Lucent Technologies CIB 3000 Bedienungsanleitung

CIB 3000

34-Button Deluxe Voice Terminal

CIB 3000

Comcode 103-972-972

Issue 2

CIB 3000

34-Button Deluxe Voice Terminal

The 34-button voice terminal (Figure 1) allows access to intercom and

outside lines as well as to programmable and other button features that

may be provided in your communications system. By attaching a voice

terminal power supply, you can also plug in a Hands-Free Unit or other

adjunct to this voice terminal. The lights by each programmable button

make this voice terminal useful as an attendant console in a small busi-

ness system.

FIGURE 1 34-Button Deluxe Voice Terminal

iss 2, cib3000-1

ASSEMBLING YOUR VOICE TERMINAL

Unpack your voice terminal, which has the following components:

●

voice terminal body

●

handset (with handset cord attached)

●

modular voice terminal cord

●

adjustable desk stand.

The desk stand provides three positions for the 34-button deluxe voice

terminal: 8 degrees (low), 18 degrees (middle), and 28 degrees (high).

Desk Stand Installation

NOTE: To avoid pinching your fingers, be sure the adjustable portion of

the desk stand is in the low position before installing the voice terminal.

(See Step 9.)

Turn the voice terminal over.

2Position the stand on the back of the voice terminal so that the voice

terminal mounting tabs fit into the “A” mounting slots on the stand

(Figure 2).

“A” Mounting Slots

“B” Mounting Slots 34-Button Voice Terminal

(Back View)

FIGURE 2 34-Button Deluxe Voice Terminal and Adjustable Desk Stand

3Gently slide the stand upward so that voice terminal tabs fit firmly into

the smaller part of the three mounting slots (Figure 3).

iss 2, cib3000-2

FIGURE 3 34-Button Deluxe Voice Terminal with Adjustable Desk Stand Attached

(Bottom View)

Thread one end of a (D8W) modular voice terminal cord between the

base of the desk stand and the bottom of the voice terminal and plug

it into the jack labeled LINE on the voice terminal.

Check to see that one end of the handset cord is attached to the

handset. If it is not, plug one end into the handset now.

Plug the other end of the handset cord into the jack on the lower right

of the voice terminal.

Turn the voice terminal right side up and place the handset in the cra-

dle (Figure 4).

iss 2, cib3000-3

Desk

Support

Base

FIGURE 4 34-Button Deluxe Voice Terminal Attached to the Desk Stand

8Plug the other end of the modular voice terminal cord into the build-

ing wiring connection, which may be a modular voice terminal exten-

sion cord or a modular voice terminal jack (Figure 5).

Modular Voice Terminal

Extension Cord

Modular Voice

Terminal Jack

FIGURE 5 Attaching the Voice Terminal Cord to Building Wiring

iss 2, cib3000-4

9The angle of the desk stand can be adjusted (Figure 6) by performing

the following:

●Use your left hand to hold the base of the stand firmly to the desk

top.

●To raise the voice terminal, use your right hand to lift slowly on

the rear of the voice terminal until the desired position is reached.

●To lower the voice terminal, use your right hand to lift the voice

terminal to release the locking tension. With the thumb of your

left hand, carefully press the side lever and allow the stand to

lower to the desired position.

FIGURE 6 Adjusting the 34-Button Deluxe Voice Terminal Desk Stand

REMOVAL

1To remove the stand from the 34-button deluxe voice terminal,

unplug the handset cord. Set the handset aside and turn the voice

terminal over. Unplug the modular voice terminal cord. Adjust the

desk stand to the low position and slide the stand down and away

from the voice terminal.

iss 2, cib3000-5

TESTING YOUR VOICE TERMINAL

Use the test/program (T/P) switch on the left side of the voice terminal to

test the lights and ringer. Slide the T/P switch away from you to the T

position (Figure 7). If the voice terminal is working properly, the red and

green lights will flash and the set will ring. If this does not happen, refer

to the “TROUBLESHOOTING TABLES” in your system’s Installation

Guide. If the problem is not resolved after troubleshooting your system,

contact your equipment supplier.

FIGURE 7 T/P Switch and Volume Control

SETTING THE VOLUME

The volume control switch is also located on the left side of the voice ter-

minal (Figure 7) and changes the volume of the alerting rings, speaker,

and button clicks.

Slide the switch away from you to increase the volume.

●

●Slide the switch towards you to decrease the volume.

iss 2, cib3000-6

REMOVING AND INSERTING LABELS

REMOVING

1Grasp the silver tab above the touch-sensitive buttons and pull the

labels out of the label slot (Figure 8).

INSERTING

1Insert the bottom of the label into the label slot above the column of

touch-sensitive buttons (Figure 8).

2Slide the label all the way into the slot until the appropriate label is

over the proper button.

FIGURE 8 Removing and Inserting Button Labels

To order more label strips, call the toll-free number for the National Parts

Sales Center: 1-800-222-PART. The part number (Comcode) is

844030809. These labels come in packages of 25 and can also be used

with 34- and 10-button voice terminals.

iss 2, cib3000-7

HANDSETS FOR THE HEARING IMPAIRED AND NOISY

LOCATIONS

All voice terminals come with a handset that is hearing-aid compatible.

Two other types of handsets are also available:

●The (R6C3) impaired-hearing handset (31753) has an extra amplifier

to provide greater volume in the earpiece. A thumbwheel volume on

the handset allows the volume to be turned up or down, as needed.

●The (R8C3) push-to-listen handset (31754) is for use in noisy loca-

tions. Like the impaired-hearing handset, the push-to-listen handset

has an extra amplifier and a thumbwheel volume control. It also has

a pushbutton on the handset that increases the volume in the ear-

piece and mutes background noise transmitted through the mouth-

piece.

iss 2, cib3000-8

Inhaltsverzeichnis

Andere Lucent Technologies Touch-Terminal Handbücher

Lucent Technologies

Lucent Technologies SLC 5 Series Bedienungsanleitung

Lucent Technologies

Lucent Technologies CIB 3023 Bedienungsanleitung

Lucent Technologies

Lucent Technologies SLC-2000 Access System Central Office... Bedienungsanleitung

Lucent Technologies

Lucent Technologies SLC-2000 Access System Central Office... Bedienungsanleitung

Lucent Technologies

Lucent Technologies Mitel SX200D Series Bedienungsanleitung

Lucent Technologies

Lucent Technologies CIB 7102 Bedienungsanleitung

Lucent Technologies

Lucent Technologies MLC-5 Bedienungsanleitung

Lucent Technologies

Lucent Technologies 8528T Bedienungsanleitung

Lucent Technologies

Lucent Technologies Definity 8434DX Bedienungsanleitung

Lucent Technologies

Lucent Technologies CIB 2853 Bedienungsanleitung

Lucent Technologies

Lucent Technologies Definity 8510T Bedienungsanleitung

Lucent Technologies

Lucent Technologies Merlin Magix Bedienungsanleitung

Lucent Technologies

Lucent Technologies Voice Terminal 8434DX Bedienungsanleitung

Lucent Technologies

Lucent Technologies 8400 Series Bedienungsanleitung

Lucent Technologies

Lucent Technologies 8400 Series Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung

Prestel

Prestel VCS-G2PRO Bedienungsanleitung