LMI Technologies Gocator 2375 Bedienungsanleitung
USERMANUAL
Gocator 2375 (Supplemental)
Document revision:A
Gocator 2375 2
Copyright
Copyright © 2015 by LMI Technologies, Inc. All rights reserved.
Proprietary
This document, submitted in confidence, contains proprietary information which shall not be
reproduced or transferred to other documents or disclosed to others or used for manufacturing or any
other purpose without prior written permission of LMI Technologies Inc.
No part of this publication may be copied, photocopied, reproduced, transmitted, transcribed, or
reduced to any electronic medium or machine readable form without prior written consent of LMI
Technologies, Inc.
Trademarks and Restrictions
Gocator™ is a registered trademark of LMI Technologies, Inc. Any other company or product names
mentioned herein may be trademarks of their respective owners.
Information contained within this manual is subject to change.
This product is designated for use solely as a component and as such it does not comply with the
standards relating to laser products specified in U.S. FDA CFR Title 21 Part 1040.
Contact Information
For more information, please contact LMI Technologies.
LMI Technologies, Inc. 1673 Cliveden Ave.
Delta, BC V3M 6V5
Canada
Telephone: +1 604 636 1011
Facsimile: +1 604 516 8368
www.lmi3D.com
Gocator 2375 4
Introduction
This documentation provides supplementary information for Gocator 2375.
See Gocator 2300 & 2880 Series User Manual for information on how to configure and use the Gocator
web interface with a Gocator 2375, as well as for reference information on the device's protocols and
configuration files. Sections cited from Gocator 2300 & 2880 Series User Manual are shown in italics.
Notational Conventions
This guide uses the following notational conventions:
Follow these safety guidelines to avoid potential injury or property damage.
Consider this information in order to make best use of the product.
Gocator 2375 Rut-Scanning System Setup • Layout • 5
Rut-Scanning System Setup
The following sections describe how to set up a rut-scanning system.
Layout
The Gocator 2375 is designed to cover a scan width of up to 4.2 m by using 8 sensors mounted in
parallel.
The diagram above shows the clearance distance and measurement range required in a typical setup.
You can use the specification estimator (Gocator-2375_Specification_Estimator.xlsx) to calculate the X
and Z resolution of the sensors with different combinations of clearance distance and measurement
range.
System Setup
A typical Gocator 2375 system is set up as a multi-sensor system. The sensors are powered up using a
Master 400/800/1200/2400.
Gocator 2375 Rut-Scanning System Setup • Software Configuration • 6
To wire up a Gocator 2375:
1. Connect the Gocator Power to Master cordset between the Power connector and an unused
port on the Master.
2. Connect the Gocator Ethernet cordset between the LAN connector and an Ethernet switch.
See the Master 400/800 and the Master 1200/2400 sections in Gocator 2300 & 2880 Series User Manual for
more information on how to install a Master.
Software Configuration
Each sensor is shipped with a default IP address of 192.168.1.10. Before you add a sensor to a multi-
sensor system, its firmware version must match that of the other sensors, and its IP address must be
unique.
All sections referenced in the following procedure are found in Gocator 2300 & 2880 Series User
Manual.
To configure a Gocator 2375 for the first time:
1. Set up the sensor’s IP address.
a. Follow the steps in the Running a Standalone Sensor System section.
b. Make sure that there is no other sensor in the network with the IP address 192.168.1.10.
2. Upgrade the firmware.
a. Follow the steps in the Firmware Upgrade section.
b. Visit http://www.lmi3d.com/support/downloads/gocator-2375-for-road-rut-scanning to download
the latest firmware.
Gocator 2375 Rut-Scanning System Setup • Software Configuration • 7
3. Set up profiling parameters.
a. Follow the steps in the Setup and Calibration section to set up profiling parameters. Typically,
trigger, active area, and exposure will need to be adjusted.
Gocator 2375 System Operation • 8
System Operation
An isolated layout should be used. Under this layout, each sensor can be independently controlled by
the SDK. The following application notes explain how to operate a multi-sensor system using the SDK.
APPNOTE_Gocator_4.x_Multi_Sensor_Guide.zip
Explains how to use the SDK to create a multi-sensor system, and multiplex their timing.
Gocator-2000-2300_appnote_multi-sensor-alignment-calibration.zip
Explains how to use the SDK to perform alignment calibration of a multi-sensor system.
Example code is included with both of the application notes above.
Gocator 2375 9
Specifications
For the specifications of the Gocator and associated hardware such as cordsets and Masters, see Gocator
2300 & 2880 Series User Manual.
Support
For assistance regarding a component or product, please contact LMI Technologies.
World
Email supp[email protected]
Web http://www.lmi3D.com
North America
Phone +1 604 636 1011
Fax +1 604 516 8368
Europe
Phone +31 45 850 7000
Fax +31 45 574 2500
For more information on safety and laser classifications, please contact:
U.S. Food and Drug Administration
Center for Devices and Radiological Health
WO66-G609
10903 New Hampshire Avenue
Silver Spring, MD 20993-0002
USA
Gocator 2375 10
Inhaltsverzeichnis
Andere LMI Technologies Beleuchtungsausrüstung Handbücher
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
