Longevity 6634QDS Bedienungsanleitung

Congratulations on purchasing a Longevity Acrylics bathware

product. Be assured that your product has been developed and is

a highly engineered, quality product that is strong and durable to

withstand the rigors of everyday life.

• Strength, durability and toughness to withstand frequent use

•Resistant to everyday wear and tear, stains, and superﬁcial scratches

• Resistant to UV, and many household chemicals

• Qualities that make light work of cleaning and maintenance

• Beautiful warm, smooth surfaces that feel comfortable against the

skin

INSPECTION: THIS ACRYLIC UNIT HAS BEEN CAREFULLY

INSPECTED AND PACKED FOR SHIPMENT AT LONGEVITY

ACRYLICS INC. PLEASE FULLY INSPECT THE UNIT BEFORE

INSTALLATION.

Carefully remove the unit from the carton. Do not destroy the

cardboard until you have inspected the unit thoroughly. Should your

inspection reveal any damage or defect in the ﬁnish, do not install the

unit—contact your distributor immediately.

The warranty does not cover damages or defects to the ﬁnish claimed

after the unit has been installed. Longevity’s responsibility for shipping

damages ceases upon delivery of the product in good order to the

carrier.

Refer any claims for damages to the carrier.

FREESTANDING BATHTUBS

(6636 QDS / 6634QDS)

INSTALLATION INSTRUCTIONS

BUILDING CODES

Be sure to follow local building codes when installing the bathware

unit.

IT IS ALWAYS RECOMMENDED TO HAVE A PROFESSIONAL

AND COMPETENT PLUMBER INSTALL LONGEVITY ACRYLICS

BATHWARE.

CAUTION

• To cut plumbing ﬁxture openings on your bathware unit ensure

that you use the correct size hole saw based on the selected unit

design.

• Always cut a plumbing ﬁxture opening from the ﬁnished side of

the unit.

• Always ensure that the surface of the unit is protected to prevent

scratches in the surface.

• Install plumbing ﬁxtures based on the manufacturers

recommended installation instructions.

• The drain location on the unit is shown; however actual

installation will depend on the waste and overﬂow which is

purchased separately.

LONGEVITY ACRYLICS INC. IS NOT RESPONSIBLE FOR ANY

DAMAGES INCURRED AS A RESULT OF POOR INSTALLATION

OF THE PRODUCT.

REQUIRED TOOLS

Screwdriver Pencil Silicone Sealant Gun

Electric DrillLevel Square

Safety Equipment:

Gloves, Boots and Glasses

Every effort has been made to offer the most current, correct, and clearly expressed information possible. Nevertheless, inadvertent errors or inaccuracies in the information may occur.

Longevity Acrylics disclaims any responsibility for errors or accuracy of information that may be contained in its documents or web pages. Longevity Acrylics Inc. makes no warranties or

representations whatsoever regarding the quality, content, completeness, suitability, adequacy, sequence, accuracy or timeliness of such information and data.

INSTALLATION

GENERAL INSTALLATION NOTES

IMPORTANT: READ ALL INSTRUCTIONS CAREFULLY

BEFORE PROCEEDING. STRUCTURE MEASUREMENTS

MUST BE VERIFIED AGAINST THE UNIT. ENSURE THE

STRUCTURE MEETS THE REQUIRED DIMENSIONS, IT IS

LEVEL AND SQUARE.

Check that ﬂoor is level, adjust as necessary. Shimming may be

required to level the bathware unit to ensure adequate drainage.

Levelling must be done under the wood base beneath the unit.

Do not level directly behind or under the ﬂange and/ or at the

front of the unit.

ALWAYS ENSURE THAT THE SURFACE OF THE UNIT IS

PROTECTED TO PREVENT SCRATCHES IN THE SURFACE.

INSTALLATION STEPS

1. Unpack the bathtub and be very careful during installation

so as to not damage the acrylic surface of the tub.

2. Position the tub in the area where it will be installed. Mark

the centre of the drainage line in relation with the desired

position of the bathtub. (

Figure 1

)

3. Carefully remove the tub interior from the apron of the tub

by lifting the tub interior from its fastening/alignment pins.

(

Figure 2

)

4. Align the centre of the drainage line with the sub-ﬂoor

Cutout Template. Cut a 6-1/2" (16.5 cm) hole into wood

sub-ﬂoor (use supplied Cutout Template).

5. Measure and cut ABS Tailpiece as necessary to ensure a

secure connection to P-Trap below.

6. Insert Drain assembly into ﬂoor opening and connect to

pipe below.

7. Afﬁx to sub-ﬂoor with 6 screws (not supplied)

8. Install ﬂooring surface, leaving a 6-1/2" opening to access

Drain.

Every effort has been made to offer the most current, correct, and clearly expressed information possible. Nevertheless, inadvertent errors or inaccuracies in the information may occur.

Longevity Acrylics disclaims any responsibility for errors or accuracy of information that may be contained in its documents or web pages. Longevity Acrylics Inc. makes no warranties or

representations whatsoever regarding the quality, content, completeness, suitability, adequacy, sequence, accuracy or timeliness of such information and data.

centre of

drain location

FIGURE 1

mounting brackets

alignment pins

FIGURE 2

Carefully lower the tub with the installed brass tailpiece into the

red collar in drain assembly. Ensure tailpiece is fully engaged

with the seal.

9. Adjust the position of the apron so that the alignment pins

can be securely fastened to the mounting brackets.

10. Fasten the tub apron by pre-drilling four holes as indicated

using a 3/8" drill bit. Apply a bead of silicone under the

deck (optional). (

Figure 3

)

11. Afﬁx the appropriate Tailpiece to the Waste & Overﬂow.

NOTE: DO NOT CUT THE BRASS TAILPIECE AS THIS

MAY CAUSE A LEAK. Ensure the measurement between

the base of the Drain and P-Trap will accommodate the

Tailpiece.

12. Cut out the Installation Label with a utility knife and

remove to expose the Drain.

13. Apply lubricant (supplied) to the tailpiece.

14. Carefully position the tub and brass tailpiece in-line with

the drain, and lower the tub back onto the fastening/

alignment pins (ENSURE THAT THE FASTENING/

ALIGNMENT PINS ARE SECURE INSIDE THE

MOUNTING BRACKETS). (

Figure 4

)

Every effort has been made to offer the most current, correct, and clearly expressed information possible. Nevertheless, inadvertent errors or inaccuracies in the information may occur.

Longevity Acrylics disclaims any responsibility for errors or accuracy of information that may be contained in its documents or web pages. Longevity Acrylics Inc. makes no warranties or

representations whatsoever regarding the quality, content, completeness, suitability, adequacy, sequence, accuracy or timeliness of such information and data.

cutting template

FIGURE 3

FIGURE 4

TABLE 1 - TECHNICAL DATA

Every effort has been made to offer the most current, correct, and clearly expressed information possible. Nevertheless, inadvertent errors or inaccuracies in the information may occur.

Longevity Acrylics disclaims any responsibility for errors or accuracy of information that may be contained in its documents or web pages. Longevity Acrylics Inc. makes no warranties or

representations whatsoever regarding the quality, content, completeness, suitability, adequacy, sequence, accuracy or timeliness of such information and data.

Model#

Wide

Long

High

Floor

Dimension

DrainBack

DrainEnd

6636 36" 66" 24½" 45"x22" CENTERDRAIN 33" 18"

663434"67" 24½" 47½"x20" 17"12"

CLEANING

For normal care and cleaning use a soft cloth using our

Longevity Acrylics Acrylic Bathtub & Shower Clean & Shine:

• It will gently clean all acrylic surfaces without scratching

• Leaves a lustrous shine that resists fogging, repels dust, and

eliminates static

• Resist ﬁnger marking

• Contains no abrasive or harsh chemicals

• Leaves a clean smooth, greaseless shine

If using a household cleaner, make sure it is recommended for

use on acrylic by the manufacturer. Be sure to read the label

and follow the cleanser’s recommendations. Never use abrasive

cleaners.

Do not allow your Longevity bathware surface to come

into contact with products such as ketones or esters such as

acetone or ethyl acetate (nail polish remover), Wintergreen

oil (methyl salicylate), nail polish, dry cleaning solution or

other chlorinated organic solvents, lacquer thinners, gasoline,

aromatic solvents, pine oil, etc.

Remove dust and dry dirt with a soft, damp cloth. Clean grease,

oil, paint and ink stains with isopropyl (rubbing) alcohol. Dry

with a clean, soft cloth.

Avoid using razor blades or other sharp instruments that might

scratch the surface. Small scratches can be removed by applying

a thin coat of automotive paste wax and buff lightly with a clean

cloth.

If you use a rubber or plastic anti-skid mat, make sure to remove

it after every shower to avoid harming the surface ﬁnish.

Dieses Handbuch passt für folgende Modelle

Andere Longevity Badewanne Handbücher

Longevity

Longevity 7236 Bedienungsanleitung

Beliebte Badewanne Handbücher anderer Marken

Agua

Agua BARTOLI-66 Bedienungsanleitung

PAA

PAA PRELUDE Bedienungsanleitung

BETTE

BETTE SILHOUETTE Bedienungsanleitung

Kohler

Kohler K-820-GC Kurzanleitung

American Standard

American Standard Whirlpool/Bathing Pool 2748.XXXW Bedienungsanleitung

Oliveri

Oliveri Naples Bedienungsanleitung

Lyons

Lyons Elite ETLxx663219 Series Bedienungsanleitung

Woodbridge

Woodbridge BJ500 Montageanleitung

Whirlpool

Whirlpool Ariel ARL-702 Bedienungsanleitung

TEIKO

TEIKO EXCELLENT DUO Bedienungsanleitung

American Standard

American Standard Colony 5-1/2' x 32" Bedienungsanleitung

American Standard

American Standard 3052OD.X0X Kurzanleitung

Kohler

Kohler K-1111-H2 Kurzanleitung

agape

agape MARSIGLIA AVAS1075 Bedienungsanleitung

Kohler

Kohler K-1151 Montageanleitung

Kohler

Kohler K-1158 Kurzanleitung

Kohler

Kohler K-1244 Montageanleitung

Kallista

Kallista P50045-G5 Montageanleitung