Luxul XGS-1008P Bedienungsanleitung

Simply Connected

Use the XGS-1008P to:

Cost-Effectively Add PoE/PoE+ Capability to Your Network

Deliver Power and Data for up to Eight PoE-Enabled Devices

with a Total Power Budget of 125 Watts

Simplify PoE Device Installation, Including IP Security

Cameras, VoIP Devices, and Wireless Aps

Future Proof Your Network with Gigabit Speeds (10X

Performance of Fast Ethernet)

XGS-1008P

8-Port Gigabit PoE/PoE+ Switch

Quick Install Guide

Use the XGS-1008P to:

Quick Install Guide

XGS-1008P

a: 14203 Minuteman Drive, Ste 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450

LUX-QIG-XGS-1008P 029151044

Quick Install Guide

Model Number: XGS-1008P

8-Port Gigabit PoE/PoE+ Switch

No part of this publication may be modiﬁ ed or adapted in any way, for any

purposes without permission in writing from Luxul. The material in this manual is

subject to change without notice. Luxul reserves the right to make changes to any

product to improve reliability, function, or design. No license is granted, either ex-

pressly or by implication or otherwise under any Luxul intellectual property rights.

An implied license only exists for equipment, circuits and subsystems contained in

this or any Luxul product.

DOCUMENT CONVENTIONS

The following graphical alerts are used to indicate notable situations:

NOTE: Tips, hints, or special requirements that you should take note of.

CAUTION: Care is required. Disregarding a caution can result in data loss

or equipment malfunction.

WARNING!: Indicates a condition or procedure that could result in

personal injury or equipment damage.

FCC COMPLIANCE

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

CONTACT LUXUL

Sales

P: 801-822-5450

E: [email protected]

Technical Support

P: 801-822-5450

E: suppor[email protected]

Simply Connected

Other trademarks and registered trademarks are the property of their respective owners

PACKAGE CONTENTS

The following items are included in the box:

XGS-1008P 8-Port Gigabit PoE/PoE+ Switch

Power Cord

Two L-shaped rack mounting brackets and screws

Four rubber pads

Quick Installation Guide

NOTE: If any of the listed items are missing or damaged, please contact

the reseller from whom you purchased for return/replacement.

HARDWARE DESCRIPTION

Front Panel

The front panel of the XGS-1008P includes eight 10/100/1000 RJ-45 ports as well

as one power LED, eight speed indicator LED’s, eight Link/Activity LED’s, eight PoE

Status LED’s and one PoE Max LED. These LED indicators show the operating status

of the XGS-1008P. Please refer to the detailed description of these indicators in the

Chart on page 3.

XGS-1008P Front Panel View

Quick Install Guide

XGS-1008P

a: 14203 Minuteman Drive, Ste 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450

LUX-QIG-XGS-1008P 029151044

The following chart shows the LED indicators of the XGS-1008P along with an

explanation of the indicator’s properties:

LED Color Status Description

Power Green ON This indicator lights up when the XGS-1008P is

powered

— OFF If this indicator is not lit, please check the power

cable to ensure proper connection to the outlet and

the XGS-1008P.

PoE Max ON (RED) The power of all the connected PoE ports is

between 118W and 125W. No power may be supplied

if additional PDs are connected.

FLASHING

(RED)

The power of all the connected PoE ports is >=125W.

OFF The power of all the connected PoE ports is <118W,

or there is no PD connected to the corresponding

port.

PoE Status Green ON There is a PoE PD connected to the port, which

supply power successfully.

FLASHING The PoE power circuit may be in short or the power

current may be overloaded.

OFF No PD is connected to the corresponding port, or no

power is supplied according to the power limits of

the port.

LINK/ACT Green ON Indicates the port is connected to a device.

Blinking Indicates data activity on the port.

— OFF Indicates the port is not connected to a device.

1000Mbps Green ON There is a 1000 Mbps device connected to the

corresponding port.

—OFF There is a 10/100Mbps device connected to the

corresponding port, or there is no device connected

to the corresponding port.

PREPARING FOR INSTALLATION

System Requirements

Ethernet Cables to connect the XGS-1008P to Ethernet enabled devices

 Power should be AC 100-240V~ 2.0A(Max) 50/60Hz.

Simply Connected

Other trademarks and registered trademarks are the property of their respective owners

Installation Requirements

Install the XGS-1008P in a stable/safe place to avoid any possible damage

Inspect the AC power cord to ensure that it is correctly connected

and undamaged

To avoid electric shock, DO NOT open the XGS-1008P housing (no user service-

able parts inside). Opening the XGS-1008P will void your warranty.

It is recommended that the Grounding connection to the outlet is functioning

properly and the XGS-1008P is positioned away from direct sun light

Ensure there is sufﬁ cient space around the XGS-1008P for proper ventilation and

heat dissipation. It is recommended to have at least 4-6 inches around all sides.

Before Connecting to the Network

Before connecting the XGS-1008P to the network, please check the following:

 Determine placement location. Do not place any heavy articles on the

XGS-1008P.

 Ensure there is adequate space for proper heat dissipation and ventilation

around the XGS-1008P.

 Power socket should be within 4 feet of the XGS-1008P.

 Check power cable to conﬁ rm safe and secure connection.

XGS-1008P INSTALLATION

Installing the XGS-1008P in a Rack

The XGS-1008P can easily be installed in a standard 19” rack. The XGS-1008P includes

two mounting ears for installing and stabilizing the switch. For attaching the mounting

ears and installing the switch within a rack, please refer to the following illustration:

Rack-Mounting the XGS-1008P

Quick Install Guide

XGS-1008P

a: 14203 Minuteman Drive, Ste 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450

LUX-QIG-XGS-1008P 029151044

 Using the included screws, attach the mounting ears to each side of

the switch,.

 Mount the switch in the rack with the LEDs facing outwards. Be sure the

switch is level and properly secured within the rack.

Desktop Setup

For use as a desktop device, position and apply the included rubber feet to the

bottom of the XGS-1008P.

Attaching the Rubber Feet to the XGS-1008P

Connecting Devices

Use standard Ethernet CAT5, CAT5e or CAT6 cable to connect the XGS-1008P to a

device as described below. The XGS-1008P will automatically adjust to the charac-

teristics (speed/duplex) of the device to which it is connected. The PoE function is

autosensing. As long as the powered device is 802.3af/at compliant, the switch will

provide power.

NOTE: Legacy PoE devices that need more than 30Watts can not be

Simply Connected

Other trademarks and registered trademarks are the property of their respective owners

Connecting the XGS-1008P to a Device

When a device is properly connected, the Link/ACT LED for each port

lights up green. Please refer to the LED Indicators section for deﬁ nitions and

troubleshooting.

Connecting to a Router or Other Switch

Connecting the XGS-1008P to a Router and Devices

When a device is properly connected, the Link/ACT LED lights up green. Please refer

to the LED Indicators section for deﬁ nitions and troubleshooting.

Information on this document supersedes all previous versions. Products and documents

subject to change without notice. Products may be discontinued without notice.

LUX-QIG-XGS-1008P

029151044

a: 14203 Minuteman Drive, Ste 201, Draper, UT 84020-1685

luxul.com | 801-822-5450

FCC Statement:

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment uses and can radiate radio

frequency energy, and if not installed and used in accordance with the instructions may cause

harmful interference to radio communications. However; there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

Hereby, Luxul, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020, declares that

this Luxul XGS-1008P is in compliance with the essential requirements and other

relevant provisions of Directive 2006/95/EC.

For a copy of this report send a self addressed stamped envelope to:

Luxul CE, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020.

Industry Canada

CAN ICES-3(A)/NMB-3(A)

Inhaltsverzeichnis

Andere Luxul Schalten Handbücher

Luxul

Luxul AMS-2600 Bedienungsanleitung

Luxul

Luxul AMS-4424P Bedienungsanleitung

Luxul

Luxul XFS-1816P Bedienungsanleitung

Luxul

Luxul AMS-4424P Bedienungsanleitung

Luxul

Luxul Xen XGS-1008 Bedienungsanleitung

Luxul

Luxul XMS-1010P Bedienungsanleitung

Luxul

Luxul XFS-1816P Bedienungsanleitung

Luxul

Luxul AGS-1008M Bedienungsanleitung

Luxul

Luxul AMS-2616P Bedienungsanleitung

Luxul

Luxul XFS-1084P Bedienungsanleitung

Luxul

Luxul Xen XGS-1008 Bedienungsanleitung

Luxul

Luxul XMS-1208P Bedienungsanleitung

Luxul

Luxul XFS-1084P Bedienungsanleitung

Luxul

Luxul XGS-1005 Bedienungsanleitung

Luxul

Luxul XMS-7048P Bedienungsanleitung

Luxul

Luxul AMS-1208P Bedienungsanleitung

Luxul

Luxul XMS-1010P Bedienungsanleitung

Luxul

Luxul AMS-2624P-E Bedienungsanleitung

Luxul

Luxul AMS-1816P Bedienungsanleitung

Luxul

Luxul XMS-5248P Bedienungsanleitung

Luxul

Luxul XMS-1008P Bedienungsanleitung

Luxul

Luxul XMS-1008P Bedienungsanleitung

Luxul

Luxul Xen XGS-1008 Bedienungsanleitung

Luxul

Luxul AMS-1208P Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung