Luminar EVERYDAY 59250 Montageanleitung

Visit our website at: http://www.harborfreight.com

Email our technical support at: [email protected]

Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the

back of the manual near the assembly diagram (or month and year of purchase if product has no number).

Keep this manual and the receipt in a safe and dry place for future reference. 22b

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-888-866-5797 as soon as possible.

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

Page 2 For technical questions, please call 1-888-866-5797. Item 59250

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that

follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Addresses practices not related to personal injury.

IMPORTANT SAFETY INFORMATION

To reduce the risk of FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS:

1. Install only according to these instructions.

Improper installation can create hazards.

2. Avoid electric shock. Keep plugs and receptacles

dry. Use only on GFCI-protected circuits.

3. Suitable for damp locations.

4. This product is not suitable for recessed

installation in ceilings or on buildings. Do

not install on radiant heat ceilings.

5. Wear ANSI-approved goggles and heavy-

duty work gloves during installation.

6. Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

7. Do not operate the Light in explosive atmospheres,

such as in the presence of flammable liquids,

gases or dust. The Light generates sparks

which may ignite the dust or fumes.

8. The Light’s plug must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with the Light. Unmodified plugs and

matching outlets will reduce risk of electric shock.

9. Do not abuse the Power Cord. Never use the Cord

for unplugging the Light. Keep cord away from

heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

10. Maintain the Light. Check for breakage of

parts and any other condition that may affect

the Light’s operation. If damaged, have it

repaired before use. Many accidents are

caused by poorly maintained items.

11. Maintain labels and nameplates on the

Light. These carry important safety

information. If unreadable or missing, contact

Harbor Freight Tools for a replacement.

12. This product is not a toy. Keep it

out of reach of children.

13. Do not install directly over a heat source (stove, etc.).

14. People with pacemakers should consult their

physician(s) before use. Electromagnetic fields in

close proximity to heart pacemaker could cause

pacemaker interference or pacemaker failure.

15. The warnings, precautions, and instructions

discussed in this instruction manual cannot

cover all possible conditions and situations

that may occur. It must be understood by the

operator that common sense and caution are

factors which cannot be built into this product,

but must be supplied by the operator.

SAVE THESE INSTRUCTIONS.

Page 3For technical questions, please call 1-888-866-5797.Item 59250

Grounding

TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING

WIRE CONNECTION:

Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.

Do not modify the power cord plug provided with the Light. Never remove the grounding prong

from the plug. Do not use the Light if the power cord or plug is damaged. If damaged, have it repaired by a

service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a

qualified electrician.

110-120 VAC Double Insulated Lights: Lights with Two Prong Plugs

Outlets for 2-Prong Plug

1. To reduce the risk of electric shock, double

insulated equipment has a polarized plug

(one blade is wider than the other). This plug will fit

in a polarized outlet only one way. If the plug does

not fit fully in the outlet, reverse the plug. If it still

does not fit, contact a qualified electrician to install

the proper outlet. Do not change the plug in any way.

2. Double insulated tools may be used in either of the

120 volt outlets shown in the preceding illustration.

(See Outlets for 2-Prong Plug.)

Extension Cords

1. Grounded Lights require a three-

wire extension cord. Double Insulated Lights can

use either a two or three wire extension cord.

2. As the distance from the supply outlet increases,

you must use a heavier gauge extension cord.

Using extension cords with inadequately sized wire

causes a serious drop in voltage, resulting in loss of

power and possible tool damage. (See Table A.)

3. The smaller the gauge number of the wire,

the greater the capacity of the cord. For

example, a 14 gauge cord can carry a

higher current than a 16 gauge cord.

4. When using more than one extension cord to

make up the total length, make sure each cord

contains at least the minimum wire size required.

5. If you are using one extension cord for more than

one tool, add the nameplate amperes and use the

sum to determine the required minimum cord size.

6. If you are using an extension cord outdoors, make

sure it is marked with the suffix “W-A” (“W” in

Canada) to indicate it is acceptable for outdoor use.

7. Make sure the extension cord is properly wired

and in good electrical condition. Always replace

a damaged extension cord or have it repaired

by a qualified electrician before using it.

8. Protect the extension cords from sharp objects,

excessive heat, and damp or wet areas.

TABLE A: RECOMMENDED

MINIMUM WIRE GAUGE FOR

EXTENSION CORDS* (120 VOLT)

NAMEPLATE

AMPERES

(at full load)

EXTENSION CORD

LENGTH

25´ 50´ 75´ 100´ 150´

0 – 2.0 18 18 18 18 16

2.1 – 3.4 18 18 18 16 14

3.5 – 5.0 18 18 16 14 12

5.1 – 7.0 18 16 14 12 12

7.1 – 12.0 16 14 12 10 -

12.1 – 16.0 14 12 10 - -

16.1 – 20.0 12 10 - - -

* Based on limiting the line voltage drop to five volts at

150% of the rated amperes.

Page 4 For technical questions, please call 1-888-866-5797. Item 59250

Symbology

Double Insulated

VAC Volts Alternating Current

AAmperes

WARNING marking concerning Risk

of Eye Injury. Wear ANSI-approved

safety goggles with side shields.

Read the manual before

set-up and/or use.

WARNING marking

concerning Risk of Fire.

Do not cover ventilation ducts.

Keep flammable objects away.

WARNING marking concerning

Risk of Electric Shock.

Properly connect power cord

to appropriate outlet.

Specifications

Electrical Rating 120 VAC / 60Hz / 19W / 0.172A

Receptacle Load 1.8A

Power Cord Length 5 ft.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Page 5For technical questions, please call 1-888-866-5797.Item 59250

Mounting Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document

including all text under subheadings therein before set up or use of this product.

Suspended Mounting

1. Select a suitable location for hanging the

Grow Light. The Grow Light must be hung

from a sturdy mounting surface able to

support the weight of the fixture.

CAUTION! Do not install the Grow Light into drywall.

WARNING! TO PREVENT SERIOUS INJURY:

Verify that installation surface has no hidden

utility lines before drilling or driving screws.

2. Mark mounting locations 23.6″

apart on mounting surface.

23.6"

3. Drill 1/8″holes in mounting locations.

4. Thread J Hooks into holes.

5. Add chains to V Hooks.

6. Attach V Hooks to Grow Light.

7. Hang the Chain on the J Hook.

8. Connect no more than eight Grow Lights together.

9. Plug power cord into 120VAC grounded

receptacle. Turn on Power Switch(es).

Page 6 For technical questions, please call 1-888-866-5797. Item 59250

Surface Mounting

1. Mark mounting locations 22.6″

apart on mounting surface.

2. Drill 1/8″holes in mounting locations.

3. Thread Screws into holes, leaving Screw heads

extending 0.1″from mounting surface.

4. Align large ends of keyholes on Grow Light

with Screws on mounting surface.

5. Slide Grow Light toward small

ends of keyholes to secure.

Keyhole

6. Connect no more than eight Grow Lights together.

7. Plug power cord into 120VAC grounded

receptacle. Turn on Power Switch(es).

Maintenance

Procedures not specifically explained in this manual must

be performed only by a qualified technician

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:

Unplug the Light from its electrical outlet before performing any procedure in this section.

TO PREVENT SERIOUS INJURY FROM LIGHT FAILURE:

Do not use damaged equipment. If damage is noted, have the problem corrected before further use.

1. BEFORE EACH USE, inspect the general

condition of the Grow Light. Check for:

• loose hardware

• misalignment or binding of moving parts

• damaged cord/electrical wiring

• cracked or broken parts

• any other condition that may

affect its safe operation.

2. PERIODICALLY, clean the Diffuser Cover with

nonabrasive glass cleaner and a clean cloth.

WARNING! TO PREVENT SERIOUS INJURY: If

the supply cord of this light is damaged, it must be

replaced only by a qualified service technician.

Page 7For technical questions, please call 1-888-866-5797.Item 59250

Parts List and Diagram

Part Description Qty

1 Triangle V Hook 2

2 Chain 2

3 J Hook 2

4 Screw 2

5 Grow Light 1

1234

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only, and are not available

individually as replacement parts. Specify UPC 193175463784 when ordering parts.

26677 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,

and warrants to the original purchaser that this product is free from defects in materials and workmanship for the

period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,

to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper

installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries

to persons or property, or for incidental, contingent, special or consequential damages arising from the use of

our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges

prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.

If our inspection verifies the defect, we will either repair or replace the product at our election or we may

elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will

return repaired products at our expense, but if we determine there is no defect, or that the defect resulted

from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Inhaltsverzeichnis

Andere Luminar Beleuchtungsausrüstung Handbücher

Luminar

Luminar 66439 Montageanleitung

Luminar

Luminar 64398 Montageanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung