(16). All the channel LEDʼs will ash indicating the command
registered.
4. To exit this function press the CHASE BUTTON (24).
Assign Add/Kill: This function allows you to override a chase and turn
a single or a group of channels on. Channels are assigned to the FLASH
BUTTON (1 & 13), allowing to have a total of 16 programmed overrides.
You may use your overrides at different times and may use more than
one at a time. You can set this function to blackout (“KILL”) the chase, so
only your override channels come on. You may also, set this function to
“ADD” to the chase. When you “ADD,” your override channels will come
on as your chase is running. This function will operate in any chase. This
will be a momentarily function and your chase return to normal as soon as
release the FLASH BUTTON (1 & 13).
To program in an override:
1.Hold down the ASSIGN BUTTON (25) for two seconds until the
red assign LED come on and “AS” is displayed in the LCD
Display (6).
2. While holding down the SHIFT BUTTON (16), use the PATTERN
UP BUTTON (18) to selected “ASSIGN ADD.” ASSIGN ADD will be
indicated by a red LED above the PATTERN UP BUTTON (18).
3. Turn on any channels you wish to assign to a FLASH BANK.
4. After you have turned on your desired channels, press on of the
FLASH BUTTONS (1 &13) while holding down the ASSIGN
BUTTON (25). ALL the channel LED will ash indicating that your
program was placed into that FLASH BUTTONʼs memory.
Recalling an ASSIGN PATTERN:
1. You may recall your assign pattern in any chase function.
2.To add to the chase be sure the yellow LED next to the ADD/KILL
(17) is off and the red ASSIGN ADD LED is on. Simply press the
FLASH BUTTON (1 & 13) that stores the scene you wish to recall.
Youʼll notice that the chase remains running and your scene turns
on. You may recall (ADD) several scenes at once, by pressing as
many FLASH BUTTON (1 & 13) as you like at one time.
3. To blackout (KILL) the chase and just turn on your programmed
scene, press the ADD/KILL BUTTON (17) to turn on the yellow LED.
Be sure you are in ASSIGN KILL mode. Press the FLASH BUTTON
(1 & 13) that store the scene you wish to recall. Youʼll notice that the
chase stops and your scene comes on.
4. For both “ADD” and “KILL” the scene will remain on as long as
hold the FLASH BUTTON (1 & 13) down. Also you may turn several
ASSIGNS on at once.
Blind Function: This functions allow you to blackout (BLIND) specic
channels from your chase programs. To BLIND a channel be sure you are
in chase mode and:
1. While holding down the SHIFT BUTTON (16) press and release the
BLIND BUTTON (21) to activate the blind function.
2. While holding down the SHIFT BUTTON (16) press and release the
FLASH BUTTON (1 & 13) that corresponds to channel you wish to
remove from the chase.
3. You may repeat this process to blind as may channels as you like.
4. To remove a channel simply reverse the process, hold down the
SHIFT BUTTON (16) and press and release the FLASH BUTTON (1
& 13) that correspond to channel you wish to return to the chase.
5. To cancel the BLIND FUNCTION hold down the SHIFT BUTTON
(16), press and release the BLIND BUTTON (21). This will disable
the blind function.
Patch Settings: This function allows you to overlap DMX channels
together, giving you up to 96 DMX channels to work with. This function
is useful if you would like several channels on one DMX pack to turn at
once. For example, say you have a 4 channel DMX pack with 5 amps
maximum load per a channel and you want to turn on four 500 watt
lamps on DMX channel one. Your DMX pack is automatically going to
assign one 4 DMX channels to your pack one for one. To reduce the risk
of constantly blowing your pack you can plug each lamp into all four (4)
of your packs channels. Then you can patch these channels to be trig-
gered all at once. Since each of the 16 channels of the Light Station™
represent a DMX channel you would only have 16 to work with. How-
ever, if you patch your DMX channels, you could have a maximum of six
DMX channels triggered per a channel on the controller. So, you could
tell your controller to trigger DMX channels 1-4 by slider 1 on the board.
This would then activate all four channels on your DMX pack, allowing
all four lamps to be turned on at once, therefore eliminating the possibil-
ity of blowing you pack channels due to excessive load per a channel,
©LSC Suply® www.lightstreamcontrols.com Light Stantion Instruction Manual Page 13 ©LSC Suply® www.lightstreamcontrols.com Light Stantion Instruction Manual Page 14
Light Station™ Operating Instructions Light Station™ Operating Instructions
