Lutron Electronics Sivoia QED Series Betriebsanleitung

Sivoia QED®

IR Remotes With

Favorite Preset

Button

Programming

Guide

Page 1

Sivoia QED®Favorite Preset Remote Programming Guide

The Sivoia QED IR Remote with Favorite Preset Button Programming Guide is a supplement to

the Sivoia QED Wiring and Programming Guide. This guide describes the programming and setup

of the three conﬁgurations of IR remotes that have a round silver favorite preset button.

The IR Remote can be used to program and control shades/drapes in the system via a drive unit

with an IR receiver, an IR Keypad or via the IR reciever in the Contact Closure Interface.

The following chart describes the programming steps. Most of the programming can be

performed from any of the three IR remotes. The Two Shade Group Remotes (Type C) require

additional programming to deﬁne the shades/drapes that are assigned to the two sub groups

that these can control.

Type A

Single Shade Group

with Favorite Preset

SVIT-SH-WH

SVIT-DR-WH

Type B

Shade and Lighting

with Favorite Preset

SVIT-GRX-DR-WH

SVIT-GRX-SH-WH

SVIT-MIR-SH-WH

SVIT-MIR-DR-WH

Type C

Two Shade Groups

with Favorite Preset

SVIT-SC-BL-WH

SVIT-SR-BL-WH

SVIT-SH-DR-WH

SVIT-SH-SH-WH

Step Description

Addressing System

Assigning Drives

to IR Remote

Master Group

Assigning Drives

to IR Remote

Sub Groups

N/A N/A

4 & 5

Storing and

Locking Presets

Individual Level

Adjust

P P P

IR Remote Programming Steps for IR Remotes with

Favorite Preset Button

GROUP 2

GROUP 1

Sivoia QED®Favorite Preset Remote Programming Guide

1.1

Addressing the system

Addressing can be done with type A, B, or C remotes.

Note: Prior to addressing the system, all shades/drapes, by default, will respond to all IR

Remotes. After addressing, shades/drapes will not respond to any remote until it is assigned to

an IR Receiver, IR Keypad or contact closure interface.

Page 2

Enter Programming Mode

Aim the Remote at the IR Receiver

and Press and Hold Open and

Close for 5 seconds. The LED’s

on the receiving device will ash

1.2 Enter Addressing Mode

Aim the Remote at the IR

Receiver and tap Open. The LED’s

on the drive will ash rapidly until

addressed. Addressing is

complete when the receiving

device starts ashing slowly.

The addressing process will take

approximately 1 minute.

1.3 Exit Addressing Mode

Aim the Remote at the IR Receiver

and Hold Open and Close for

5 seconds. The LED’s on the drive

will stop ashing.

(H) Press and hold button

(T) Tap button

Sivoia QED®Favorite Preset Remote Programming Guide

Page 3

2.1

Assigning Drives to the Master Shade Group

All three types of remotes (A, B and C) can be used to assign shades to the Master Shade Group.

However, all shades that are assigned to this group will only respond to the Type A and Type B

remotes after this step. Type C remote requires this step, in addition to step 3, to control

shades/drapes.

Enter Programming Mode

Aim the Remote at the IR Receiver

and Press and Hold Open and

Close buttons (Type A and B) or

both round silver buttons (Type C)

for 5 seconds. The LED’s on the

receiving device will ash

2.2 Enter Master Assignment Mode

Aim the Remote at the IR Receiver

and tap the Close button (Type

A and B) or while holding the

bottom round silver button, tap

close button (Type C). All

unassigned shades/drapes will

open and all assigned shades

drapes will close.

Assigning and Un-Assigning

Shades/Drapes

Select Shade/Drape to Assign

Aim the Remote at the IR Receiver

and tap the Close button until the

desired shade/drape is selected

(Tapping the Open button will

select shades/drapes in the

opposite order). Selected shade/

drape will “wiggle” or move back

and forth a few inches

continuously.

Assign Selected Shade/Drape

Aim the Remote at the IR Receiver

and tap the Lower button. The

wiggling shade/drape will close to

indicate it is assigned. A

Then

2.3

Page 4

Sivoia QED®Favorite Preset Remote Programming Guide

2.4 Exit Programming Mode

Aim the Remote at the IR Receiver

and Press and Hold Open and

Close buttons (Type A and B) or

both round silver buttons (Type C)

for 5 seconds. The LED’s on the

receiving device will ash. All

shades/drapes will return their

previous position.

Assigning Drives to the Master Shade Group

(continued)

Unassign Selected

Shade/Drape

Aim the Remote at the IR Receiver

and tap the Raise button. The

wiggling shade/drape will open

to indicate it is unassigned.

Assign All Shades/Drapes

Aim the Remote at the IR Receiver

and Press and Hold the Close

button for 5 seconds (Type A,B

and C). All shades/drapes will

close to indicate they are assigned.

Unassign All Shades/Drapes

Aim the Remote at the IR Receiver

and Press and Hold the Open

button for 5 seconds (Type A,B

and C). All shades/drapes will

open to indicate they are

unassigned.

Page 5

3.1

Assigning Shades/Drapes to the Two Group Remote

(Type C)

Complete step 2 before proceeding. Shades/drapes must be assigned to the master group

before they can be assigned to subgroups 1 and 2. Shades/drapes assigned to sub group 1

and 2 will still respond to the master shade/drape group commands sent from the type A and

B remotes.

Enter Programming Mode

Aim the Remote at the IR Receiver

and Press and Hold Open and

Close buttons for 5 seconds. The

LED’s on the receiving device

will ash

3.2 Enter Assignment Mode

Aim the Remote at the IR Receiver

and tap the Close button. All

unassigned shades/drapes will

open and all assigned drapes/

shades will close.

3.3

For Group 1

For Group 2

Assigning and unassigning

shades/drapes

Select Shade

Aim the Remote at the IR Receiver

and tap the Close button until the

desired shade/drape is selected

(Tapping the open button will

select shades/drapes in the

opposite order). Selected shade/

drape will “wiggle” or move back

and forth a few inches

continuously.

Then

Sivoia QED®Favorite Preset Remote Programming Guide

Page 6

Sivoia QED®Favorite Preset Remote Programming Guide

3Assigning Shades/Drapes to Two Group Remote

(continued)

3.4 Exit Programming Mode

Aim the Remote at the IR Receiver

and Press and Hold Open and

Close buttons for 5 seconds. The

LED’s on the receiving device will

ash. All shades/drapes will return

their previous position.

Assign Selected Shade

Aim the Remote at the IR Receiver

and tap the Lower button. The

wiggling shade/drape will close to

indicate it is assigned.

Unassign Selected Shade

Aim the Remote at the IR Receiver

and tap the Raise button. The

wiggling shade/drape will open to

indicate it is unassigned.

Assign All Shades/Drapes

Aim the Remote at the IR Receiver

and Press and Hold the Close

button for 5 seconds button. All

shades/drapes will close to

indicate they are assigned.

Unassign All Shades/Drapes

Aim the Remote at the IR Receiver

and Press and Hold the Open

button for 5 seconds button. All

shades/drapes will open to

indicate they are unassigned.

Page 7

Sivoia QED®Favorite Preset Remote Programming Guide

4.1

Setting Limits from the IR Remote

The Open and Close limits of shades/drapes can be set from any of the three types of IR remotes.

The shade/drape must be assigned to the master shade group (for Type A and B) remote or sub

group (Type C), to adjust the limit with that remote.

(*) Group 1 programming shown on type C remote. To program with Group 2 use Group 2 buttons.

Enter Programming Mode

Aim the Remote at the IR Receiver

and Press and Hold Open and

Raise buttons for 5 seconds. The

LED’s on the receiving device

will ash

4.2 Select Shade/Drape

Aim the Remote at the IR Receiver

and tap the Close button until the

desired shade/drape is selected

(Tapping the open button will

select shades/drapes in the

opposite order). Selected shade/

drape will “wiggle” or move back

and forth a few inches

continuously.

4.3 Position the Shade/Drape

to the desired limit

Aim the Remote at the IR Receiver

and Press and hold Raise (or

Lower) button until the shade/

drape is in the desired position.

4.4

Open Limit

Aim the Remote at the IR Receiver

and Press and hold the Open

button 5 seconds. The LED’s on

the receiving device will ash to

indicate the limit is stored.

Close Limit

Repeat step 4.3. Aim the Remote

at the IR Receiver and Press and

hold the Close button 5 seconds.

The LED’s on the receiving device

will turn off to indicate the limit is

stored.

Storing the limit

H H

GROUP 2

GROUP 1

Page 8

Sivoia QED®Favorite Preset Remote Programming Guide

4.5 Setting Limits on Additional

Shades/Drapes

Repeat steps

4.2 – 4.4

4.6 Exit Programming Mode

Aim the Remote at the IR Receiver

and Press and Hold Open and

Raise buttons for 5 seconds. The

LED’s on the receiving device

will ash

Setting Limits from the remote (continued)

H H

Page 9

Sivoia QED®Favorite Preset Remote Programming Guide

5.1

Storing Presets

The round silver favorite preset button can return the shade/drape to a favorite preset or

position when tapped once in normal operating mode. By default the favorite preset is stored

midway between the open and close limit. The favorite preset can be changed to a user

deﬁned position with the following procedure.

(*) Group 1 programming shown on type C remote. To program with Group 2 use Group 2 buttons.

Position the Shade/Drape

to the desired location

Aim the Remote at the IR Receiver

and Press and hold Raise (or

Lower) button until the shade/

drape is in the desired position.

5.2 Storing the Favorite Preset

Aim the Remote at the IR Receiver

and Press and hold the round

silver favorite preset button for 5

seconds. The LED’s on the

receiving device will ash to

indicate the limit is stored.

6.1 Locking Presets

Aim the Remote at the IR Receiver

and Press and hold Open and the

Favorite Preset buttons for 5

seconds. The LED on the

receiving device will ash rapidly

then turn off to indicate presets

have been locked.

6.2 Unlocking Presets

Aim the Remote at the IR Receiver

and Press and hold Open and the

Favorite Preset buttons for 5

seconds. The LED on the receiving

device will ash once then turn off

to indicate presets have been

unlocked.

6Locking Presets

The favorite preset can be “locked” to prevent accidental reprogramming of the preset.

Locking the presets from the remote or any other device will prevent presets from being

accidentally changed from the remote or any other device in the system.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lutron Electronics Fernbedienung Handbücher

Lutron Electronics

Lutron Electronics Sivoia QED SVQ-3PIT Bedienungsanleitung

Lutron Electronics

Lutron Electronics FS-5F Bedienungsanleitung

Lutron Electronics

Lutron Electronics Pico PK-2BRL-MAW-L01 Bedienungsanleitung

Lutron Electronics

Lutron Electronics Spacer System SPS-FSIT Bedienungsanleitung

Lutron Electronics

Lutron Electronics PK2-4B Bedienungsanleitung

Lutron Electronics

Lutron Electronics Favorite C-FLRC Bedienungsanleitung

Lutron Electronics

Lutron Electronics RADIO RA2 Bedienungsanleitung

Lutron Electronics

Lutron Electronics CS-YJ-4GC-WH Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung