Lowrance X67C Bedienungsanleitung

Pub. 988-0151-152

Addendum I

X67C IceMachine

Since the manual was written for the X67C, specialized features and ac-

cessories have been added to create the X67C IceMachine, a portable

color ice fishing sonar. The IceMachinepackage includes the X67C so-

nar unit and the PPP-15 portable power pack. The PPP-15 includes a

self-leveling ice fishing transducer, a rechargeable battery and a freeze-

resistant carry bag.

Each X67C unit contains a menu command that allows you to switch the

sonar in and out of IceMachine mode. If you purchased a regular X67C

package with the Skimmertransom-mount transducer, you can buy the

PPP-15 separately. If you purchased an IceMachine package, you can

buy a Skimmer transducer separately with mounts for transom, trolling

motor or portable suction-cup installations.

These accessory combinations and the unit's digital flashers and scrolling

chart display make the X67C the most versatile ice fishing sonar in its

class. Owning an X67C is like having two fish finders in one, because it's

equally at home on a boat in summer or on the ice in winter.

The main manual, part number 988-0151-062, introduces you to the

X67C, and it covers general warm weather operations. Introductory ma-

terial is only discussed in the main manual. You should be familiar with

those basic functions before you head for the ice. A good place to start is

the Basic Sonar Operation section, beginning on page 27, or the one-page

Basic Sonar Quick Reference, on page 34.

This addendum covers the basic ice fishing functions and any other op-

erational changes that may have occurred since the manual was pub-

lished. In addition to the instructions found here, be sure to read the

PPP-15 instruction booklet, part number 988-0147-871. It will tell you

how to set up the ice fishing power pack and mount the X67C.

Topics discussed in this document include:

Introduction to IceMachine Mode

•Your unit now has five pages that display sonar information.

IceMachine Mode Operation

•Sensitivity

•ColorLine

•Battery gauge.

Sonar Signal Interpretation

•Signal band movement means fish.

•Signal band color and fish position.

•Signal band thickness and fish size.

Ice Flasher Options

•Split Zoom display mode

•Color Modes.

Scouting Through the Ice

•You can hunt for fish before you ever drill a hole by scanning

through the ice.

Introduction to IceMachine Mode

Your unit has five pages that display sonar information. In addition to

Full Sonar Chart, Split Zoom Sonar Chart, Digital Data and Flasher,

there is the Ice Flasher. This new page is only visible in IceMachine

Mode. You can tell at a glance which mode you are in because the battery

gauge only appears in the lower right corner of the Ice Flasher page.

Ice Flasher page, left, and normal Flasher page, right.

The ice mode differs from normal mode in two ways. First, the unit

changes how it filters incoming sonar echoes. This helps reduce some of

the surface clutter that can be picked up from the zone where the water

surface meets the bottom of the ice.

Second, the Ice Flasher defaults to a special IceView color mode with

fewer, higher-contrast colors than normal mode. This simplified color

scheme makes it easier to "see" and interpret a fish signal when it ap-

pears on the flasher screen.

The Split Zoom and Sonar Chart pages share the same settings. The chart

pages, the Flasher and Ice Flasher pages each have their own independent

controls for Sensitivity, ColorLineand sonar color mode. For example, if

you make any Sensitivity changes to the sonar chart page, the sensitivity

settings for the Flasher and Ice Flasher are unchanged. Each of these set-

tings are saved when you turn the unit off, so you can keep your favorite

settings for each operating mode.

Remember, no matter what changes you make to the various settings,

you can always restore the factory defaults by using the Reset Options

command, which is described on page 55 in the manual.

IceMachine Mode Operation

To turn on the X67C, press and release the MENU key. (This is actually

the Menu/Power key, but in the text we just refer to it as the "Menu"

key for short.) The Backlight control will appear for five seconds and

then automatically clear. You can adjust it with the ↓and ↑buttons, or

clear it immediately by pressing the EXIT button.

At left, X67C IceMachine opening screen, showing the Full Sonar Chart

Page. The Backlight Level control bar automatically disappears after

five seconds. At right, the Full Sonar Chart is shown.

You access the various page displays by pressing the ENT/PAGES key.

As you press this key, the unit cycles through the page options. To re-

turn to a previous page, simply press ENT repeatedly until the desired

page appears again. (It serves multiple functions, but we'll refer to this

key in the text as simply the ENT key.)

NOTE:

We use a type of "menu shorthand" to describe how to work your so-

nar. To understand our typographical and instruction conventions, see

the segment How to Use this Manual on pages 3-4 in the X67 manual.

To enter the IceMachine mode:

1. From the Full Chart Sonar page, press ENT|ENT|ENT to switch to

the normal Flasher page.

2. Press MENU|↓to ICEMACHINE MODE|ENT|EXIT and the Ice Flasher ap-

pears. (To leave IceMachine mode and return to normal operation, just

repeat step 2.)

Flasher Page Menu, with IceMachine Mode command highlighted but

turned off (box not checked).

The following figure shows the various components of the Ice Flasher

page display.

Ice Flasher page.

Temperature

Bottom Signal

indicator

Bigger fish signal

at 15 feet.

Sensitivity

Control Bar

Echo Strength

Color Scale

Bottom ColorLineshows hard bottom

Surface clutter

signal

Small fish or

bait signals

Digital Depth

Depth Range Scale

Battery capacity

gauge

Surface signal

Sensitivity

Sensitivity and Auto Sensitivity are described in detail in the manual on

page 55. To adjust sensitivity on the Flasher or Ice Flasher page, simply

press ↑to increase sensitivity and press ↓to decrease sensitivity. The

changes are displayed on the horizontal Sensitivity Control Bar. The

Echo Strength Color Scale also changes as you adjust sensitivity.

Important:

Setting Sensitivity for Ice Fishing

The IceMachine's basic operation is pretty easy, right out of the box. If

you're a sonar novice, try operating the unit with the automatic factory

default settings until you get a feel for how it's working.

As you're learning the basics however, Sensitivity is the one important

setting that you should adjust while ice fishing. We strongly recom-

mend you try the following method for "tuning" your sensitivity to

match the current water conditions. It will help you see your bait, cut

through any clutter in the water and dramatically show fish when they

move in to check your offering. As you learn to interpret the signals on

the flasher screen, you'll be able to modify your presentation based on

how fish react to your lure.

To adjust sensitivity:

1. Start with your IceMachine showing the Ice Flasher page, in the de-

fault IceView color mode.

2. Drop your lure five to 10 feet directly below the transducer. You

should be able to follow the fall of the bait on the flasher screen.

2. Use the arrow keys to turn the sensitivity up or down until the lure

is barely visible as a black or blue signal band on the screen.

3. Now fish at the desired depth. When a fish approaches the bait, its

signal will stand out from the lure because it will be a moving signal

that is wider and a brighter color than your lure.

ColorLine

ColorLine is described in detail in the manual on page 43. ColorLine

changes will be reflected in the Echo Strength Color Scale. This scale

considers both sensitivity and ColorLine and then shows you the rela-

tionship of signal strength to signal color. To adjust the ColorLine level:

1. From the Ice Flasher Page, press MENU|↓to COLORLINE|ENT.

2. The ColorLine Control Bar appears. Press ↓to decrease ColorLine;

press ↑to increase ColorLine.

3. When it's set at the desired level, press EXIT.

ColorLine distinguishes between weak and strong sonar signals by

"painting" them with different colors. You can adjust ColorLine to suit

your personal viewing tastes. The left figure shows the default Color-

Line setting. The center figure shows a lower ColorLine setting and at

right, a higher setting. These black and white illustrations don't show

it, but the far left band on the Echo Strength scale is black, followed by

blue, green, yellow and at the far right, red.

In the Ice Flasher, the weakest signals are shown in black and the

strongest signals show as red. Fish are among the weakest echoes, so

they show up mostly as black and blue bands on the flasher screen. The

hardest surfaces, like the bottom, show as red. Cover in the form of

weed beds or submerged timber display in the blue to yellow range.

Battery Gauge

The Ice Flasher has a battery gauge that shows the capacity of the re-

chargeable battery. When the battery is fully charged, the gauge is

filled with green. As power is consumed, the fill level drops and turns to

yellow (70 percent charged) and red (30 percent). When the gauge

shows 0 percent, you should turn off the unit to save your settings, and

then recharge the battery.

This battery gauge is solid green, indicating a full charge.

Sonar Signal Interpretation

When you monitor your flasher screen for signs of fish, there are three signal

band characteristics to watch for: movement, color and thickness.

Signal band movement

In a stationary setting like ice fishing, the bottom, structure and cover

will show on the flasher screen as stationary bands of color. Signals

between the surface and the bottom that come and go or move up and

down (even slightly) will be fish that have appeared inside the sonar

signal cone.

Signal band color

The color of the signal bands correspond to both fish size and their posi-

tion in the sonar signal cone. Black and blue signals tend to be smaller

fish, or fish that are at the outside edge of the sonar cone. These

smaller or more distant fish return weaker echoes.

Red signals are much larger fish, or fish that are in the center of the

sonar cone, almost directly below the transducer. They return the

strongest echoes.

Signals that are yellow and some other color result from mid-sized fish

that are in a transition zone between the center and outer edges of the

sonar cone. They represent medium-strong echoes.

As a fish moves through part of the signal cone, the signal may change

from black to blue to green or yellow then back again. The signals may

appear to move up slightly and then back down, even if the fish doesn't

actually change depth. This is caused by the relative distance from the

transducer to the fish as it passes by the transducer.

Battery charge

indicator

Signal band thickness

Simply put, smaller fish return smaller echoes that result in thinner

and fainter signal bands. A thin signal can also indicate a fish located

toward the outer edge of the signal cone. As fish size increases, the ech-

oes grow stronger and the signal band grows wider. Signal width also

increases as a fish approaches the center of the sonar cone.

Ice Flasher Options

Split Zoom Display Mode

When ice fishing season arrives, you're often searching for fish that are

hugging the warmer water at the bottom of the lake. When walleye or

perch are holding right on the bottom, your X67C IceMachine can separate

those fish from the bottom with a remarkable Split Zoom display mode.

In this mode, the right half of the flasher screen operates normally with

the surface at the 12 o'clock position and the bottom of the depth range

at the 6 o'clock position. The left half of the flasher zooms in on the six

feet just above the bottom, with the bottom at the 6 o'clock position and

6 feet above the bottom at the 12 o'clock position.

To switch to Split Zoom:

1. From a flasher page, press MENU|↓to FLASHER OPTIONS|ENT.

2. Press ENT|↓to SPLIT ZOOM|ENT.

3. Press EXIT|EXIT to return to the flasher page.

4. To return to normal mode, repeat these steps, but in step 2, select

Normal instead of Split zoom

At left, Flasher Page Menu with Flasher Options command high-

lighted. Center, Flasher Options Menu with Flasher Display Mode se-

lected. At right, the Split Zoom option has been selected.

The following figure show the bottom target separation possible using

the flasher's Split Zoom.

Notice the bottom target separation with Split Zoom mode.

Color Modes

Sonar Color Mode is described in detail in the manual on page 59. The

additional ice fishing features have increased the number of options

and how the color modes are controlled while using either the Flasher

or Ice Flasher.

There are six color mode options for the flasher pages, and seven for the

sonar chart page. The Ice Flasher default color is the IceView mode, but

other settings may suit your eyes better.

For example, some of our fishing friends favor the striking green-on-

black contrast of the Nightview mode…they use it a lot, even in broad

daylight! Experiment with the color modes to see which ones work best

for you under various fishing and lighting conditions.

To change the Flasher or Ice Flasher page color scheme:

1. From a flasher page, press MENU|↓to FLASHER OPTIONS|ENT.

2. Press ↓to FLASHER COLOR MODE|ENT.

Bottom ColorLine

Fish signal 2

zoomed,

about 3.5

feet above

the bottom.

Bottom ColorLine

Fish signal 2

Normal range side

Bottom zoom side

Fish signal 1

zoomed

Fish signal 1

This scale shows 6

feet above the bottom

Depth range

60 feet

3. Press ↑or ↓to Mode Name|ENT.

4. Press EXIT|EXIT to return to the flasher page.

At left, Ice Flasher menu with Flasher Options selected. Center,

Flasher Options menu with Flasher Color Mode selected. At right,

Nightview color option is selected.

Scouting Through the Ice

Since the 1960s, Lowrance flasher sonars have helped anglers hunt fish

beneath the ice without drilling holes. That's because your IceMachine

works as well through ice as it does through water!

This technique works best early in the winter fishing season, when ice

is clear and free of bubble formation. There must also be wet, bubble-

free contact between the transducer and the ice.

To shoot through solid ice, first brush away any snow from the spot you

want to search. Then, pour a small amount of non-toxic recreational

vehicle antifreeze onto the surface and place the transducer (face down)

in the puddle.

Another variation used by some anglers requires a small plastic bag,

such as a food storage bag. They fill the bag with a mixture of RV anti-

freeze and water. The bag is placed on the ice surface, and the trans-

ducer is rested in the "puddle" just as your head rests on a pillow.

Andere Handbücher für X67C

Inhaltsverzeichnis

Andere Lowrance Sonar Handbücher

Lowrance

Lowrance HOOK2 Bedienungsanleitung

Lowrance

Lowrance X-28 Bedienungsanleitung

Lowrance

Lowrance StructureScan HD Bedienungsanleitung

Lowrance

Lowrance HOOK-3x Bedienungsanleitung

Lowrance

Lowrance Elite-3x DSI Bedienungsanleitung

Lowrance

Lowrance Elite 5 Bedienungsanleitung

Lowrance

Lowrance X-15B Bedienungsanleitung

Lowrance

Lowrance HOOK-3x Bedienungsanleitung

Lowrance

Lowrance X-29 Bedienungsanleitung

Lowrance

Lowrance X-70A 3D Technisches Handbuch

Lowrance

Lowrance X-65 Bedienungsanleitung

Lowrance

Lowrance HOOK2 X series Bedienungsanleitung

Lowrance

Lowrance Elite-5x HDI Bedienungsanleitung

Lowrance

Lowrance X50 DS Bedienungsanleitung

Lowrance

Lowrance LMS-527cDF iGPS Bedienungsanleitung

Lowrance

Lowrance HDS-5x Bedienungsanleitung

Lowrance

Lowrance Elite 5 Sonar/GPS Bedienungsanleitung

Lowrance

Lowrance X96 Bedienungsanleitung

Lowrance

Lowrance Traditional Bedienungsanleitung

Lowrance

Lowrance X-40 Bedienungsanleitung

Lowrance

Lowrance Mark-4 HDI Bedienungsanleitung

Lowrance

Lowrance X91 Bedienungsanleitung

Lowrance

Lowrance Elite-5x HDI Bedienungsanleitung

Lowrance

Lowrance X125 Bedienungsanleitung

Beliebte Sonar Handbücher anderer Marken

Furuno

Furuno CSH-8L Bedienungsanleitung

Furuno

Furuno CSH-83 Bedienungsanleitung

Kongsberg

Kongsberg Simrad SP90 Series Bedienungsanleitung

Eagle

Eagle TriFinder 2 Bedienungsanleitung

Furuno

Furuno FSV-35 Bedienungsanleitung

Furuno

Furuno FSV-75 Bedienungsanleitung

Simrad

Simrad EQ 55 Bedienungsanleitung

Teledyne

Teledyne BlueView BV3200 Bedienungsanleitung

Reson

Reson SeaBat 7125 SV2 Bedienungsanleitung

Eagle

Eagle 101 Bedienungsanleitung

Furuno

Furuno MF-220 Bedienungsanleitung

IMAGENEX

IMAGENEX 881A-GS Bedienungsanleitung

Furuno

Furuno FSV-75 Bedienungsanleitung

Eagle

Eagle Z-15 Bedienungsanleitung

Simrad

Simrad SH80 - REV C Bedienungsanleitung

Simrad

Simrad ST90 Bedienungsanleitung

Hawk

Hawk Sultan Bedienungsanleitung

Kongsberg

Kongsberg Flexview Bedienungsanleitung