LooLinn Z6Pro Bedienungsanleitung
User Manual
Camera with 500 m
Image
transmission range
(Please ensure your mobile
phone supports with 5G WiFi )
Accreditation standard: GB/T26701-2011
14+
Z
6Pro
GPS BRUSHLESS DRONE
Palm control
Flight plan Waypoint flightGPS tracking One key to retrun Circle flight
Human tracking
5G WIFI
Camera
Optical flow
positioning Long battery life Dual-frequency
technology
Take-off/landing
R
Important safety information
Thank you for purchasing this Loolinn product. To ensure that you operate the
drone correctly, please read these instructions carefully before first use and store
them in a safe place for future reference.
-1-
1. Adult or experienced RC pilot’s supervision is recommend for children.
2. Rechargeable batteries are only to be charged under adult supervision.
3. Turn off the drone/transmitter and remove the batteries when not in use.
4. The supply terminals are not be short-circuited.
5. Keep away from the rotating blades (rotating blades may cause bodily injuries,
or damage to property).
6. Attention：please assemble the drone with the guidance of adults.
7. Do not look directly into the LED lights of the drone as make your eyes
uncomfortable.
8. Exhausted batteries are to be removed from the drone.
9. Please store the smaller-sized drone accessories in places that are out of
reach of children.
10. This drone is very powerful. For all first-time flights, the left joystick must be
slowly pushed up in order to prevent the drone from ascending too fast to
avoid unnecessary collision and possible damage and injury.
11. When the flight is ended, first turn off the power of the remote control. Then turn
off the power of the drone.
12. Avoid placing the batteries in places with high temperatures and exposure to
heat.
13. Please keep a safe distance from the spinning propellers to avoid injury.
14. To ensure the electromagnetic environment requirement of the aviation radio
(station), using remote controls in the zone, which is in a radius of about 5000m
zone from the circle center of the airport runway, is forbidden.All users also
should abide by the regulation of the radio set forth by government and
regulatory agencies including the duration and area.
15. Pay attention to keeping distance of 2-3 meters from the user or other people
when the drone is flying, avoid the drone landin to hit the head, face or face or
body of anoter person.
16. The packing has to be kept since it contains important information.
Safety Guide
Repair and maintenance
1. Use clean and soft cloth to clean the product.
2. Keep away the product from heat sources.
3. Avoid water exposure to this product. Moisture may cause damages of the
drone electronic parts.
4.Transformers used with the drone should be examined regularly,such as the
cord,plug,enclosure and other parts,If any damages are found, please
stop using it unless it is repaired or replaced.
Specifications
-2-
About this product
Download and install the Loolinn Air App
Drone weight
Drone Size
Range
Altitude
Image transmission range
Flight time
Operating conditions
Video transmission frequency
Motor
Battery
Charging time
216 g
305x280x65 mm
500 m
100 m
500 m
Hovers indoors for 24-25 minutes
0°C to 40°C
5 GHz
1503 Brushless motor
7.6 V 1700 mAh
About 3 hours
· Drone
Operating frequency
Range
Operating conditions
Charging time
2.4 GHz
500 m
0°C to 40°C
About 1 hours
· Remote control
Drone
Remote control
USB charging cable
Clockwise/anticlockwise propellers
Instructions
For Android phones, download and install the Loolinn Air
App by visiting Google Play or by scanning the QR
code.
For IOS Apple phones, download and install the Loolinn
Air App by visiting the App Store or by scanning the QR
code.
* Note: For best results, use a device with iOS 8.0/Android 5.0 or later.
1
1
2
4
1
· Package contents
-3-
①
①Photo button
②Record button
③Left joystick
④On / Off button
⑤One Key Take Off / Landing
⑥Calibrating the compass
⑦Home button
⑧Phone holder
⑨Lens up
⑩Lens down
Right joystick
②
③
④ ⑤
⑩
⑥
⑨
⑧
⑦
Remote control
①Motor
②Propeller blades
③Power switch
④Front camera
Drone components
⑤Battery
⑥Front LED indicator
⑦Rear LED indicator
⑧Bottom camera
⑥
⑤
⑦
⑧
①
②
③
④
-4-
!
Assembling the product
Installing the propellers
Clockwise propellers Anticlockwise propellers
Inserting a memory card (optional accessory)
* Attach the propellers as shown in the diagrams above. Ensure that they are
attached in the correct orientation.
* Ensure that the clockwise and anticlockwise propellers are attached to the
correct arms. The drone will not fly correctly if the propellers are attached
in the wrong position.
* The propellers are made from a delicate material. Pay attention when
attaching them to the drone.
* Only use propellers that are supplied by the manufacturer.
* The propellers are consumable parts. If necessary, purchase replacements
from the manufacturer.
1
2
3
1
2
3
5V2AA adapter
USB
!
* Charge the drone with the USB charging cable that came with the product.
* The battery will take longer to charge when you use an adapter with a smaller
rated current.
1 2 3
-5-
Remove the battery
Charge the battery
Charging the drone battery
USB charging cableBattery
Indicator in slow flashing green:
Charging in progress
Indicator in constant green:
Battery is fully charged
Indicator in rapid flashing green:
Battery is defective
Insert the battery
* Ensure that the battery holder
clicks into place.
* Do not short circuit or compress the battery, as this may cause an
explosion.
* Do not disassembling the battery or store it in a hot environment.
* If you do not plan to use the drone for at least 10 days, discharge the
battery to 40%-50%. This helps to prolong the lifespan of the battery.
* Rechargeable batteries should be removed from the drone before
being charged.
* Rechargeable batteries should only be charged under the supervision
of adults.and keep away from flammable materials.
* Exhausted batteries should be removed from the drone.
* Caution: Risk of explosion if battery is replaced with incorrect ones,
please install the batteries according to the instructions.
1
2
-6-
5V 1-2A
3
41
111 1
222 2
Open the remote control
Close the remote control
Flight preparation and turning the drone on/off
Pairing the remote control with the drone
Charging the remote
control batteries
Attaching the phone holder
Indicator stays constant when
pairing is complete.
* When you switch on the remote control, the indicator will flash
rapidly for approximately 20 secs to indicate that the remote
control is waiting for a signal. The indicator will then flash slowly to
indicate that pairing mode has been disabled.
!
Remote control
indicator flashes
rapidly
Switch on the remote control Indicator flashes
rapidly -> slowly
Switch off the remote controller
during charging
Charging : red light is on
Finish charging: light is off
2
-7-
1
Searching for satellites
The rear indicator will change from orange to green when the drone has locked
on to a satellite and recorded the take-off location. The drone is now ready to fly.
Calibrating the compass
* Do not calibrate the compass near strong electromagnetic fields or
large pieces of metal, e.g. magnetite, car parks or buildings with
underground steel reinforcements.
* When holding the drone horizontally, the angle of inclination must
not exceed 30 degrees.
!
!
* It should take approximately one minute for the drone to lock on to a
satellite. If the drone fails to find a satellite, recalibrate the compass.
* Before take-off, place the drone in an open space away from
obstacles and ensure that GPS mode is enabled.
* When the rear green indicator flashes rapidly, this indicates that the
GPS signal is weak. If this occurs, land the drone manually and
restart the satellite search.
Turning the drone on
Push the left and right joysticks
downwards in a V shape for 1
second.
Move the left joystick
upwards
or
Press to calibrating the
compass Hold the drone horizontally
and rotate 360 degrees for
few time. Indicator flashes
from slowly to rapidly.
Hold the drone vertically
and rotate 360 degrees for
few times. Indicator flashes
from rapidly to constant.
2
3
-8-
!
Turning the drone off
Method one Method two Method three
* The drone will switch off automatically if its angle of inclination
exceeds 90 degrees.
Using the remote control
Ascend
Descend
Forward
Backward
Left Rotation
Leftward Rightward
Right Rotation
Front
Rear
Front
Rear
Push the left joystick
downwards for 2-3
seconds.
Push the left and right
joysticks downwards in
a V shape for 2
seconds.
Press the take-off/land-
ing button to make the
drone land
automatically and
switch off.
-9-
!
!
Headless mode
The indicator on the drone will flash once every 4 seconds.
* When the battery level is normal, the drone can fly to a distance of
500 m at a maximum altitude of 100 m.
* When the battery level is low, the drone can fly to a distance of 20 m
at a maximum altitude of 20 m.
* If the rear indicator starts to flash rapidly, this indicates that the GPS
signal is weak and the drone cannot determine its position.
* GPS mode cannot be used indoors.
1. Configuring the forwards direction
When you switch on the drone for the first time, the direction in which the
front side of the drone is pointing will be set as the forwards direction.
2. Enabling headless mode
①After pairing the remote control with the drone, hold down
the right joystick for approximately 3 seconds. The remote
control will beep 8 times to indicate that headless mode is
enabled. To disable headless mode, hold down the right
joystick again for approximately 3 seconds.
②In headless mode, you do not need to determine the
drone’s orientation. You can move the joysticks on the
remote control to make the drone move in the corresponding
direction.
* If the rear indicator starts to flash rapidly, this indicates that the optical
signal is weak and the drone cannot determine its position.
* Performance may be impaired in dark surroundings, areas with
reflective surfaces (e.g. water), or at altitudes of more than 6 m.
* Optical flow positioning only supports altitudes of less than 6 m.
Flight modes
Optical flow positioning
Front indicator is constant white, rear indicator is constant
yellow.
GPS mode
Front indicator is constant white, rear indicator is constant
green.
Inhaltsverzeichnis
