GB-1 GB-2 GB-3
MAX
1.2L
1.0L
MIN
1.5L
1.8L
UNPACKING
Remove all packaging from the unit. Retain the packaging. If you dispose of it
please do so according to local regulations.
The following items are included:
SWITCHING ON
• Place the kettle on its stand. Connect the
stand’s mains cable to the mains socket.
FIRST TIME USE
Clean your kettle by boiling a full kettle of water twice and then discarding the
water.
KEEPING THE MAINS CABLE TIDY
Extend the mains cable in the kettle stand
to the required length. Locate the mains
cable in the slot in the stand. For safety it
is recommended that the length of
exposed mains cable is kept as short as
possible.
PRODUCT OVERVIEW
• The Main Unit • Instruction Manual
(P.N.: LC17PKB_C_R12-002)
• Kettle Stand
(P.N.: LC17PKB_C_R12-SF)
• Never open the lid while the
water is boiling. The steam
coming out from the kettle is
very hot.
• If there is insufficient water in
the kettle, the automatic safety
cut-out will operate. If this
happens, allow the kettle to cool
for 10 minutes before relling
with cold water and re-boiling.
This kettle must only be used
with the stand provided.
MAX
1.2L
1.0L
MIN
1.5L
1.8L
MAX
1.2L
1.0L
MIN
1.5L
1.8L
Handle
Lid
Spout
Mains Cable
Water Fill Level
Kettle Stand
Power Switch
Mains
Cable
FILLING THE KETTLE
• Open the lid.
• Fill the kettle with the required amount of water.
• Do not exceed the maximum ll level (MAX 1.8L)
as indicated on the water ll level.
• Always ensure the kettle is lled passed the
minimum ll level (Min 1.0L) as indicated on the
water ll level.
If the kettle is overfilled, boiling water
may be ejected from the spout and
cause scalding.
• Lift the power switch to the ON position
(indicated by the symbol ‘I’).
WHEN THE WATER HAS BOILED
The kettle will automatically switch off
(indicated by the symbol ‘0’ ).
CLEANING THE KETTLE
The kettle exterior should be cleaned with a soft damp cloth. Do not use abrasive
cleaners or scouring pads which may damage the nish of the kettle.
Never immerse the kettle or the stand in water and always keep the electrical
contacts dry. Always disconnect from the mains before cleaning the stand.
DESCALING THE KETTLE
Depending on the hardness of the water
in your area, limescale may be deposited
on the heating element and the inside of
the kettle. This normal build-up is not
harmful to health but an excessive
amount of scale may affect the
performance of the kettle.
To descale, ll the kettle with distilled
water up to three-quarters of the Max
level and bring the water to boil. After the
kettle has switched off, add a descaling
solution following the manufacturers
instructions. Never attempt to descale the
kettle by chipping or scraping with a
sharp implement.
• Ensure that the switch is not obstructed and the lid is rmly closed.
The kettle will not turn off if the switch is obstructed or if the lid is
open.
• After removing the kettle, there may be some water on the surface of
the stand. This is condensation from the steam that causes the kettle
to automatically switch off after boiling. This is normal and should
not be a cause for alarm.
• The indicator in the power switch of the
kettle will light up blue to indicate that
the kettle is heating.
MAX
1.2L
1.0L
MIN
1.5L
1.8L
MAX
1.2L
1.0L
MIN
1.5L
1.8L
Power Connector Hole
Thank you for purchasing your new Logik Kettle.
Werecommend that you spend some time reading this instruction
manual in order to fully understand all the operational featuresit
offers.
Read all the safety instructions carefully beforeuse and keep this
instruction manual for future reference.
Stainless Steel Kettle
LC17PKB12
Brilliant Blue
LC17PKC12
Classic Cream
LC17PKR12
Ruby Red
C
M
Y
CM
MY
CY
CMY
K
LC17PKB_C_R12_IB_final120327_RC_min water level.pdf 2 10/04/2012 3:57 PM
