luminii Bosca BOS C Series Bedienungsanleitung
Installation Instructions for Bosca
Models BOS-XX-C-XX, & BOS-XX-S-XX
REV0.5 07272018*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Instruction page index:
Bosca clip-in mount
or Bosca magnetic
Bosca screw-in mount
Page 1 of 6
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
E472444
Bosca adjustable hinge mounting
Clip-in installation
Screw-in installation
Magnetic installation
Adjustable hinge mounting installation
Power feed layout guide
2
3
4
5
6
Bosca - Installation Instructions
Please read all instructions prior to installation and keep for future reference!
Models BOS-XX-C-XX
Page 2 of 6
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR DAMP LOCATIONS
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. INHERENTLY PROTECTED
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
4.1 Connect +24 VDC red wire from the fixture to the power supply
+24 VDC red wire with a wire nut. Connect -24VDC black wire
from the fixture to power supply -24VDC black wire with a wire
nut.
4
class II
power
supply
24 VDC
120 VAC
4.1
to fixture
+24 VDC RED
-24 VDC BLACK -24 VDC BLACK
+24 VDC RED
Note: Refer to the power supply installation instruction for
additional information.
Note: More than one person is recommended for this
installation.
1
1.1 Carefully remove the mounting channel from the back of the
fixture. Mounting channel is 1/2" shorter than the fixture for
wire management.
2.1 Determine the location of the fixture. Then secure the mounting
channel to the surface with the provided mounting screws. When
installing the mounting channel take into consideration the 1/2"
shorter per wire lead/connector.
2.2 Install mounting screws every 6 inches to the center of the mounting
channel.
1.1
2
mounting channel
fixture
lead wires
screw
mounting channel
2.1
screw
3
Option 2- Feed wire whip to the power supply.
OR
3.1 Follow connector dimensions below and drill hole through surface.
Insert wire lead/connector through surface & snap fixture into the
mounting channel to secure in place. Option 1- Secure female quick connect to
male quick connect. Feed male quick connect
wire through conduit to power supply.
3.2 Follow one of the two options to connect the fixture to the
power supply.
female quick
connect
male quick
connect
to power supply
mounting
channel
fixture
wires from
fixture
wires from
fixture
3.1
3.2
3.2
Female quick
connect end
0.45"
Male quick
connect end
0.38"
Female/male
adapter
0.45"
Lead wire
end
0.20"
E472444
Clip-in installation
REV0.5 07272018*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Bosca - Installation Instructions
Please read all instructions prior to installation and keep for future reference!
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Models BOS-XX-S-XX
Page 3 of 6
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR DAMP LOCATIONS
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
Note: Prior to installation all 24VDC wires must be present
near fixture. Refer to the power supply installation instruction
for additional information.
Note: More than one person is recommended for this
installation.
2
2.1 Determine the location of the fixture. Then secure the fixture to the surface
using the provided mounting screws.
3
Option 2- Feed wire whip to the power supply.
OR
Option 1- Secure female quick connect to
male quick connect. Feed male quick connect
wire through conduit to power supply.
3.1 Follow one of the two options to connect the
fixture to the power supply.
female quick
connect
male quick
connect
to power supply
wires from
fixture
fixture
fixture
screw
4.1 Connect +24 VDC red wire from
the fixture to the power supply +24
VDC red wire with a wire nut.
Connect -24VDC black wire from the
fixture to power supply -24VDC
black wire with a wire nut.
4
class II
power
supply
24 VDC
120 VAC
+24 VDC RED
-24 VDC BLACK -24 VDC BLACK
+24 VDC RED
4.1
to fixture
wires from
fixture
E472444
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. INHERENTLY PROTECTED
2.1
2.1
1
1.1 Install brackets 4” from each end and 30” in between the fixtures. Line up each mounting bracket to the
back on the fixture & insert the edge of the clip into the fixture. Then rotate and push clip in until you feel
a click. Followed by tightening the set screw using the Allen wrench (provided). Repeat for the remaining
brackets.
1.1
1.1 1.1
completely installed
fixture
mounting
bracket
set screw
mounting bracket
Screw-in installation
REV0.5 07272018
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Note: Prior to installation all 24VDC wires must be present
near fixture. Refer to the power supply installation instruction
for additional information.
Note: More than one person is recommended for this
installation.
1
1.1 Determine the location of the fixture. Must be made of steel or a ferrous
metal. Clean the surface area thoroughly from any debris. Snap the fixture
onto the metal surface. If necessary fixture can easily be removed by
rotating off the surface and repositioning correctly.
fixture
fixture
3.1 Connect +24 VDC red wire from
the fixture to the power supply +24
VDC red wire with a wire nut.
Connect -24VDC black wire from the
fixture to power supply -24VDC
black wire with a wire nut.
3
class II
power
supply
24 VDC
120 VAC
+24 VDC RED
-24 VDC BLACK -24 VDC BLACK
+24 VDC RED
3.1
to fixture
2
Option 2- Feed wire whip to the power supply.
OR
Option 1- Secure female quick connect to
male quick connect. Feed male quick connect
wire through conduit to power supply.
2.1 Follow one of the two options to connect the
fixture to the power supply.
female quick
connect
male quick
connect
to power supply
wires from
fixture
wires from
fixture
metal backing
metal backing
1.1
1.1
Magnetic installation
REV0.5 07272018
Bosca - Installation Instructions
Please read all instructions prior to installation and keep for future reference!
Models BOS-XX-M-XX
Page 4 of 6
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR DAMP LOCATIONS
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
E472444
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. INHERENTLY PROTECTED
Please read all instructions prior to installation and keep for future reference!
Page 5 of 6
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
E472444
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SURFACE MOUNT ONLY
5. SUITABLE FOR WET LOCATIONS, MUST USE APPROPRIATE
WEATHERPROOF RATED WIRE CONNECTORS.
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. INHERENTLY PROTECTED
Adjustable hinge installation
Bosca Wet - Installation Instructions
Models BOSW-XX-AH-XX
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE REV0.5 07262018
1
1.1 Slightly loosen both screws on the sides of the hinge bracket.
Rotate the fixture to expose mounting hole.
mounting bracket
mounting
bracket
fixture mounting
hole
2
Note: Prior to installation all 24VDC wires must be present
near fixture. Refer to the power supply installation instruction
for additional information.
Note: More than one person is recommended for this
installation.
2.1 Determine the location of the fixture. Then secure the fixture to
the surface using the provided mounting screws.
2.2 Rotate the fixture to the desired angle then tighten the side
screws to secure.
1.1
2.1
2.1
4.1 Connect +24 VDC red wire from
the fixture to the power supply +24
VDC red wire with a wire nut.
Connect -24VDC black wire from the
fixture to power supply -24VDC
black wire with a wire nut.
4
class II
power
supply
24 VDC
120 VAC
+24 VDC RED
-24 VDC BLACK -24 VDC BLACK
+24 VDC RED
4.1
to fixture
screw
2
Option 2- Feed wire whip to the power supply.
OR
Option 1- Secure female quick connect to
male quick connect. Feed male quick connect
wire through conduit to power supply.
2.1 Follow one of the two options to connect the
fixture to the power supply.
female quick
connect
male quick
connect
to power supply
wires from
fixture
wires from
fixture
1.1
Bosca - Installation Instructions
Please read all instructions prior to installation and keep for future reference!
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Models BOS-XX-M-XX
Page 6 of 6
1. PRODUCT TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR DAMP LOCATIONS
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
E472444
5. SURFACE MOUNT ONLY
6. SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
7. INHERENTLY PROTECTED
power supplies at the
end of the run
power supplies in the
middle of the run
consecutive layout,
NOT RECOMMENDED
multiple powerfeed layouts
power supply
low voltage wires
fixture 1
fixture 1 fixture 2
low voltage wires
power supply
power supply
low voltage wires
fixture 1
power supply
low voltage wires
fixture 2
REV0.5 07272018
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere luminii Arbeitsleuchte Handbücher
Beliebte Arbeitsleuchte Handbücher anderer Marken
PowerSmith
PowerSmith PWLD080T Bedienungsanleitung
MaxLite
MaxLite 73683 Bedienungsanleitung
Heitronic
Heitronic Trend 27867 Bedienungsanleitung
Monzana
Monzana Gore MZCL10 Bedienungsanleitung
EINHELL
EINHELL TE-CL 18/2000 LiAC Bedienungsanleitung
Bayco
Bayco NIGHTSTICK Dual-Light Xtreme Lumens... Bedienungsanleitung