LumiGrow smartPAR Pro 650e Datenblatt
Thank you for choosing LumiGrow as your preferred LED lighting solution! Committed to providing
the industry’s best customer service, the LumiGrow customer support team is always only a call or
click away.
To contact LumiGrow support, visit www.lumigrow.com/support or call (800) 514-0487
Installation Quick Start Guide
Certications
Smart Horticultural Lighting
smartPARTM
Light Sensor
Module
Safety Warning and Warranty Precautions
Turn off all AC power to light xture and wait 30 seconds before connecting or
removing smartPARTM modules. Failure to do so may damage the smartPARTM
module/xture, and void the warranty.
• Never immerse the module in water.
• Never spray or fog the module with chemicals/fertilizers.
• Never clean with a high-pressure jet system of any type.
• The smartPAR DB-9 port is for use with LumiGrow smartPARTM modules only. Plugging in any other
devices could damage the xture and void the warranty.
• See details of the warranty at www.lumigrow.com
©2017. LumiGrow, Inc. All right reserved. | PN #810-00028
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
WARNING: Turn o all AC power to light xture and wait 30 seconds before connecting or removing
smartPARTM modules. Failure to do so may damage the smartPARTM module/xture, and void the warranty.
Getting Started
Disposal Instructions
1. Turn o all AC power.
2. Carefully remove the dust cover over the DB-9
connector. A small screwdriver may be helpful.
3. Orient the two DB-9 connectors so that they line up
properly, and carefully insert the smartPARTM module.
The module has two broaching fasteners that lock
in place when the module is fully inserted. When
fully inserted, there should be no gap between the
smartPARTM module and xture.
4. Remove the adhesive backing from the underside of the
smartPARTM light sensor module and press the light sensor
onto the top of the xture . ** NOTE – the adhesive is
extremely strong and is single use only. Once the light
sensor is axed to the xture, it cannot be repositioned.
Hang your LumiGrow Pro Series E xture at the appropriate
height and spacing for your particular facility, or as specied
by a LumiGrow representative.
5. Hang the xtures according to the xture
installation guide that came with your xtures.
6. Power on AC mains. It may take a few minutes
for the xtures to connect to the network and
then turn on.
7. Log on to www.smartpar.lumigrow.com to
program the xtures and use the smartPARTM
light sensor. More details are at www.lumigrow.
com. Contact your LumiGrow representative
for additional assistance.
For additional information, visit www.lumigrow.com/support PN #810-00028
Contact your local waste management company or the nearest collection site to dispose of Electrical
and Electronic Equipment waste, per local and state requirements
Inhaltsverzeichnis
Andere LumiGrow Steuereinheit Handbücher
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
