Lutron Electronics Centurion C-600 Bedienungsanleitung

Installation Instructions

Please Leave for Occupant

Incandescent Dimmers

C-600, C-1000, C-1500, C-2000

120VAC, 60Hz

Table Of Contents

Package Contents..................................................1

Important Notes......................................................1

Single Unit Installation ...........................................1

Multigang Installation-

No side Sections Removed .............................2

Multigang Installation-

Side Section Removed ....................................3

Installation Assistance ...........................................4

Important Notes

Please Read Before Installation

Install in accordance with national and local electrical

codes.

Lamp Type: Use this product with incandescent and

quartz lamps

only

--120VAC, 60Hz. Do

not

connect

to low-voltage lamps or any appliance.

Caution: To avoid overheating and possible

damage to other equipment, do not install to

control receptacles, fluorescent lighting fixtures,

motor-operated appliances, or transformer

supplied appliances.

Short Circuit Check: Check new installation for

short circuits prior to installation of dimmer by using a

single pole switch and connecting the appropriate

terminals to the hot wire and the lamp with power

OFF. Turn power on. If lights do not work, or

breaker trips, a short is present. Correct the wiring

and check circuit again. Install dimmer only when

short is no longer present.

Wire Connectors: Wire connectors provided can be

used to join one 10-, 12-, 14-, 16-, or 18-gauge wire

with one or two 12- or 14-gauge wires. Use them with

copper wire

only.

Package Contents:

Control

Mounting

Screws

Knob

Faceplate

Wire

Connectors

4.Push wires into switchbox, allowing room for

dimmer backbox to be inserted.

1/2" or 5/8"

Switchbox and Location: A single-gang switchbox

(3" high x 2" wide x 21/2" deep) will service all

individual Centurion dimmers. These dimmers are

designed to operate in ambient temperatures from

0°C to 40°C (32°F to 104°F). Allow a minimum

space of 41/2" above and below the dimmers for

proper heat dissipation.

Single Unit Installation

1. Turn power OFF at fusebox or circuit breaker.

Wiring with power on can result in personal injury.

Damage to product caused by wiring with power on

voids warranty.

2. Remove faceplate from dimmer to prevent

damage and to access mounting holes. Pull out at

top and bottom edges, plate will snap off.

3.Strip insulation from dimmer wires and from wires

to which dimmer is to be connected as follows:

• 1/2" for 10, 12, and 14 gauge wire

• 5/8" for 16 and 18 gauge wire

• Using the wire connectors provided, connect the

green or bare ground wire on the dimmer (if

present) to the green or bare copper ground wire in

the wallbox. Note: If a green or bare copper ground

wire is not in the wallbox, contact a licensed

electrician.

• Connect the 2 dimmer leads to the 2 wallbox leads

(see Figure A). The hot wire may be connected to

either of the dimmer wires. Be sure copper

conductor is not exposed.

Figure A. Switchbox Wiring

Ground

(Green or Bare)

5.Mount dimmer to switchbox using 2 screws

provided and center mounting holes. Unit

must

mounted vertically. See Figure B.

6.Check knob for correct positioning. Lutron

inscription on knob indicates light level. When

dimmer is off, knob is positioned as shown in Figure

B. If not, remove knob from the stem, align in the

correct position, and push securely back on.

7.Snap faceplate on. See Figure C.

8.Turn power ON. Turn knob clockwise to increase

light intensity; counterclockwise to decrease light

intensity and click off.

Figure B. Front View - Single Unit Installation

LUTRON

Center Mounting Holes

Offset Mounting Holes

Determine the number of switchboxes necessary

by using the Switchbox Requirement Chart (Table A).

When ganging any combination of small dimmers

(C-600, C-1000) and large dimmers (C-1500, C-2000),

keep all small together at one end of the gang and all

large dimmers together at the other end of the gang.

2. When ganging an even number of small controls

use gangable switchboxes with tapped ears. Do not

use plaster rings or gangbox covers. One switchbox

in addition to the total number of controls is required

in order to provide space for faceplates (e.g. 4

dimmers require 5 switchboxes). Place additional

switchboxes 3/4" apart from other switchbox to

provide space for faceplate(s). See Figure D.

3. Turn power OFF. Wire each dimmer according

to step 3 in "Single Unit Installation" on page 1.

4. Install controls in switchbox. Use center

mounting holes for first unit, then use offset mounting

holes as required for proper alignment (see Figure

E). Allow 1/32" between controls for ease in

attaching faceplates.

Multigang Installation-

No Side Sections Removed (No Derating Required)

In multigang installations several dimmers or controls

are grouped horizontally in one ganging switchbox or

in a series of connected switchboxes. Installation of

dimmers without removing side sections allows

operation at full capacity (no derating). Follow

instructions below. For retrofit installations side

sections can be removed to fit existing switchboxes.

This requires derating and is described in "Multigang

Installation - Side Sections Removed" on page 3.

Figure D. Switchbox Positioning Four-Gang Controls

Number of Small Controls

0123456

Number of Switchboxes Required

0 0 1 1+1* 4 4+1* 7 1+7*

Number 113568911

of Large 24679101213

Controls 3 6 8 10 11 13 14 16

4 9 11 12 14 15 17 18

Table A. Switchbox Requirement Chart

No Side Sections Removed

*See item #2

Single-Gang

Gangable

Switchbox

3/4" Space

(use chase

nipple)

Four-gang Gangable

Switchbox

Figure C. Snap on Faceplate

Press Plate Until Tabs Snap In

Faceplate

Tabs

Figure E. Front View - Four-Gang Installation

LUTRON LUTRON LUTRON LUTRON

Center Mounting Holes Offset Mounting Holes

3. Remove only inner side sections. Using pliers,

bend side sections as far as you can and then back

to their original positions. Repeat several times until

side sections break off (See Figure F).

Note:

Do not remove outer side sections of the two

dimmers which are on the ends of the gang.

Figure G. Cutting Faceplate

Side section break-off points

Figure G. Side Section Removal

5. Snap multiple single faceplates onto controls and

adjust up or down for a snug fit. See Figure F.

Figure F. Front View - Four-Gang Installation

Table B. Derating Chart - Maximum Wattage

Control No Sides 1 Side 2 Sides

Model Size Removed Removed Removed

C-600 S 600W 600W 500W

C-1000 S 1000W 900W 700W

C-1500 L 1500W 1250W 1000W

C-2000 L 2000W 1800W 1500W

Multigang Installation--

Side Sections Removed (Derating Required)

In multigang installations several dimmers or controls

are grouped horizontally in one ganging switchbox or

in a series of connected switchboxes.

1. Derating is necessary when side sections are

removed. Use Derating Chart (Table B) to determine

maximum wattage of lamps safely dimmed when side

sections are removed. Match the dimmer model

number and the number of side sections removed to

determine the maximum load that can be controlled.

Determine the number of switchboxes necessary

by using the Switchbox Requirement Chart (Table C).

When ganging any combination of small controls

(C-600, C-1000) and large dimmers (C-1500, C-2000),

place all small controls together at one end of the

gang and all large controls at the other end of the

gang.

4. Turn power OFF. Wire each dimmer according

to step 3 in "Single Unit Installation" on page 1.

5. Install controls in switchbox(es). Use center

mounting holes. (With large controls, you can use

offset mounting holes as required for proper

alignment). Allow 1/32" between controls for ease in

attaching faceplates.

6. Remove appropriate sides of faceplates to match

the side sections removed from the controls (see

Faceplate Cutting). Then snap multiple single

faceplates onto controls and adjust up or down for a

snug fit.

Number of Small Controls

0123456

Number of Switchboxes Required

0 0123456

Number 1 1345678

of Large 2 35678910

Controls 3 5789101112

4 7 9 1011121314

Table C. Switchbox Requirement Chart

Side Sections Removed

Faceplate Cutting

Some faceplates will need to be cut if removing side

sections of dimmers. Position faceplate on a soft

cloth face down. Press firmly and score the groove

on the back of faceplate with a razor-sharp knife,

using vertical side groove to keep knife on straight

course (see Figure G). Bend section back and forth

to break it off. Smooth edges by placing fine-grained

sandpaper on a flat surface and rub edge of the

faceplate over the sandpaper a few times. Hold

faceplate steady as you rub to keep a true edge.

LUTRON LUTRON LUTRON LUTRON

4Lutron Electronics Co., Inc.

7200 Suter Road

Coopersburg, PA 18036-1299

Made and printed in U.S.A. 7/99 P/N 030-088 Rev. C

WorldwideTechnical and Sales

Assistance

If you have questions concerning the installation or

operation of this product, call the

LutronTechnical

Assistance Hotline.

Please provide exact model

number when calling.

(800) 523-9466 (U.S.A., Canada, and the Caribbean)

Other countries call (610) 282-3800

Fax (610) 282-3090

Warranty

Lutron will, at its option, repair or replace any control that is defective in materials or

manufacture within one year after the purchase. For warranty service, return unit to

place of purchase or mail to Lutron at 7200 Suter Road, Coopersburg, PA 18036-1299,

postage prepaid.

This warranty is in lieu of all other warranties, express or implied, and the implied

warranty of merchantability is limited to one year from purchase. This warranty

does not cover the cost of installation, removal, or reinstallation, or damage

resulting from misuse, abuse, or improper wiring or installation.

This warranty gives you specific legal rights, and you may also have other rights which

vary from state to state. Some states do not allow the exclusion or limitation of

incidental or consequential damages or limitations on how long an implied warranty

may last, so the above limitations and exclusions may not apply to you.

Dieses Handbuch passt für folgende Modelle

Andere Lutron Electronics Dimmer Handbücher

Lutron Electronics

Lutron Electronics CGP2730 Bedienungsanleitung

Lutron Electronics

Lutron Electronics Caseta Bedienungsanleitung

Lutron Electronics

Lutron Electronics MACL-153M Bedienungsanleitung

Lutron Electronics

Lutron Electronics Maestro Wireless MRF2-600M Bedienerhandbuch

Lutron Electronics

Lutron Electronics ST-RD Bedienungsanleitung

Lutron Electronics

Lutron Electronics Energi TriPak Series Bedienerhandbuch

Lutron Electronics

Lutron Electronics Nova NF-10 Bedienungsanleitung

Lutron Electronics

Lutron Electronics Maestro Wireless MRF2-3PD Montage- und Bedienungsanleitung

Lutron Electronics

Lutron Electronics QOTO Q-600P Bedienungsanleitung

Lutron Electronics

Lutron Electronics Caseta Bedienungsanleitung

Lutron Electronics

Lutron Electronics Spacer System SPS-300LD Bedienungsanleitung

Lutron Electronics

Lutron Electronics Caseta Pico PD-6WCL Bedienungsanleitung

Lutron Electronics

Lutron Electronics Aurora Z3-1BRL Bedienungsanleitung

Lutron Electronics

Lutron Electronics MRFA-3LD-URC Bedienungsanleitung

Lutron Electronics

Lutron Electronics DESIGNER-STYLE WIRED MAESTRO DIMMERS Bedienungsanleitung

Lutron Electronics

Lutron Electronics Maestro MSCL-OP153M Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics VTELV-600M Bedienungsanleitung

Lutron Electronics

Lutron Electronics QSNE-4A-D Bedienungsanleitung

Lutron Electronics

Lutron Electronics HD-RD Bedienungsanleitung

Lutron Electronics

Lutron Electronics N-600 Bedienungsanleitung

Lutron Electronics

Lutron Electronics Hi-Lume Premier 0.1% Bedienungsanleitung

Lutron Electronics

Lutron Electronics PJ2-3BRL Bedienungsanleitung

Lutron Electronics

Lutron Electronics Homeworks RF Maestro HRD-6D Bedienungsanleitung

Beliebte Dimmer Handbücher anderer Marken

ZooZ

ZooZ ZEN54 LR Bedienungsanleitung

Lex

Lex 6KW Bedienungsanleitung

DIODE LED

DIODE LED TOUCHDIAL Mini Bedienungsanleitung

Viessmann

Viessmann 5590 Bedienungsanleitung

Teleco

Teleco TVSTICK868RGB29 Bedienungsanleitung

INSTEON

INSTEON LampLinc 2457D2 Bedienungsanleitung

LEGRAND

LEGRAND WattStopper RH703PTU Bedienungsanleitung

ADB

ADB EURODIM TWIN TECH Bedienungsanleitung

Sinope

Sinope DM2550ZB-C4 Bedienungsanleitung

SkyLink

SkyLink SK7 Bedienungsanleitung

Makel

Makel RC Bedienungsanleitung

Lightronics

Lightronics XC-62 Bedienungsanleitung

Triton Blue

Triton Blue DM-1225 Bedienungsanleitung

ETC

ETC ES750 Betriebsanleitung

NA OMEGA + Bedienungsanleitung

GE ZB3001 Bedienungsanleitung

LSC

LSC DP-1210 Bedienungsanleitung

Leviton

Leviton DDS8800 Betriebsanleitung