Littelfuse Zilog Z8 Encore! XP F3224 Series Bedienungsanleitung

Z8F32240100ZCOG

Z8 Encore! XP® F3224

Series Development

Kit

User Manual

UM029101-0421

Z8 Encore! XP® F3224 Series Development Kit

UM029101-0421

User Manual

LIFE SUPPORT POLICY

ZILOG’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPO-

NENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS

PRIOR WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF

ZILOG CORPORATION.

As used herein

Life support devices or systems are devices which (a) are intended for surgical implant into

the body, or (b) support or sustain life and whose failure to perform when properly used in

accordance with instructions for use provided in the labelling can be reasonably expected

to result in a significant injury to the user. A critical component is any component in a life

support device or system whose failure to perform can be reasonably expected to cause

the failure of the life support device or system or to affect its safety or effectiveness.

Document Disclaimer

applications, or technology described is intended to suggest possible uses and may be

superseded. ZILOG, INC. DOES NOT ASSUME LIABILITY FOR OR PROVIDE A

REPRESENTATION OF ACCURACY OF THE INFORMATION, DEVICES, OR

TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZILOG ALSO DOES NOT ASSUME

LIABILITY FOR INTELLECTUAL PROPERTY INFRINGEMENT RELATED IN ANY

MANNER TO USE OF INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED

HEREIN OR OTHERWISE. The information contained within this document has been

verified according to the general principles of electrical and mechanical engineering.

Z8 Encore!, Z8 Encore! XP, ZMOTION, eZ80Acclaim! and ZNEO are trademarks or

registered trademarks of Zilog, Inc. All other product or service names are the property of

their respective owners.

Warning: DO NOT USE THIS PRODUCT IN LIFE SUPPORT SYSTEMS.

Z8 Encore! XP® F3224 Series Development Kit

UM029101-0421 OVERVIEW

User Manual

Overview

This document describes the features of the Z8 Encore! XP F3224 Series Development Kit

(Z8F32240100ZCOG) and provides instructions to setup the hardware and to install the software drivers

and development tools needed to start building applications.

The development board features the Z8F3224 MCU with 32KB internal Flash in a 44-pin QFN package

operating at 20MHz. Z8F3224 serial peripheral devices (SPI, I2C, UART) can be used to interface with

the 64Mb serial Flash (SPI) and optical sensor (I2C) available on the development board, or external

devices (header pins). Refer to the Z8 Encore! XP® F3224 Series Product Specification (PS0381)

available for download at www.zilog.com for information on these and other F3224 peripheral

devices.

Subsequent sections of this document guide you through the following tasks:

•Download and Install the ZDS II Software and Documentation –see page 4

−Installing the Encore! Smart Cable Driver –see Appendix B. Installing the Encore! Smart

Cable Driver on page 16

•Connect F3224 Series Dev Board to PC –see page 5

•Start Z8F3224 Demonstration Program –see page 7

Further details, including memory configurations, jumper settings, and a listing of sample projects can be

found in the Z8F3224 Sample Projects section on page 12.

Figure 1 shows an image of the F3224 Series Development Kit.

Z8 Encore! XP® F3224 Series Development Kit

UM029101-0421 OVERVIEW

User Manual

Figure 1. The F3224 Series Development Kit

Z8 Encore! XP® F3224 Series Development Kit

UM029101-0421 KIT CONTENTS

User Manual

Kit Contents

Table 1 lists the contents of the F3224 Series Development Kit.

Table 1. Z8F32240100ZCOG Contents

Item

Description

Quantity

F3224 Series Development Board

Encore! Smart Cable

6-wire ribbon cable

A (male) to Mini-B USB cable

F3224 Series Development Kit Flyer (FL0193)

Kit Features

The key features of the F3224 Series Development Kit are:

•F3224 Series Development Board, which includes:

−Z8F3224QN020XK MCU in 44-pin QFN package operating at 20 MHz

−UART port J3

−Test points and headers

−Four LEDs (Power and Port Display)

−Two pushbuttons (Reset and Test)

−Smart Cable Debug Interface J5

•Encore! Smart Cable (ESC)

•ZDS II development tools, sample projects, and documentation available free for download

Z8 Encore! XP® F3224 Series Development Kit

UM029101-0421 SYSTEM REQUIREMENTS

User Manual

System Requirements

The F3224 Series Development Board supports the following operating systems:

•Microsoft Windows 7, (32-bit/64-bit)

•Microsoft Windows 8 (32-bit/64-bit)

•Microsoft Windows 10 (32-bit/64-bit)

Download and Install ZDSII SW and Docs

Observe the following steps to install ZDS II software and documentation.

Note: If you have already downloaded and installed the ZDS II –Z8 Encore! <version> development tools and

documentation by following the procedure on the paper insert in your kit (FL0193), then you’re ready for

Appendix B. Installing the Encore! Smart Cable Driver on page 16.

1. Prior to connecting the Z8 Encore! XP F3224 Series Development Board to your development

PC, download ZDS II for Z8 Encore! v5.6.0 (or later) from the Zilog Software Downloads

category in the Zilog website.

2. When your download is complete, unzip the file to your local drive, then double-click the

installation file named ZDS2_Z8Encore!_<version>.exe, and follow the on-screen

instructions.

3. When the ZDS II installation is complete, click the supporting documentation link on Zilog Software

Downloads. This will download the documentation installer as a ZIP file. Unzip and double click on

docs_Z8Encore!_<version>.exe and follow the on-screen instructions.

Z8 Encore! XP® F3224 Series Development Kit

UM029101-0421 CONNECT F3224 SERIES DEV BOARD TO PC

User Manual

Connect F3224 Series Dev Board to PC

Observe the following procedure to connect the F3224 Series Development Board to your PC.

Caution: The USB Smart Cable can be configured to supply power to the F3224 Series Development Board,

or an external power source may be used to power the board. When external power is used, be

sure to disconnect or turn off the external power source before connecting or disconnecting the

Encore! Smart Cable from the development board.

1. Connect one end of the ribbon cable to the Encore! Smart Cable ensuring the ridge on the

ribbon cable’s female connector is aligned with the notch in the shrouded male connector on

the Smart Cable as shown in Figure 2.

Figure 2. Connecting the 6-Circuit Ribbon Cable to the Encore! SmartCable

2. Connect the other end of the ribbon cable to Debug Connector J5 on the Development Board.

Ensure that Pin 1 on the ribbon cable (red stripe) is aligned with Pin 1 on the target connector

(square pad), as highlighted in Figure 3.

Z8 Encore! XP® F3224 Series Development Kit

UM029101-0421 CONNECT F3224 SERIES DEV BOARD TO PC

User Manual

Figure 3. Debug Connector J5

Z8 Encore! XP® F3224 Series Development Kit

UM029101-0421 START Z8F3224 DEMONSTRATION PROGRAM

User Manual

Start Z8F3224 Demonstration Program

The F3224 Series Development Kit includes a sample program that demonstrates a blinking LED

application with a UART console. An optional terminal emulation program and a 3rd Party USB to TTL

Serial converter (not supplied) maybe used to display the messages and send characters to the

application. In this instance, the terminal program must be configured for 57600-8-N-1 with no flow

control, as described in the Terminal Emulation Configuration section on page 10. To get started with the

Z8F3224 demonstration, observe the following procedure.

1. Launch ZDS II by navigating from the Windows Start menu to Programs → Zilog ZDS II –Z8

Encore! <version> → ZDS II –Z8 Encore! <version>.

2. From the File menu in ZDS II, select Open Project and navigate to the following folder:

<ZDS Install>\samples\XP_F3224\XP_F3224_LedBlink_C

3. Select the ledblink.zdsproj project from within the XP_F3224_LedBlink_C folder and click

Open.

4. From the Build menu, select Set Active Configuration to open the Select Configuration dialog

box.

5. Select Debug, then click OK to close the Select Configuration dialog box.

6. From the Project menu in ZDS II, select Settings to open the Project Settings dialog box. In the

Project Settings dialog box, click the Debugger tab.

7. On the Debugger page, select Z8F32240100ZCOG from the Target list, then select

EncoreSmartCable from the Debug Tool drop-down menu, as shown in Figure 4.

Z8 Encore! XP® F3224 Series Development Kit

UM029101-0421 START Z8F3224 DEMONSTRATION PROGRAM

User Manual

Figure 4. Select Z8F32240100ZCOG and EncoreSmartCable

8. Click Setup on Figure 5 below to open the Setup USB Communication dialog.

Figure 5. Setup EncoreSmartCable

9. Verify that a Serial Number is displayed in the Setup USB Communication dialog as shown in

Figure 6. If multiple Encore! Smart Cables are connected to the PC, click the chevron to display

the serial number of each Smart Cables and select which to use when programming or

debugging the target. If no serial numbers are displayed, verify that the Encore! Smart Cable is

attached to the PC and see Appendix B. Installing the Encore! Smart Cable Driver for instructions on

installing the necessary device drivers.

Inhaltsverzeichnis

Andere Littelfuse Mikrocontroller Handbücher

Littelfuse

Littelfuse zilog ZMOTIONL400ZCOG Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung