Longshine LCS-C844 Bedienungsanleitung
Longshine Technologie Europe GmbH
LCS-C844
Device Server
www.longshine.de
RS-232/422/485 to
10/100Base-TX
Device Server
User’s Manual
COPYRIGHT
All rights reserved. No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in any form or by any
means, whether electronic, mechanical, photo copying, recording or
otherwise, without the prior written permission of the publisher.
FCC WARNING
This equipment has been tested and found to comply
with the limits for class A device, pursuant to part 15 of FCC rules.
These limits are designed to provide reasonable protection against
harmful interference in a commercial installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communication. Operation of this
equipment in a residential area is likely to cause harmful
interference, in which case, the user will be required to correct the
interference at the user’s own expense.
CE
This is a Class A product. In a domestic environment, this product
may cause radio interference in which case the user may be
required to take adequate measures.
Take special note to read and understand all content given in the
warning boxes
Warning
Table of Contents
1 Introduction.............................................................1
About This Guide..................................................1
Features................................................................2
Specifications........................................................3
Package Contents ................................................5
2 Hardware Description.............................................6
Product Overview..................................................6
Product Illustrations ..............................................7
3 Installation...............................................................8
Location ................................................................9
Wall Mount Installation........................................10
Din Rail Mount Installation..................................10
Powering On Unit................................................12
Connecting Copper Cable ..................................13
DB9 Male Connector Pin Assignments ..............14
Serial Connection ...............................................15
Definition of DIP Switches ..................................15
4 LED Indicators.......................................................17
5 Configuration.........................................................18
Console Port Access ..........................................18
Telnet Access .....................................................21
Web Access........................................................22
6 Management..........................................................24
Via Menu-Driven (Console Port & Telnet)..........24
System Information Menu...................................25
DHCP Configuration Menu.................................26
RS-232/422/485 Transfer Configuration.............26
Monitor Menu......................................................29
TFTP Firmware Upgrade Menu..........................30
SNMP Configuration Menu.................................31
System Restart Menu.........................................33
Command Line Interface ....................................35
Command Definitions .........................................35
Web Browser Interface.......................................37
Appendix A...............................................................46
Serial IP Redirector.............................................46
1
1 Introduction
About This Guide
Welcome
Thank you for selecting the RS-232/422/485 to
10/100Base-TX Device Server. This unit is designed
to provide a RS-232/422/485 connection over twisted-
pair cable where the connected devices have RS-
232/422/485 interfaces. Enabling serial devices such
as CNCs and PLCs to instantly connect to an existing
Ethernet/ Fast Ethernet network, the Serial-to-
Ethernet Device Server represents a robust solution
for devices controllers for MIS personnel.
Purpose
This guide discusses how to install and configure your
RS-232/422/485 to 10/100Base-TX Device Server.
Terms/Usage
In this guide, the term “Device Server” (first letter
upper case) refers to your RS-232/422/485 to
10/100Base-TX Device Server, and “device server”
(first letter lower case) refers to other device servers.
2
Features
•Complies with EIA/TIA and IEEE standards
•Supports 4 wires full duplex asynchronous serial
data transmission (RS-422/485)
•Supports 2 wires half-duplex asynchronous serial
data transmission (RS-485)
•Supports serial port asynchronous data rates up
to 115.2 Kbps
•Extended distances up to 1.2 km (24 AWG) using
RS-422/485
•Auto-detecting 10/100 Mbps Ethernet interface
•Terminator feature improves signal quality and
distance
•LEDs for ‘at-a-glance’ device status
•Wall mount or Din-Rail mountable installation
•Power range 9~32V DC
•FCC Class A & CE approved
3
Specifications
Standards: IEEE 802.3 (10BASE-T Ethernet);
IEEE 802.3u (100BASE-TX/ Fast
Ethernet); EIA/TIA RS-232/422/485;
EIA/TIA-574
Ports: 1x UTP 100/120ohm; RJ-45 type
1x 9-pin serial connector; D-sub, Male
Max. Distance: UTP: 100 meters (Cat 3/4/5.)
Serial: 15 meters (RS-232)
1,200 meters (RS-422, RS-485)
Data Rates: UTP: 10 or 100 Mbps
Serial: 115.2 kbps (asynchronous)
Signals: RS-232: TxD, RxD, CTS, RTS, DTR,
DSR, RI, DCD, GND RS-422: TxD+/-,
RxD+/-, GND RS-485: Data+, Data-,
GND
Configuration: Bits Per Second: 38400
Parity: None
Data bits: 8
Stop bits: 1
Flow Control: None
(The console connection is only available once the
DIP switch 1 is ON)
4
Switches:
DIP 1: Enables / disables console / data
communication mode
DIP 2: Enables / disables RS-232
DIP 3: Enables / disables RS- 422/485
(4-wire)
DIP 4: Enables / disables RS-485 (2-wire)
DIP 5: N/A
DIP 5: N/A
DIP 7: Enables / disables termination (TMR)
Power: External power adapter; 9~32V DC @
800mA
Frequency: 47Hz to 63Hz
Environment:
Temperature:
Operating: 0°C to 50°C
Relative Humidity:
10% to 80%, non-condensing
Storage:
-20°C to 80°C
Relative Humidity:
5% to 90%, non-condensing
Emissions: FCC Part 15 of Class A & CE approved
Dimensions: 109.2 x 90 x 30mm (L x W x H)
Weight: 280 grams
5
Package Contents
The package should include the following:
•One RS-232/422/485 to 10/100 Base-TX Device
Server unit
•One power adapter (please check connector type
and input power specification)
•Four self-adhesive pads
•DIN Rail Kit
•Screws for wall-mount installation
•User’s Manual CD
•Serial IP Redirector software CD
Inhaltsverzeichnis
Andere Longshine Server Handbücher
Beliebte Server Handbücher anderer Marken
iRobo
iRobo IPC2U Bedienungsanleitung
Nortel
Nortel 1000 Con?guration guide Bedienungsanleitung
Asus
Asus AP7500 Bedienungs- und Wartungshandbuch
Avid Technology
Avid Technology AirSpeed 5000 Bedienungsanleitung
HP
HP Integrity rx2600 Installationsanleitung
Milestone
Milestone Husky IVO 350T Bedienungsanleitung