Loveshaw LITTLE DAVID LDXCRS Bedienungsanleitung

LDXCRS

THE LOVESHAW CORPORATION LOVESHAW - EUROPE

2206 EASTON TURNPIKE UNIT 9, BRUNEL GATE

SOUTH CANAAN, PA 18459 W. PORTWAY INDUSTRIAL ESTATE

ANDOVER,HAMPSHIRESP103SL

TEL: (570) 937-4921 ENGLAND

FAX: (570) 937-4370 44-264-3575-11

OWNERS

MANUA

LOVESHAW an ITW Company

TABLE OF CONTENTS

SUBJECT

GENERAL SAFETY PRECAUTIONS

MACHINE LABELS

MACHINE SPECIFICATIONS

INTRODUCTION

INSTALLATION

OPERATION

MAIN FRAME

HEAD

ELECTRICAL SYSTEM

LUBRICATION

TROUBLE - SHOOTING

TAPE CARTRIDGE

WARRANTY

ILLUSTRATED REPLACEMENT PARTS

TABLE OF CONTENTS

LOVESHAW an ITW Company

GENERAL SAFETY PRECAUTIONS

BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT, READ THE FOLLOWING

PRECAUTIONS CAREFULLY:

* ALWAYS DISCONNECT POWER AND AIR SUPPLY (IF APPLICABLE) BEFORE SERVICING THE MACHINE.

REFER TO YOUR COMPANY’S LOCK OUT/TAG OUT PROCEDURES.

* THIS MACHINE IS EQUIPPED WITH MOVING BELTS. DO NOT PLACE HANDS NEAR THE REAR OF THIS

MACHINE WHEN BELTS ARE MOVING, AS FINGERS MAY BE PINCHED WHERE BELTS ENTER FRAME.

(SEE MACHINE LABELS, NEXT PAGE) ALWAYS USE A ROLLER TYPE EXIT CONVEYOR AND ALWAYS

REMOVE THE BOXES AFTER THEY CLEAR THE EXIT END OF THE MACHINE.

* OBSERVE CAUTION WHEN NEAR CARTRIDGE KNIFE OR WHEN THREADING TAPE. (SEE MACHINE LABELS,

NEXT PAGE) KNIFE IS VERY SHARP, AUTOMATICALLY OPERATED AND IS LINKED TO THE WIPE DOWN ROLLERS.

* DO NOT ATTEMPT TO OPEN OR WORK ONELECTRICAL BOX, JUNCTION BOXES, OR OTHER ELECTRICAL

COMPONENTS WITHOUTFIRST DISCONNECTING POWER TO THE MACHINE. REFER TO YOUR COMPANY’S

LOCK OUT / TAG OUT PROCEDURES. SHOCK HAZARD EXISTS IF POWER IS NOT DISCONNECTED.

(SEE MACHINE LABELS, NEXT PAGE).

* DO NOT BY-PASS ANY DESIGNED-IN SAFETY FEATURES SUCH AS INTERLOCKS, GUARDS OR SHIELDS.

* DO NOT PLACE HANDS OR BODY INSIDE CONFINES OF UNIFORM TYPE MACHINES UNLESS HEAD IS

SECURELY LOCKED AND POWER AND AIR ARE DISCONNECTED.

* WHEN OPERATING A SEMI-AUTOMATIC MACHINE, HOLD BOX FLAPS DOWN AT TRAILING EDGE OF THE

BOX. RELEASE HANDS AS SOON AS THE BELTS TAKE THE BOX.

* DO NOT WEAR JEWELRY, LOOSE CLOTHING, SUCH AS TIES, SCARVES, ETC. AND LONG HAIR SHOULD BE

PULLED BACK WHEN OPERATING THE MACHINE. (SEE MACHINE LABELS, NEXT PAGE).

* SAFETY GLASSES SHOULD BE WORN WHEN WORKING ONOR AROUND THE MACHINE.

* WHEN MOVING A MACHINE WITH CASTERS OPTION, HEAD SHOULD BE IN THE LOWEST POSSIBLE POSITION.

ALWAYS MOVE MACHINE IN THE SAME DIRECTION AS THE LONG AXIS, NEVER PUSH MACHINE IN DIRECTION

OF THE SHORT AXIS. SEE FOOTPRINT DRAWING.

* MACHINE LABELS (SEE NEXT PAGE) ARE PLACED ON THE MACHINE FOR YOUR SAFETY. LABELS SHOULD

BE INTACT AND LEGIBLE. REPLACE LABELS IF THEY ARE WORN, DAMAGED, PEELING, OR ILLEGIBLE.

LOVESHAW an ITW Company

MACHINE SPECIFICATIONS

MACHINE DIMENSIONS:

HEIGHT: 61.5 inches 1562.1 mm

WIDTH: 38 inches 965.2 mm

LENGTH: 56 inches 1422.4 mm (with front pack table)

TABLE HEIGHT (adjustable):

MINIMUM: 22.5 inches 571.5 mm

MAXIMUM: 28.5 inches 723.9 mm

ELECTRICAL:

STANDARD: 115V/1/60

240V/1/50

OPTIONAL: 220V/1/50,60

220V/3/50,60

380V/3/50

440V/3/50

440V/3/60

BOX CAPACITY:

LENGTH: 4.5 inches to 114.3 mm to

unlimited max. unlimited max.

WIDTH: 5.5 inches to 139.7 mm to

27 inches 685.8 mm

HEIGHT: 4.5 inches to 114.3 mm to

24 inches 609.6 mm

OPERATING SPEED:

BELT SPEED: 80 ft / min. 18 m/min.

NUMBER OF BOXES/MIN.: VARIES WITH BOX SIZE

CLOSURE MATERIAL - PRESSURE SENSITIVE TAPE

WIDTH: 1.5 inches to 38 mm to

2 inches 50 mm

MAX. ROLL DIAMETER: 15 inches 380 mm

WEIGHT: (uncrated) 180 lbs. 81 kg.

LOVESHAW an ITW Company

INTRODUCTION

THE LITTLE DAVID LDXCRS UNIFORM PRESSURE SENSITIVE TAPER IS DESIGNED TO TAPE TOP AND BOTTOM FLAPS

OF A WIDE VARIETY OF BOX SIZES. AFTER MANUALLY ADJUSTING THE MACHINE FOR THE BOX SIZE, THE OPERATOR

ONLY HAS TO FOLD THE FLAPS AND PUSH THE BOX INTO THE MACHINE AFTER WHICH THE MACHINE WILL TAPE THE TOP

AND BOTTOM FLAPS AND DISCHARGE THE BOX.

THE SIMPLE BUT SOPHISTICATED DESIGN INSURES A MINIMUM OF MAINTENANCE PROBLEMS AND THE MACHINE CAN BE

EASILY OPERATED BY UNSKILLED OPERATORS. DUE TO ITS SMALL SIZE AND SIMPLE PLUG-IN CONNECTION, IT CAN BE

QUICKLY MOVED TO THE AREA WHERE IT IS NEEDED. IT MAY STAND ALONE OR IF DESIRED, BE INCORPORATED IN A

CONVEYOR SYSTEM.

THE FINEST MATERIALS AND WORKMANSHIP HAVE BEEN EMPLOYED TO INSURE SATISFACTION. IF ADJUSTMENTS

OR REPAIRS BECOME NECESSARY YOU WILL FIND SIMPLE INSTRUCTIONS OUTLINED IN THIS MANUAL. IF A PROBLEM

OCCURS WHICH IS NOT COVERED IN THE MANUAL, PLEASE TELEPHONE OUR SERVICE DEPARTMENT AT:

LOVESHAW CORPORATION

2206 EASTON TURNPIKE, BOX 83

SOUTH CANAAN, PA 18459

PHONE: 1-800-962-2633 / 570-937-4921

LOVESHAW - EUROPE

UNIT 9 BRUNEL GATE

WEST PORTWAY INDUSTRIAL ESTATE

ANDOVER, HAMPSHIRE SP10 3SL

ENGLAND

OR YOUR NEAREST LITTLE DAVID DISTRIBUTOR

LOVESHAW an ITW Company

INSTALLATION

FOR DOMESTIC CUSTOMERS ONLY - THE LITTLE DAVID IS SHIPPED COMPLETELY ASSEMBLED.

THE LITTLE DAVID IS READY FOR OPERATION AFTER PLUGGING IT INTO AN APPROPRIATE GROUNDED ELECTRICAL OUTLET.

THE CONNECTION CABLE IS LOCATED ON THE SIDE OF THE MACHINE.

THE HEIGHT OF THE MACHINE CAN BE ADJUSTED FROM 22.5 INCHES TO 28.5 INCHES (571.5 mm to 723.9 mm) BY ADJUSTING THE

HEIGHT OF THE LEG EXTENSIONS.

THE MACHINE SHOULD BE PLACED ON A FLAT LEVEL FLOOR SO THAT IT DOES NOT ROCK. DUE TO ITS PORTABILITY AND EASY

PLUG-IN CONNECTION, THE MACHINE MAY BE QUICKLY MOVED TO VARIOUS LOCATIONS AS THE NEED ARISES. OPTIONAL

CASTERS ARE AVAILABLE, IF REQUIRED. THERE ARE HOLES PROVIDED IN THE LEG EXTENSION PADS FOR ANCHORING, IF

REQUIRED.

AN OPTIONAL INFEED TABLE CAN BE INSTALLED AT THE INFEED END OF THE MACHINE, HOWEVER, A CONVEYOR MAY BE

USED INSTEAD. THE INFEED TABLE CAN BE USED SO THAT THE PACKER CAN FILL THE BOXES AND CLOSE THE FLAPS PRIOR

TO FEEDING THE BOXES IN THE MACHINE. A CONVEYOR SHOULD BE PROVIDED AT THE OUT FEED END OF THE MACHINE TO

RECEIVE THE BOXES AS THEY ARE DISCHARGED FROM THE MACHINE. IMPORTANT: BE SURE THE TABLE AND CONVEYOR

ARE 1/4” (6 mm) BELOW THE MACHINE BELT HEIGHT.

LOVESHAW an ITW Company

OPERATION

AFTER THE TAPE CARTRIDGES ARE LOADED, THE MACHINE IS READY TO SEAL BOXES. PLACE A SAMPLE BOX OF THE SIZE

TO BE SEALED ON THE INFEED TABLE, FOLD THE FLAPS AND PUT JUST IN FRONT OF THE TOP TAPE CARTRIDGE. RELEASE

THE SIDE RAILS BY TURNING THE SIDE RAIL LOCK HAND WHEEL COUNTERCLOCKWISE AND MOVE THE SIDE RAILS IN UNTIL

BOTH RAILS ARE IN CONTACT WITH THE BOX. LOCK THE SIDE RAILS BY TURNING THE HAND WHEEL CLOCKWISE. RELEASE

THE HEAD LOCK HAND WHEEL COUNTERCLOCKWISE. LOWER THE HEAD UNTIL IT MAKES CONTACT WITH THE BOX; THEN

PUT A SLIGHT ADDITIONAL PRESSURE ONTHE BOX. LOCK THE HEAD BY TURNING THE HEAD LOCKHAND WHEEL

CLOCKWISE.

START THE MACHINE WITH THE START SWITCH LOCATEDON THE OPERATOR SIDE OF THE MACHINE. NOW THE SAMPLE

BOX WILL BE TAPED AND DISCHARGED. THE MACHINE IS NOW READY TO PROCESS BOXES.

THE PACKER SHOULD FOLD THE BOX FLAPS IN THE NORMAL MANNER AND WHILE HOLDING THEM CLOSED ON THE REAR

OF THE BOX, SHOULD FEED THE BOX INTO THE MACHINE UNTIL THE BELTS TAKE IT FROM HIM. THE MACHINE WILL SEAL

THE TOP AND BOTTOM FLAPS AND DISCHARGE THE BOX TO THE OUT FEED CONVEYOR AUTOMATICALLY.

LOVESHAW an ITW Company

MAIN FRAME

STARTER SWITCH:

THE STARTER SWITCH IS MOUNTED ON THE OPERATOR SIDE OF THE MACHINE. IT INCORPORATES A CIRCUIT BREAKER

THAT IS SET TO TRIP AT THE PROPER RATING OF THE MOTOR. TO REPLACE THIS SWITCH, FIRST DISCONNECT THE

MACHINE FROM THE ELECTRICAL SUPPLY. REMOVE THE SWITCH BY LOOSENING SCREWS HOLDING THE ENCLOSURE

CLOSED. REMOVE ENCLOSURE TO EXPOSE MOTOR STARTER. REMOVE THE WIRES, FIRST NOTING THEIR CONNECTIONS

TO THE SWITCH. SLIDE SWITCH SIDEWAYS AND UP TO REMOVE.

TO REPLACE THE STARTER SWITCH, REVERSE THE ABOVE PROCEDURE.

SIDE RAILS:

THE SIDE RAILS CENTER AND ALIGN THE BOX AS IT IS BEING PROCESSED. THEY ARE SET MANUALLY BY LOOSENING

THE SIDE RAIL LOCK HAND KNOB COUNTERCLOCKWISE. MOVE THE SIDE RAILS IN UNTIL BOTH SIDE RAILS COME IN

CONTACT WITH THE BOX. RELOCK THE SIDE RAILS BY TURNING THE SIDE RAIL LOCK HAND KNOB CLOCKWISE.

BELTS:

TWO ENDLESS BELTS LOCATED ON THE BED OF THE MACHINE DRIVE THE BOX THROUGHTHE MACHINE. THE BELTS

RUN OVER A DRIVE ROLLER LOCATED AT THE EXIT END OF THE MACHINE, AND ARE POSITIONED OVERTHE INFEED

ROLLERS LOCATED AT THE INFEED END.

TO REPLACE BELT, PULL OUT BELT TENSION HANDLE TO REMOVE TENSION. SLIDE BELT OFF OF FRONT ROLLER AND

THEN OFF REAR DRIVE ROLLER TO REMOVE. TO INCREASE/DECREASE TENSION WHEN HANDLE IS IN OUT POSITION

ROTATE TENSION KNOB TO CHANGE TENSION. REPLACE BELT MAKING SURE IT IS POSITIONED IN BELT GUIDE TRACK.

CLOSE HANDLE MAKING SURE NOT TO OVER TENSION BELTS.

EACH BELT IS REPLACED SEPARATELY, HOWEVER, IT IS RECOMMENDED THAT BOTH BELTS BE REPLACED AT THE SAME

TIME. IT IS IMPORTANT THAT FACTORY SUPPLIED BELTS BE USED SINCE THEY ARE OF SPECIAL CONSTRUCTION.

LOVESHAW an ITW Company

HEAD

THE HEAD RIDES ALONG THE MAST ON BEARINGS AND HIGH DENSITY POLYETHYLENE PADS. THE HEAD HEIGHT IS ADJUSTED BY

TURNING THE HEAD VIBRATION LOCK KNOB COUNTERCLOCKWISE TO RELEASE THE HEAD. TURNING THE HAND CRANK CLOCKWISE

WILL RAISE THE HEAD TO THE DESIRED POSITION.

BEARINGS:

IF ANY OF THE BEARINGS WHICH RUN AGAINST THE MAST NEED TO BE REPLACED, PROCEED AS FOLLOWS:

- DISCONNECT ELECTRICAL SUPPLY. PLACE A STURDY BOX/BLOCK ON BED OF MACHINE AND LOWER

HEAD ONTO IT.

- REMOVE THE HARDWARE AND SNAP RINGS FROM THE SIDES OF THE HEAD TO REMOVE TROLLEY BEARINGS.

- BACK OFF NUTS BETWEEN BEARINGS WHILE TURNING THREADED SHAFT WITH A SCREW DRIVER UNTIL

DEFECTIVE BEARING CAN BE REMOVED.

- REVERSE ABOVE PROCEDURE TO REPLACE BEARING.

WHENEVER THE BEARINGS HAVE BEEN CHANGED, THE CLEARANCE BETWEEN THE HEAD AND THE MAST MUST BE RE-ALIGNED.

THE CLEARANCE BETWEEN THE TEFLON SLIDES AND THE SIDES OF THE MAST SHOULD BE ADJUSTED TO APPROXIMATELY

.020” (.5 mm). THIS SHOULD BE CHECKED THROUGH THE HEADS RANGE OF TRAVEL TO INSURE THAT THIS CLEARANCE EXISTS

AT THE HIGH POINTS OF THE MAST.

THE CLEARANCE BETWEEN THE BEARINGS AND THE FRONT AND REAR SURFACES OF THE MAST SHOULD BE SUCH THAT THE

HEAD MOVES FREELY AND DOES NOT COCK OR SAG.

ELECTRICAL SYSTEM

THE ELECTRICAL SYSTEM CONSISTS OF A FRACTIONAL HP DRIVE MOTOR AND THE STARTER SWITCH.

THE MOTOR AND FRAME ARE GROUNDED THROUGH THE ELECTRICAL CONNECTOR.

THE CIRCUIT BREAKER IS FACTORY SET. IF IT TRIPS, IT SHOULD BE RESET AFTER INSPECTION OF THE

ELECTRICAL SYSTEM.

WARNING: THE INSPECTION OF THE ELECTRICAL SYSTEM SHOULD BE DONE BY A QUALIFIED

ELECTRICIAN ONLY!

LOVESHAW an ITW Company

LUBRICATION

ALL MECHANICAL PARTS ON THE LITTLE DAVID ARE PERMANENTLY LUBRICATED AND SEALED BEARINGS ARE

USED THROUGHOUT.

THE REDUCER IS A SEALED UNIT.

THE MAST SHOULD BE CLEANED AND SPRAYED WITH A SILICONE LUBRICANT - THIS SHOULD BE DONE ON A

WEEKLY BASIS TO ENSURE FREE MOVEMENT OF THE HEAD.

Inhaltsverzeichnis

Andere Loveshaw Verpackungsanlagen Handbücher

Loveshaw

Loveshaw Little David CF50T Bedienungsanleitung

Beliebte Verpackungsanlagen Handbücher anderer Marken

U-Line

U-Line S-15188 Bedienungsanleitung

ITATOOLS

ITATOOLS ITA22 Bedienungsanleitung

Fieldpiece

Fieldpiece MG44 Bedienungsanleitung

Smart wasp

Smart wasp X300 Bedienungsanleitung

U-Line

U-Line S-1135 Bedienungsanleitung

Z.R. Tools

Z.R. Tools MS25-1 Bedienungsanleitung

Sipromac

Sipromac SIPROVAC 620A Bedienungsanleitung

strapex

strapex STR 66 Bedienungsanleitung

U-Line

U-Line H-5334 Bedienungsanleitung

Imetec

Imetec Q5901 Bedienungsanleitung

Transpak

Transpak TP-201 Leitfaden

Lacor

Lacor 69352 Technisches Datenblatt

Eastey

Eastey EXS-100 Bedienungsanleitung

Inova

Inova SV 125 Bedienungsanleitung

CombiSteel

CombiSteel 7529.0010 Bedienungsanleitung

HUALIAN

HUALIAN HVC-260T/1A Bedienungsanleitung

U-Line

U-Line H-2079 Bedienungsanleitung

Strapack

Strapack iQ400 Betriebsanleitung