unit by pushing the test switch and the LED lamp head will turn ON.
OPERATION:
1. During an electrical power failure, the LED lamps will automatically come on for a minimum of 90 minutes.
2. To test, press the "TEST" switch. The emergency LED lamps will illuminate and LED indicator will turn OFF. When the switch
is released, the lamps will turn OFF and the LED indicator will turn ON.
LED STATUS INDICATOR KEY and TROUBLESHOOTING:
Visual Status Indicaon Troubleshoong/Acons to Take
RED
GREEN
UNLIT
1. Baery connecon is not made.
2. Baery has been diagnosed as dead or defecve aer 24
hours of connuous charging with AC power supplied.
Baery is connected, AC power has been supplied and xture is in
charging state.
AC power has not been supplied.
1. Make connecon; or if baery is connected, disconnect
battery for eight seconds and then reconnect.
2. Replace the battery.
This is the normal state. No acon required.
Supply AC power.
TESTING:
National Electric Code (NEC) and NFPA101regulations require that routine tests need to be performed as listed below: Once every
month, the unit needs to be tested for duration of 30 seconds. Push in and hold the test switch to perform this test. Once every 12
months, a full 90 minute (per UL requirements) test needs to be performed on the unit. Disconnect power to the unit and leave it in
the emergency mode. The lamps should stay ON for at least 90 minutes. Written records of the testing are to be kept for
examination by the authority having jurisdiction.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
WIRING DIAGRAMS
REMOTE CAPABLE
BLUE(-)
YELLOW(+)
BLUE(-)
BLUE(-)
YELLOW(+)
LAMP
YELLOW(+)
LAMP
READY
TEST
BATTERY
BLACK
Note:
Unused input lead must
be properly insulated with
wire nut or other approved
method.
RED
RED
BLACK
WHITE
277V
120V
0V
CHARGER
BOARD
LAMP
READY
TEST
BATTERY
RED
BLACK
RED
BLACK
WHITE
277V
120V
0V
LAMP
YELLOW(+)
BLUE(-)
YELLOW(+)
BLUE(-)
CHARGER
BOARD
AC INPUT CONNECTOR
(MOUNTING PLATE)
AC INPUT CONNECTOR
(MOUNTING PLATE)
TO REMOTE
Note for HO models:
Use 18-22 AWG stranded
wire to connect remote lamp
heads.
SAVE THESE INSTRUCTIONS
and deliver to owner after installation
PAGE:3 of4
Condition - Emergency lights are dim
1. Battery not fully charged.Allow battery to recharge for 24 hours and then retest. If lights are still dim, replace battery.
TROUBLESHOOTING:
Condition - The emergency lights do not operate
1. If the charge indicator light is OFF: Check that the circuit breaker forAC supply is ON.
2. If the charge indicator light is ON: Check that battery is properly connected. If problem persists, Replace battery. If remote lamps (where appli-
cable) are connected to the equipment, then turn OFF theAC supply and disconnect the remote circuit wires from the equipment. Turn ON the
AC supply and depress the test switch. If the local lamps (mounted on the equipment itself) come ON, then check the remote circuit for short or
overload condition and correct as required. Reconnect the circuit wires and restoreAC power. If the local lamps don’t turn ON after disconnecting
the remote circuit wires, then replace battery.
INSTALLATION INSTRUCTIONS
SAVE THESE INSTRUCTIONS
and deliver to owner after installation
PAGE: 4of 4
One Lithonia Way, Conyers GA30012
Phone: 800-334-8694
www.lithonia.com Part No. EMCSA00911, REV B
2018.09.12
AC INPUT CONNECTOR
(MOUNTING PLATE)
LAMP
READY
TEST BATTERY
RED
BLACK
WHITE
YELLOW(+)
BLUE(-)
WHITE
YELLOW(+)
BLUE(-)
LAMP
RED
BLACK
WHITE
277V
120V
0V
CHARGER
BOARD
Inhaltsverzeichnis
Andere Lithonia Lighting Beleuchtungsausrüstung Handbücher
Lithonia Lighting
Lithonia Lighting EDGR Bedienungsanleitung
Lithonia Lighting
Lithonia Lighting PreCise ELA LCRIS Series Bedienungsanleitung
Lithonia Lighting
Lithonia Lighting LHXNY Bedienungsanleitung
Lithonia Lighting
Lithonia Lighting CUC8 Bedienungsanleitung
Lithonia Lighting
Lithonia Lighting TFR Series Bedienungsanleitung
Lithonia Lighting
Lithonia Lighting DSX0 Bedienungsanleitung
Lithonia Lighting
Lithonia Lighting LEM04 Bedienungsanleitung
Lithonia Lighting
Lithonia Lighting OFL2WG Bedienungsanleitung
Lithonia Lighting
Lithonia Lighting JCBL Series Bedienungsanleitung
Lithonia Lighting
Lithonia Lighting CPRB 18LM MVOLT Bedienungsanleitung
Lithonia Lighting
Lithonia Lighting ECBG LED M6 Bedienungsanleitung
Lithonia Lighting
Lithonia Lighting KBA Bedienungsanleitung
Lithonia Lighting
Lithonia Lighting LZ Series Bedienungsanleitung
Lithonia Lighting
Lithonia Lighting EXTREME LVS2 120/277 ELN SD Series Betriebsanleitung
Lithonia Lighting
Lithonia Lighting ELU 4 Bedienungsanleitung
Lithonia Lighting
Lithonia Lighting WST LED Bedienungsanleitung
Lithonia Lighting
Lithonia Lighting Affinity Montageanleitung
Lithonia Lighting
Lithonia Lighting WPX1 LED Bedienungsanleitung
Lithonia Lighting
Lithonia Lighting KVF Series Bedienungsanleitung
Lithonia Lighting
Lithonia Lighting TWA Bedienungsanleitung
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
