Lutron Electronics Maestro MS-OPS5M Bedienungsanleitung

Custom Settings (Optional)

Timeout1

1Test Mode2

21 minute

35 minutes3

415 minutes4

530 minutes

Sensor Mode (MS-OPS only)

1Auto-On and Auto-Off

(Occupancy mode)

2Manual-On and Auto-Off

(Vacancy mode)

3Auto-On daylight sensing5and

Auto-Off

Advanced Settings

1Motion sensitivity low

2Motion sensitivity high

3Return all settings to default

Number of flashes Number of flashes Number of flashes

Occupancy sensing switch Occupancy sensing switch

NOTES:

Select your preferred settings from the table below before

proceeding; default settings shown in bold.

For natural light detection, see Footnote 5.

Read all instructions before proceeding.

Press and hold the button(s) indicated in the pictures

below until the lens begins to flash (approximately

5seconds).

The setting is saved after the button is released.

The lens will flash once at each setting.

(Always starts at setting 1.)

EXAMPLE: To set the Timeout to 30 minutes, press

and hold the large button. Release the button after

the lens flashes for the fifth time (approximately

3seconds between flashes).

1Timeout is the delay until lights go off after room is

vacated.

2Short (less than 15-second) timeout for testing sensor

coverage. After entering, device will exit test mode

automatically after 5 minutes, or when any button is

pressed.

3MS-OPS5M and MS-VPS5M default.

4MS-OPS6M2-DV, MS-VPS6M2-DV, UMS-OPS6M2-DV,

and UMS-VPS6M2-DV default.

5Lights turn on only if natural light in room is low. If switch

turns on when there is enough natural light, or if switch

does not turn on when there is not enough natural light,

press the large button within 5seconds of entering the

room. Over time, this interaction will “teach” the switch

your preferred setting.

Occupancy sensing switch

MS-OPS5M, MS-VPS5M

120 V~50/60 Hz

360 W

LFCA

CFL

AFC

CFL |LFCA |AFC

LED

DEL

LED |DEL

450 W

MLV | BVM | BTM

MLV |BVM |BTM

600 W Incandescent |

Halogen |

ELV |BVE |BTE

Incandescent | Incandescente

Halogen | Halógena | Halogène

ELV | BVE | BTE

3 A Combined fan and light load

5 A Ballast |

ro | Ballast

3 A 1/10 HP

entilador

Fan

Ventilateur

Fanr

MS-OPS6M2-DV, MS-VPS6M2-DV,

UMS-OPS6M2-DV, UMS-VPS6M2-DV

120–277 V~50/60 Hz

6 A Lighting

3 A Combined fan and light load

3 A 1/10 HP Fan

120 V~50/60 Hz

Wallplate

(if included)

Adapter plateFaceplate

Pull forcefully.

Remove

faceplate.

Replace

faceplate.

Single-Pole Wiring

Important Notes

Please read before installing.

1.CAUTION: To reduce the risk of overheating and

possible damage to other equipment, DO NOT use to

control receptacles.

2. Install in accordance with all national and local electrical

codes.

3. A ground connection is required for product to function.

Connect green-sleeved wire to ground only in retrofit and

replacement applications. When neutral connection is

available, remove green sleeve and connect to neutral. If

neither wire is present, consult a licensed electrician.

4. Only one (1) sensing switch can be used in a 3-way/multi-

location application.

5. When using with an accessory switch* for 3-way or multi-

location (more than 2locations) applications.

6. Do not exceed twenty (20) devices at 120 V~ or seven

(7) devices at 277V~on a single branch circuit.

7. The ability of the sensing switch to detect motion requires

line-of-sight of room occupants. The sensing switch must

have an unobstructed view of the room.

8. Hot objects or moving air currents can affect the

performance of the sensing switch.

9. For indoor use only. Operate between

32 °F and 104°F (0 °C and 40 °C).

10. Clean with a soft damp cloth only. DO NOT use any

chemical cleaners.

11. Once power has been restored, the sensing switch can

be manually turned on or off within the first 30seconds

but will not automatically control the load for the first

2 minutes.

12. Device makes audible click when turning on or off. This is

normal functionality.

13. Load might not respond if 3-way switch is rapidly turned

on/off.

14. MA-AS, MSC-AS, MA-AS-277, or MSC-AS-277 is

required for multi-location applications.

Go to Step 4

4Install sensing switch in wallbox and

restore power

NOTE: Once power has been restored,

the sensing switch will not automatically

control the load for the ﬁrst 2 minutes.

6Custom Settings (optional)

Leave wallplate off if custom settings are desired.

(See reverse; default settings shown in bold.) To test

sensor coverage, use Test Mode.

5Test the Wiring (3-way only)

!WARNING! Shock Hazard. May result in serious

injury or death. Turn off power before working

with wiring.

Wait 2 minutes after restoring power before testing.

• If sensing switch does not turn the load off and on,

swap its traveler wires.

• If 3-way switch does not turn the load on when it’s

turned off by the sensing switch, swap its traveler

wires.

5If no neutral is present, connect green-sleeved wire to ground

5Remove existing switch

Same color

screws

Ground

When neutral is present in outlet box; remove green sleeve, connect white wire to neutral

Blue

Black

Ground

BareWhite

Travelers

Tagged wire

5Remove existing switch at desired location

Travelers

Tagged wire

Tag the wire connected to different

color screw.

Ground

Modify existing 3-way switch wiring

After

Travelers

Tagged wire

Yellow jumper wire

(included)

Before

Travelers

Tagged wire

Yellow jumper wire

(included)

Tagged wire

(Live or Load) Tagged wire

(Live or Load)

Blue

Black

Ground

Bare

Green-sleeved (2b)*

NOTES

Sensing switch may be installed in either location (see Important Note #4).

3-Way Wiring

WARNING! Shock Hazard. May result in

serious injury or death. Turn off power at

circuit breaker before installing the unit.

When neutral is present in outlet box; remove green

sleeve, connect white wire to neutral

NOTE: Cap blue wire for single

pole applications.

Ground

Bare

White

Blue Black

NOTE: Cap blue wire for single

pole applications.

GroundBareGreen-sleeved

Blue Black

If no neutral is present, connect green-sleeved wire to ground

Blue

Black

GroundBare

Green-sleeved

Travelers

Tagged wire

Neutral

White (2a)*

Neutral

*When neutral is present,

remove green sleeve

and connect white wire

to neutral. If no neutral

available, leave green

sleeve on and connect to

ground.

Learn more about home electrical we have.

Andere Handbücher für Maestro MS-OPS5M

Dieses Handbuch passt für folgende Modelle

Andere Lutron Electronics Schalten Handbücher

Lutron Electronics

Lutron Electronics Maestro MS-B202 Bedienungsanleitung

Lutron Electronics

Lutron Electronics MAESTRO MS-OPS2 Bedienungsanleitung

Lutron Electronics

Lutron Electronics Caseta Claro Smart Bedienungsanleitung

Lutron Electronics

Lutron Electronics Maestro MS-OPS5M Bedienungsanleitung

Lutron Electronics

Lutron Electronics Vive HMS-0 Bedienungsanleitung

Lutron Electronics

Lutron Electronics AuroRa AR-ENT-2S3D Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics Aviena AN-1PS Bedienungsanleitung

Lutron Electronics

Lutron Electronics Nova T NT-1PS Bedienungsanleitung

Lutron Electronics

Lutron Electronics SeeTouch QS Series Leitfaden

Lutron Electronics

Lutron Electronics FS-5F Bedienungsanleitung

Lutron Electronics

Lutron Electronics Maestro MS-B202 Bedienungsanleitung

Lutron Electronics

Lutron Electronics Stanza SZ-1SD Bedienungsanleitung

Lutron Electronics

Lutron Electronics Maestro MS-OPS5M Bedienungsanleitung

Lutron Electronics

Lutron Electronics MAESTRO MS-A102-V Bedienungsanleitung

Lutron Electronics

Lutron Electronics Tu-Wire DVFTU-5A3P Bedienungsanleitung

Lutron Electronics

Lutron Electronics Nova T NT-2WS-AU Bedienungsanleitung

Lutron Electronics

Lutron Electronics Nova N-1PS Bedienungsanleitung

Lutron Electronics

Lutron Electronics Maestro MS-OPS5M Bedienungsanleitung

Lutron Electronics

Lutron Electronics Maestro MS-VPS5M Bedienungsanleitung

Lutron Electronics

Lutron Electronics Maestro MS-OPS6-DDV Bedienungsanleitung

Lutron Electronics

Lutron Electronics Maestro MS-OPS6M2U-DV Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics Sunnata ST-6ANS Bedienungsanleitung

Lutron Electronics

Lutron Electronics Maestro MS-OPS6M2U-DV Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics seeTouch SG-2W Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung