Louroe AP-16TB-RM Bedienungsanleitung

MODEL AP-16TB-RM

AP-16TB-RM

8 ZONE AUDIO BASE STATION

INSTALLATION AND OPERATING INSTRUCTIONS

6955 VALJEAN AVE, VAN NUYS, CA 91406

PH: (818)994-6498 / FAX: (818)994-6458

/ www.louroe.com[email protected]

Page 1 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

Ap_16tb_rm_inst_3/15

Contents Description

AP-16TB-RM 8 Zone Rack Mounted Two-Way

Audio Base Station. Used for two-way

communication to remote

speaker/microphone units. Has Audio

IN/OUT for a recorder.

Dual RCA Cable RCA cable for connection to a

DVR/VCR or other Audio devices

that accept line level input

(0dB @ 600W).

AD-3 +24Vdc, 1.5A power supply for powering

both the unit and the remote speaker/

microrophones

INTRODUCTION

The AP-16TB-RM is a sixteen zone rack mounted audio base station with 2-way talk/listen capabilities. It contains a built-

in microphone and speaker for two-way audio communication to the remote station. Unit has volume adjustments for both

talk and listen. Zone audio can be activated by manually pressing the zone activation switches of the unit. Provides 16 line

level RCA outputs for recording remote microphone audio to DVRs with multiple audio inputs. Selectable Audio output and

input from a recorder are provided through RCA connectors at the rear of the unit. Has built-in speaker for listening to live

audio. Compatible with all Louroe’s two-way remote speaker/microphone units. Compatible with Louroe

Speaker/Microphone Models TLI, TLO, TLMC, TLM

[1] - Zone Selector Switches Selects zone for monitoring. Press switch of desired zone to listen to live

monitored audio. Pressing any switch also provides a switch closure for

activating a camera, etc. (100mA max)

[2] - Filter-OUT Indicator Lights (green) when audio filter is not in use. Indicates power is “ON”.

[3] - Filter-IN Indicator Lights (amber) when Filter Switch[6] is pressed to “ON” position.

[4] - VCR-IN Indicator Lights (yellow) when VCR Switch[7] is pressed to “ON” position.

[5] - Overload Indicator Current overload indicator. Lights (red) when power short circuit occurs.

[6] - Filter Switch Used only when audio playback is from a 12 or 24 hr. time lapse

recorder. Press Filter Switch[6] to illuminate red LED for 12/24 hour

mode. This enhances the quality of recorded audio playback. If

playback is from a DVR, filter switch is not used and should be in the

“OUT” position. If no recording device is used, then filter switch must be

in the “OUT” position. Otherwise live audio will be muted. The green

LED illuminates when filter switch is in the “OUT” position.

[7] - VCR Switch Press switch to “ON” (or “IN”) position after connecting DVR/VCR to unit.

(When switch is “OUT”, audio bypasses the DVR/VCR and is not

recorded. When switch is “IN”, audio is sent in for recording and

playback. Switch must always be “IN” whenever a recorder is

connected.

[8] - Talkback switch Press to talk to remote speakers. Select a zone by pressing any Zone

Selector Switch[1] to talk to desired zone. A built-in Talk back

Microphone[10] is located above the Headphone Jack[11].

[9] - Power-Volume Control Knob Rotating knob clockwise turns on power to the unit as indicated by the

filter-OUT indicator[2]. Green LED will illuminate. Rotating clockwise

also increases loudness of monitored audio from the Monitor

Speaker[13].

[10] - Talkback Microphone Built-in microphone for talkback.

[11] - Headphone Jack Used for private listening. Any 3.5mm stereo headphone with 8 to 600W

impedance may be used. Speaker is muted when headphone is used.

[12] - Talkback Control Knob Rotate knob clockwise to increase the loudness of talkback output;

counterclockwise to decrease.

[13] - Monitor Speaker Delivers audio through speaker. Muted when a headphone is plugged

into the Headphone Jack[11].

(not used with DVR’s)

(includes DVR’s)

MIC

POWER-VOLUME

OFF MAX

TALKBACK LEVEL

OFF MAX

SIXTEEN ZONE AUDIO SURVEILLANCE w/ talkback

AP-16TB

MADE IN USA

ZONES

1 2 3 5 6 7 84

PRESS

TALK

HEADPHONES

9 10 11 13 14 15 1612

FILTER

VCR

[1] [2]

[3]

[4]

[5]

[6] [7]

[8]

[9]

[10]

[11]

[12]

Fig. 1 AP-16TB

Front Panel

[13]

INSTALLATION AND OPERATING INSTRUCTIONS

Page 2 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

Ap_16tb_rm_inst_3/15

[14] - Mic 5-Pin Terminal Block Connects to speaker/microphone unit at remote station.

[15] - Audio OUT Jack (RCA) Provides audio to external DVR/VCR, remote amplifiers, etc.

[16] - Aux. Microphone Accepts handheld talkback microphone (8 to 600W) with 1/4” plug.

Works the same as Talkback Microphone[10] and is used as an

option.

[17] - Audio-IN Jack (RCA) Receives audio playback from external DVR/VCR, etc.

[18] - Switch Closure Terminal Block Provides a switch closure when a zone is selected by the Zone

Selector Switch[1]. Maximum current capacity of switch is 100mA.

Do not connect load that will exceed this current rating.

[19] - Zone Aux. Mic Output Used for connection to a DVR with multiple audio inputs or for

(each zone) connecting to another AP-16TB (paralleling two or more units).

NOTE: When paralleling to a second unit, terminal “A” is not

used, as 12 Vdc is supplied to the microphone from the first base

station. Also total microphone cable run must not exceed 1000 ft.

[20] - DC-IN Jack (power) Accepts 24 Vdc from external power supply (AC adapter included).

Fig. 2 Rear of AP-16TB

[14][19] [15]

[17] [16]

[20]

[18]

A B C

1ZONES 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

24Vdc

2A 3A 4A 5A 6A 7A 8A 9A 10A 11A 12A 13A 14A 15A 16A

G A B C SP G A B C SP G A B C SP G A B C SP G A B C SP G A B C SP G A B C SP G A B C SP G A B C SP G A B C SP G A B C SP G A B C SP G A B C SP G A B C SP G A B CSP G AUDIO OUT

AUDIO IN

NOTE REGARDING CONNECTION TO DVR’s:

Model AP-16TB-RM is compatible with most DVR’s

If DVR has only one audio input, connect the “Audio Out” jack on

back panel of AP-16TB-RM to “Audio In”[17] of DVR using an RCA

cable.

If DVR has multiple audio inputs, connect the “Mic Out” jacks[19] on

back panel of AP-16TB-RM to the audio inputs of DVR using RCA

cables.

If DVR contains 3.5mm audio inputs instead of RCA types, a 3.5mm

stereo adapter must be connected to one end of RCA cable.

INSTALLATION AND OPERATING INSTRUCTIONS

Page 3 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

Ap_16tb_rm_inst_3/15

WIRING CONNECTIONS

1). Connect one end of cable to remote speaker/microphone as shown in Fig. 3. Use 4 conductor shielded audio

cable such as West Penn 356. Connect wires wrapped with overall shield to terminals “A”, “B”, and “C” of

microphone’s terminal block. When using West Penn 356, connect red wire to terminal “A”; black wire to terminal

“B” and bare wire to terminal”C”.

2). Connect the two speaker wires (white and green) to speaker’s 70 volt transformer terminals. Connect cable’s

white wire to white wire connected to the 70 volt transformer using a wire nut. Connect cable’s green wire to

green wire of transformer with a wire nut.

3). Connect the other end of the cable to AP-16TB Mic 5-Pin Terminal Block[14] for the zone which the remote

microphone is assigned. Make sure that wire connected to terminal “A” of remote microphone connects to

terminal “A” of unit’s Mic 5-Pin Terminal Block[14]; wire connected to terminal “B’ of microphone connects to

terminal “B” of unit’; “C” to “C”. If using wire from other manufacturers, color code may vary.

4). Connect white speaker wire to Mic 5-Pin Terminal Block[14] terminal “G”. Connect green wire to terminal marked

“SP”.

5). Repeat steps 1 thru 3 for zones 2, 3, 4 .....16.

6). When a recorder is used (DVR, VCR etc.), connect Audio-OUT Jack[15] to recorder’s Audio-IN Jack with an RCA

cable (not supplied).

7). Connect Audio-IN Jack[17] to recorder’s Audio-Out Jack.

8). Plug AC Adapter (supplied) to DC-IN Jack[20].

NOTE: If AP-16TB-RM is to be used as a one-way listen only system (no talkback), any Louroe Verifact Microphone can

be used. Make microphone connections as described above (see step 1). Disregard speaker connections. Use 2

conductor shielded cable, 22 gauge with a 24 gauge drain. West Penn 452 or equivalent. Same color code as in

West Penn 356 (red, black and bare).

Fig. 3 Interconnection Diagram

A B C

1ZONES 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

24Vdc

2A 3A 4A 5A 6A 7A 8A 9A 10A 11A 12A 13A 14A 15A 16A

G A B C SP G A B C SP G A B C SP G A B C SP G A B C SP G A B C SP G A B C SP G A B C SP G A B C SP G A B C SP G A B C SP G A B C SP G A B C SP G A B C SP G A B CSP G AUDIO OUT

AUDIO IN

OUT IN

EXAMPLE CABLE:

WEST PENN 356

2 CONDUCTOR SHIELDED #20 AWG

2 CONDUCTOR UNSHIELDED #18 AWG

1 DRAIN WIRE (BARE) #22 AWG

REAR OF AP-16TB

REAR OF DVR/VCR

Louroe Model TLSP Speaker/Microphone

AUDIO

AC ADAPTER

RED

BLACK

BARE

WHITE

GREEN

WHITE

WIRE NUT

INSTALLATION AND OPERATING INSTRUCTIONS

Page 4 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

Ap_16tb_rm_inst_3/15

AB C

VERIFACT A

RED(A)

BLACK(B) BARE(C)

ABCSP GAL

BARE

GREEN

IMPORTANT NOTICE

When this equipment is used as part of an audio

monitoring system, the law requires that the public

be given notice of AUDIO MONITORING ON THE

PREMISES. A decal notice is included with each

microphone shipped.

Federal Law References:

Federal Regulations, US Code, Title 18. Crime and

Criminal Procedure, Sec 2510.

AUDIO

MONITORING

LOUROE

LECTRONICS

These Premises

RED

BLACK

OPERATION AND TEST

1). To apply power, first connect small end of 24 Vdc power supply to the 24 Vdc power jack located on rear

panel [20], then plug power block into a standard 120 Vac wall outlet or power strip.

2). Turn on power to the unit by rotating the Power-Volume Control Knob[9] clockwise to “ON” position.

Filter-OUT Indicator[2] should light green, indicating power is present at the unit. Rotate

Power-Volume Knob[9] further clockwise to increase the level of loudness of monitored audio.

3). Press Zone Selector Switches[1] marked zone 1. Audio from zone 1 should be present at the Monitor

Speaker[13]. If there is no audio, temporarily remove wires connected to Mic 5-Pin Terminal Block[14] for

zone 1 located at the rear of the unit. With a voltmeter, check that 12 Vdc is present at terminals “A” and

“C”. Place positive lead of voltmeter to terminal “A” and negative to “C”. If voltage is not present, unit has

defective voltage regulator. If voltage is present, check to see if the wires are connected properly to the

right terminals. Otherwise microphone is defective. Call factory for assistance.

4). Press Talkback Switch[8] and speak into the Talkback Microphone[10]. Rotate Talkback Volume

Control[12] clockwise to increase the level of talkback audio. Another person is needed at the remote

location to listen to the volume and clarity of talkback audio.

5). Repeat steps 3 and 4 for the other zones.

6). When a 24 hour VCR is connected to the unit, press VCR Switch[7]. VCR-IN Indicator[4] will light yellow.

Start recording live audio. It is not necessary to use VCR switch if recording into a DVR. The VCR

Switch[7] must be in the “OUT” position when a recorder is not connected to the unit. Otherwise live

audio will be muted.

7). Recorded audio can be played back through the AP-16TB-RM’s built-in amplifier and speaker. If audio

playback is from a 24 hour time lapse recorder, press Filter Switch[6] to 12/24 hour mode. Filter In

indicator[3] will illuminate red. If playback is from a DVR, filter switch is not used and should be in the

“OUT” position. If no recording device is used, then filter switch must be in the “OUT” position. Otherwise

live audio will be muted. The green LED will illuminate when filter switch is in the “OUT” position.

SPECIFICATIONS

Monitor power output

Talkback power output

1W @ 8W

1.5W into 70V line

Audio input impedance 10kW

Audio frequency response 100 Hz to 10kHz

Audio frequency

response (enhanced)

-20 dB @ 200 Hz to

+5dB @ 3kHz

Headphone impedance 8 to 600W

Power input 24 Vdc, 1.5A

Dimensions 19”L x 7”W x 12 1/2”D

Weight

Shipping Weight

10 lbs 14 oz

15 lbs

Input sensitivity -45 dB

(Talkback microphone)

Audio line output impedance 600W

Switch Closure Rating 100mA

INSTALLATION AND OPERATING INSTRUCTIONS

Page 5 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

Ap_16tb_rm_inst_3/15

NOTES

INSTALLATION AND OPERATING INSTRUCTIONS

Page 6 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

Ap_16tb_rm_inst_3/15

IMPORTANT NOTICE

When this equipment is used as part of an

audio monitoring system, the law requires

that the public be given notice of AUDIO

MONITORING ON THE PREMISES. A

decal notice is included with each

microphone shipped.

Federal Law References:

Federal Regulations, US Code, Title 18.

Crime and Criminal Procedure, Sec 2510.

INSTALLATION AND OPERATING INSTRUCTIONS

Page 7 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

AUDIO

MONITORING

These Premises

WARRANTY

LOUROE ELECTRONICS warrants that at the time of shipment products manufactured by LOUROE ELECTRONICS to be free of defects in material and workmanship.

Should a defect appear within one year (12 months) from date of shipment, LOUROE ELECTRONICS will, at its sole discretion, repair or replace the defective equipment.

This equipment shall not be accepted for repair or return without prior notification by LOUROE ELECTRONICS .

This warranty does not extend to any Louroe product that has been subjected to improper or incorrect installation, misuse, accident, or in violation of installation

instructions provided by LOUROE ELECTRONICS.