LUCOLED Lucoflex Bedienungsanleitung
Welcome to Lucoflex Lighting
Lucoflex Lighting is easy to install in straight, horizontal curved spaces where humidity or outdoor conditions.
It’s creates hot-pot free, smooth, warm and relaxing environments or delivers bright task lighting.
Please read these guidelines completely before installing.
It is important to read these guidelines completely to understand how it can be configured, cut to size, re-connected, and installed
so you can design your LED lighting layout.
Lucoflex
INSTALLATION GUIDE WET
LOCATION
DC
ONLY
1
Unpacking
Rolling the wheel when you unpacking the light.
Warning: Do NOT shake the light!
Do NOT pull the light from the wheel straightly.
No Twisting
Lucoflex is NOT allow to twisted in any conditions. The electrical circuit or
LED chips could be damaged with this action.
Bending
Lucoflex can only be bent laterally
(opposite bent along to light surface).
Do not bend smaller than allowed min bend dia.
The electrical circuit or LED chips could be damaged if bending
diameter is too small.
Min:
Φ50mm
[1.97]
Lucoflex is NOT allow to bending in up and down way.
The bending as photos show will damage the electrical circuit or LED chips
damaged seriously by this incorrect action.
Incorrect Bending
NEVER attempt any work without shutting off the electricity.
Do not stare directly into the LED lights when illuminated
Use only with low voltage 24V DC power source
Do not power LED tape while coiled on reel
Always observe polarity for connections, positive (+) to positive and negative (–) to negative
To be installed by a qualified electrician.
Keep away from combustible materials such as plastic or paper products.
All wiring must be in accordance with national and local electrical codes, low voltage Class 2 circuit.
If you are unclear as to how to install and wire this product, contact a qualified professional.
Up
Up
Horizontal line
Horizontal line
Down
Down
Horizontal line
Lucoflex
INSTALLATION GUIDE WET
LOCATION
DC
ONLY
2
INPUT CABLE AND END CAPS INSTALLATION
RE-CONNECTION
Lucoflex’s cuttable length in each 5cm.
Use the Ratcheting Cutter to cut the Lucoflex wherever a
Laser marked Scissors.
Please keep a sharp and clean edge.
CUTTING
Remove the Silicone
Use the knifte to carefully remove the Silicone
on the top. Scrape ligthly on the copper pads to
make sure there is no glue left. If any glue is
left, it will be difficult to solder the cables.
Found the mark side by laser in [Pin This Side].
Inset the gold coated Pin to the 2 cut light end. Make sure the Pin touch the copper pads
well. There is one set of the straight joiner kit included in each package in 15m. [shortger
length is offering separatly]
Fill the Crocodile cap full way with glue. Make sure there is no blank spaces.
Close the cap by pushing 2 sides together, make sure the teeth on the buttom bite well.
Input Cable Soldering
Add a small round puddle of solder on the top of
two copper pads.
Solder a positive and negative cable to
the positive and negative solder pads.
Seal End Cap
Take the end cap and fill it half way with glue. Insert
the cap on the end of the Lucoflex until the inner
back wall of the end cap is touching the end of the
light. Seal the edge of the end caps if there is any
blank spaces.
Wipe the left over glue around the end cap on a
paper towel.
Remark:
If no further modifications to the strip are necessary,
then the light needs to dry before installation.
We recommend at least 24 hours of drying time to
ensure the glue fully cures.
Andere LUCOLED Beleuchtungsausrüstung Handbücher
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
