Loma Superscan Micro ISC Bedienungsanleitung
❍
❍
❍
❍
❍❍❍
CALIBRATE
CHANGE RESULTS
RUN DETECT
CALIBRATE
SYSTEM FAULT
RUN ERROR
▼▲
I S C
L o m a S u p e r s c a n M i c r o
❍SETUP
ENTERCANCEL
1
MENUS A to Z
Description:
The batch length is specified in hours, or optionally in the number of packs if a PEC is fitted. The
batch length represents the amount of production statistics that will be accumulated, before they are
transmitted down the serial link to a printer or computer, and then reset to zero.
Press the [ENTER] key, and then the [▲] and [▼] keys to adjust the batch length as necessary.
Scope:
00.00 to 24.00 for timed batch interval
0 to 9999 for pack batch interval
Default:
01.00 for time.
Notes:
Batch reports must be enabled in the Report Options menu for this menu entry to appear.
*BTCH LENTH 1.00
●
●
BATCH LENGTH
❍
❍
❍
❍
❍❍❍
CALIBRATE
CHANGE RESULTS
RUN DETECT
CALIBRATE
SYSTEM FAULT
RUN ERROR
▼▲
I S C
L o m a S u p e r s c a n M i c r o
❍SETUP
ENTER
CANCEL
2
MENUS A to Z
Description:
This facility can be used to synchronise the start of the batch to a particular time of day. For example,
if hourly batch statistics are required starting from 6.30pm, then the Batch Length would be set to
1.00 hour and the Batch Start to 18.30 hours. This would mean that the batch statistics would be reset
and transmitted down the serial link every hour at half past the hour.
Press the [ENTER] key, and then the [▲] or [▼] keys to adjust the batch start time.
To turn the start time facility off, so that batch statistics are reset and transmitted at multiples of batch
lengths after the batch starts, set the start time to 00.00.
Scope:
00.00 to 24.00. 00.00 will disable this facility.
Default:
00.00
Note:
This menu entry will only appear when Batch Reports are enabled, and the batch units are in terms of
time.
*BTCH START 1.30
●
●
BATCH START
❍
❍
❍
❍
❍❍❍
CALIBRATE
CHANGE RESULTS
RUN DETECT
CALIBRATE
SYSTEM FAULT
RUN ERROR
▼▲
I S C
L o m a S u p e r s c a n M i c r o
❍SETUP
ENTERCANCEL
3
MENUS A to Z
*BTCH UNITS PACKS
Description:
Press the [ENTER] key, and then the [▲] or [▼] key to select between time or packs for the batch
interval.
Scope:
TIME or PACK.
Default:
TIME.
Notes:
A photo eye (PEC) must be fitted if the batch interval is to be set in terms of the number of packs.
This menu entry will only appear when batch reports are enabled in the Report Option menu.
●
●
BATCH UNITS
❍
❍
❍
❍
❍❍❍
CALIBRATE
CHANGE RESULTS
RUN DETECT
CALIBRATE
SYSTEM FAULT
RUN ERROR
▼▲
I S C
L o m a S u p e r s c a n M i c r o
❍SETUP
ENTER
CANCEL
4
MENUS A to Z
Description:
The date and time specified within this menu are used to time stamp the data in the contaminant, fault
and error logs, and also on the printed reports.
Press the [ENTER] key to gain access to the Calendar menu to setup the date and time.
Note:
The time of day is specified using the 24 hour clock.
CALENDAR
●
●
CALENDAR
❍
❍
❍
❍
❍❍❍
CALIBRATE
CHANGE RESULTS
RUN DETECT
CALIBRATE
SYSTEM FAULT
RUN ERROR
▼▲
I S C
L o m a S u p e r s c a n M i c r o
❍SETUP
ENTERCANCEL
5
MENUS A to Z
Description:
Press the [CALIBRATE] key to move into the calibrate menu from any other menu position, from
where Full Calibration, Update Calibration or Man Setup can be accessed.
Note:
A calibration report will be transmitted down the serial link upon completion of a calibration cycle,
only if report is enabled in the serial link menu, and the calibration report is enabled in the Report
Options menu.
ANY DISPLAY
●
●
SAMPLE REPORT
---------------------------------------
: LOMA SUPERSCAN MICRO METAL DETECTOR :
---------------------------------------
CALIBRATION REPORT
Time : 15-32-16 Date : WED 20 SEP 1995
Product Number : 1
Product Identification : CHEESE
Machine Identification : MD12345
Working Mode : REACT
Working Mode Lock : YES
Minimum Threshold : 500
Maximum Threshold : 15000
Detection Threshold : 885
Product Compensation : -448
Head Power : MAX
Head Lock : NO
---------------------------------------
CALIBRATE
❍
❍
❍
❍
❍❍❍
CALIBRATE
CHANGE RESULTS
RUN DETECT
CALIBRATE
SYSTEM FAULT
RUN ERROR
▼▲
I S C
L o m a S u p e r s c a n M i c r o
❍SETUP
ENTER
CANCEL
6
MENUS A to Z
Description:
In order to change the running product press the [CHANGE] key, then use the [▲] or [▼] to make
your selection. Finally, press the [ENTER] key for the selection to take effect.
Warning Messages:
+CHANGING TO+ This message is always displayed to indicate that a product change is
taking place. The new product name and number is displayed on the
next display.
+NOT CALIBRATED+ This message indicates that the selected product has never been
calibrated. To rectify this position go to the Product Setup menu and
make sure that the entries are correct before performing a full calibrate.
ANY DISPLAY
●
●
CHANGE PRODUCT
❍
❍
❍
❍
❍❍❍
CALIBRATE
CHANGE RESULTS
RUN DETECT
CALIBRATE
SYSTEM FAULT
RUN ERROR
▼▲
I S C
L o m a S u p e r s c a n M i c r o
❍SETUP
ENTERCANCEL
7
MENUS A to Z
Description:
Press the [ENTER] key to clear the entries in the contaminant log.
CLEAR CONTAMS?
●
●
CLEAR CONTAMINANTS LOG
❍
❍
❍
❍
❍❍❍
CALIBRATE
CHANGE RESULTS
RUN DETECT
CALIBRATE
SYSTEM FAULT
RUN ERROR
▼▲
I S C
L o m a S u p e r s c a n M i c r o
❍SETUP
ENTER
CANCEL
8
MENUS A to Z
CLEAR ERRORS?
Description:
Clearing a run error will turn the run error LED and Auxiliary relay off if it is configured for run error
indication, providing the error is no longer occurring. If the error is active, ie. still occurring, then the
run error will immediately come back putting the LED on.
Press the [ENTER] key to clear any run errors.
Notes:
Refer to the section on Error/Fault Logging for full details about run errors.
●
●
●
CLEAR ERRORS
❍
❍
❍
❍
❍❍❍
CALIBRATE
CHANGE RESULTS
RUN DETECT
CALIBRATE
SYSTEM FAULT
RUN ERROR
▼▲
I S C
L o m a S u p e r s c a n M i c r o
❍SETUP
ENTERCANCEL
9
MENUS A to Z
Description:
Clearing a system fault will turn the system fault LED and Fault relay off, providing the fault is no
longer occurring. If the fault is active, ie. still happening, then the system fault will immediately come
back putting the fault LED and relay back on.
System faults are usually an indication of a serious malfunction with the equipment, and must
therefore be investigated promptly. Refer to the section on Error/Fault Logging for full details about
system faults, and what to do if you have one on your system.
Press the [ENTER] key to clear any system faults.
Notes:
On failsafe systems, the fault relay is typically wired into the conveyor or reject so that no product
can pass down the line in the event of a system fault.
Clearing the faults as described here will reset the LED fault indicator and the internal fault relay, but
the details in the fault log will not be cleared. These are maintained by the system for Loma Customer
Service Engineer reference.
CLEAR FAULTS?
●
●
●
CLEAR FAULTS
❍
❍
❍
❍
❍❍❍
CALIBRATE
CHANGE RESULTS
RUN DETECT
CALIBRATE
SYSTEM FAULT
RUN ERROR
▼▲
I S C
L o m a S u p e r s c a n M i c r o
❍SETUP
ENTER
CANCEL
10
MENUS A to Z
Description:
This value is automatically derived during a calibration cycle, and should therefore not normally
require adjustment: only alter the value if advised to do so by a LOMA Service Engineer.
Press the [ENTER] key to view the compensation and signal level values; the [▲] and [▼] keys to
adjust the compensation value. The compensation value is displayed on the left hand side of the
display, and the signal level on the right hand side.
Scope:
-65535 to 65535
Notes:
This menu position is only accessible if the Manual Setup menu has been enabled in the User Options
menu.
The calibrate LED will illuminate whilst the compensation value is being adjusted.
For more information about what the compensation value does, please refer to the Principles of
Operation section.
COMPENSATION
●
●
COMPENSATION
Andere Handbücher für Superscan Micro ISC
1
Inhaltsverzeichnis
Andere Loma Metalldetektor Handbücher
Loma
Loma X5c Bedienungsanleitung
Loma
Loma IQ3X Bedienungsanleitung
Loma
Loma IQ3+ Bedienungsanleitung
Loma
Loma IQ2 Bedienungsanleitung
Loma
Loma IQ2 Bedienungsanleitung
Loma
Loma Superscan Micro Handbuch
Loma
Loma Superscan Micro ISC Bedienungsanleitung
Loma
Loma IQ3+ST Bedienungsanleitung
Loma
Loma IQ + Betriebsanleitung
Loma
Loma IQ3 Bedienungsanleitung
Beliebte Metalldetektor Handbücher anderer Marken
Steinberg Systems
Steinberg Systems SBS-MD-22 Bedienungsanleitung
Zircon
Zircon MetalliScanner m60c Bedienungsanleitung
nalanda
nalanda MD027 Bedienungsanleitung
REV Ritter
REV Ritter CB-7005 Bedienungsanleitung
Minelab
Minelab F1A4 Bedienungsanleitung
Fisher Research Labs
Fisher Research Labs F70 Bedienungsanleitung
Steinberg Systems
Steinberg Systems SBS-MD-12 Bedienungsanleitung
GOLDEN MASK
GOLDEN MASK 5 Bedienungsanleitung
Grizzly
Grizzly YM 203 Bedienungsanleitung
Fisher Research Labs
Fisher Research Labs 1280-X Aquanaut Bedienungsanleitung
Treasure Cove
Treasure Cove Vibra-Probe 560 Bedienungsanleitung
Accurate Locators
Accurate Locators XL16 IMAGER Bedienungsanleitung