Lorex WA-410 Bedienungsanleitung

FREQUENTLY ASKED QUESTIONS FOR WIRELESS SECURITY SYSTEM WA410/ SY4100

1) Q: This WA410/ SY4100 system compatible with WA400/ SY4000 system?

A: No, this is due to the different communication method use between the main console and

peripheral units with WA410/ SY4100 System and WA400/ SY4100 System so there is no

compatibility between these systems including the peripheral units.

2) Q: Can this system be monitor by the security monitoring company?

A: No, this system is stand alone type and there is no capability to communicate with the security

monitoring company.

3) Q: Can the emergency, police/ fire department telephone number be programmed in to

the system?

A: Please check the local authorities that to ensure “Auto Dialer” security features are permissible

with that particular local area and that the telephone numbers which you will program are correct.

4) Q: What is “Away/ Home” arm mode?

A: Away arm mode: When the system is armed in this mode, all sensors are active and the any

of sensor is triggered, the system will activate the alarm as well as the auto dialer function.

Home arm mode: When the system is armed in this mode, all PIR sensor zones are excluded

from the system and the activation of these sensor will not activate the alarm neither the auto

dialer function.

5) Q: What is “Instant/ Delay/ Home Bypass/ 24 Hr zone?

A: Instant Zone: This zone is belong to the “Window Sensor” and if the system is in arm mode,

the alarm/ auto dialer function will activate immediately when the sensor belong to this zone is

triggered.

Delay Zone: This zone is belong to “Door/ PIR Motion Sensor” and if the system is in arm mode,

the alarm/ auto dialer function will activate after the entry delay period when the sensor belong to

this zone is triggered.

Home Bypass Zone: This zone is belong to “PIR Motion Sensor” and if the system is in “Home

Arm Mode”, the alarm/ auto dialer function will not activate when the sensor belong to this zone is

triggered and the sensor belong to this zone will be excluded from the system.

24Hr Zone: This zone is belong to “Smoke Detector/ Gas Detector/ Panic Watch and Remote

Control Panic Button” and if the system is in arm/ disarm mode, the alarm/ auto dialer function will

activate immediately when the sensor belong to this zone is triggered.

6) Q: Can the alarm/ exit delay/ entry delay duration be changed?

A: Yes, these durations are programmable via the setup menu and can be set individually for

duration of 1~255 Sec.

7) Q: I forget the “Password”, how to find out “Password” or what to do?

A: Please disconnect all power to the main console (i.e. AC adaptor/ Backup Battery), the main

console will reset the password to manufacturer default setting so then reprogram the password

using the default password. The default passwords are as follows;

Installer Password “1, 2, 3, 4, 5, 6”

Master Password “1, 3, 5, 2, 4, 6”

8) Q: When the power failure occurred without backup battery in place, what will happen with

programmed setting in the main console?

A: The following programmed setting will be initialized;

The setting of “Exit/ Entry/ Alarm Duration, Dial Set and Installer/ Master Password”.

However the following programmed setting will be remain intact;

The setting of “Preset Telephone Numbers, Recorded Voice Message and Programmed

Peripheral Units”.

9) Q: How long the backup battery last?

A: In term of life span of backup battery, the backup battery will last for about 5 years.

In terms of operation time without AC power, this backup battery will support the system for about

8 hours in standby mode without AC power.

10) Q: The system includes the main console/ peripheral unit can be placed in unheated

area or outside?

A: The system is made for indoor use only so it cannot be placed outdoor. The operating

temperature range of this system is 0~40 degree C so the system will work properly if the system

is placed in area where does not exceed the specification of operating temperature range.

11) Q: How many voice massages can be programmed with this system for different

occasion?

A: Unfortunately this system can support only one voice massage for length of 25 Sec maximum.

So the content of message must be general.

12) Q: The system produces 2 short trip every 10 Sec after the system is disarmed. How

to stop this 2 short trip?

A: In any occasion, if you hear 2 short trips every 10 Sec, please check the LCD screen on the

main console, there should be the message. Please press the “Enter Button” to read a message,

the message should indicate either the activation of sensor/ low battery on the sensor or open

sensor so check the sensor location accordingly with the message and upon completion of

inspection/ correction press “Cancel Button on Main Console or Disarm Button on the Remote

Control” to reset a system to stop the 2 trip/ message on the LCD screen.

13) Q: The one of sensor became low battery condition and the system cannot arm. What

to do?

A: Of cause the best way to correct this problem is to replace the battery. But if you do not have

the battery but you want to arm the system, please press “Cancel Button on Main console or

Disarm Button on Remote Control” to reset a system then arm the system. But please make sure

to replace the battery for that sensor as soon as possible otherwise there might be no indication

of low battery condition again so you may forget the low battery condition/ disability of that

sensor.

14) Q: What is the communication range between the sensor and the main console?

A: In the ideal open space condition, the communication range is about 130’ but this distance will

change depend on the object between them.

15) Q: If there is no telephone number is programmed into the main console and the telephone

line is not connected. Is the system work properly?

A: Yes, the system will work without connection of telephone line but, of cause, the auto dialer

function will not work.

16) Q: How long the battery on the sensor last?

A: Generally, the battery on the sensor will last for about 6 month but it depends on the frequency

of sensor activation. Please keep in mind that the sensors are always “On” regardless of the

system status (Arm/ Disarm) and it will transmit signal whenever it is triggered.

17) 17) Q: How many telephone number will dial out and how when the auto dialer function

is activated?

A: The basically auto dialer will dial out 4 preset telephone numbers (If all preset numbers are

programmed) in the following sequence; The first number to dial out is one of priority number

depend on the occasion of alarm (i.e. Burglary: Preset # 4, Fire: Preset # 5, Medical: Preset # 6)

and follow by the general numbers Preset # 1, 2 and 3. This dial sequence will repeat for 3

cycles.

If the “Dial Set” menu is set to “All”, the auto dialer will stop dialing when all numbers in

sequence are answered or 3 cycle dialing is completed. Note: The answered number will be

excluded from the dial sequence. If the “Dial Set” menu is set to “Single”, the auto dialer will

stop dialing when the one of number in sequence is answered or 3 cycle dialing is completed.

18) Q: How to replace the peripheral unit when it becomes defective?

A: If the “Learning Number” for that defective peripheral unit is recorded/ available, use the menu

“Replace” and enter the “Learning Number” then replace with same type of peripheral unit

(Example: “Door Sensor for Door Sensor, PIR for PIR and so on).

If the “Learning Number” for that defective peripheral unit is unknown but there is unused zone is/

are available, please add a new peripheral unit to the system via menu “SEQ” and record

“Learning Number, Assigned Zone and Location” of new peripheral unit for future use.

Note: The “Learning Number” is the number 1~63 and it correspond to the programmed order

number example the 1st to programmed peripheral unit in to the system will be assigned as 1 and

2nd one to programmed into the system will be assigned as 2 and so on.

19) Q: How to erase the preset telephone number from the system?

A: Use “System Option Menu” and get a preset number which you wish to delete then enter “0”

and press “Enter Button” upon completion of this procedure the above preset number will be

erased.

20) Q: After programming the “Door/ Window Sensor” to “Door Sensor”. Can this sensor convert

to the “Window Sensor”?

A: Unfortunately “No”, you can not change the peripheral unit type for already programmed zone.

Unless erase all programmed peripheral units from the system and then reprogram all peripheral

units again to properly change the peripheral unit type of particular peripheral unit in this case

“Door Sensor to Window Sensor”.

21) Q: The exit delay period cannot set properly and the system will activate soon as open the

door even though the door is opened before the expiration of set exit delay period.

A: Please check the “Door/ Window” sensor setting. If this sensor is used for door, the sensor

should be set to “Door Mode”. Otherwise the sensor will activate the system because the

“Window Sensor” is located on the “Instant Trigger Zone”.

Andere Handbücher für WA-410

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lorex Sicherheitssystem Handbücher

Lorex

Lorex SHS-2S Bedienungsanleitung

Lorex

Lorex SC21CD5444UQ-A80 Bedienungsanleitung

Lorex

Lorex LW2400 Series Bedienungsanleitung

Lorex

Lorex SHS-2S7LD Series Bedienungsanleitung

Lorex

Lorex SILVANIA SY15F6584 Bedienungsanleitung

Lorex

Lorex SG15F5584 Bedienungsanleitung

Lorex

Lorex LW491HD Bedienungsanleitung

Lorex

Lorex LW2301 Series Bedienungsanleitung

Lorex

Lorex LW2960 SERIES Bedienungsanleitung

Lorex

Lorex SG6231 Bedienungsanleitung

Lorex

Lorex QLR1660 Bedienungsanleitung

Lorex

Lorex LW2770 SERIES Bedienungsanleitung

Lorex

Lorex L15LD400 series Bedienungsanleitung

Lorex

Lorex SHS-2S7LD Series Bedienungsanleitung

Lorex

Lorex LW2201 Series Bedienungsanleitung

Lorex

Lorex SG21FD3044-161 Bedienerhandbuch

Lorex

Lorex LW2602 Bedienungsanleitung

Lorex

Lorex SG15F6584 Bedienungsanleitung

Lorex

Lorex LW1000P Series Bedienungsanleitung

Lorex

Lorex L15LD420 SERIES Bedienungsanleitung

Lorex

Lorex SG21CD7444UQ-A80 Bedienungsanleitung

Lorex

Lorex SG 6040 Bedienungsanleitung

Lorex

Lorex L222A8D Series Bedienungsanleitung

Lorex

Lorex L21Q784 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung