Lynx Testor lite 3G Bedienungsanleitung

Testor | lite 3G

PTG 1802

User Guide

Revision 1.3 Firmware 715 and above

LYNXTechnik AG®| Broadcast Television Equipment

Connecons / Layout .......

What’s in the Box .............

User Interface ..................

Power / Charging .............

Charging ............................

Charge Times .....................

Power ON/OFF ................

Switching ON .....................

Switching OFF ....................

Automac Shutdown .........

SDI Outputs .....................

270Mbit and 1.5Gbit .........

3Gbit ..................................

Seng Video Format .........

Selecng Test Paerns .....

Color Bars ...........................

Flat Field .............................

Mono Paerns ....................

Misc Paerns ....................

Using 3D paerns ..............

3D paerns ........................

Selecng Overlays ...........

Circle Overlay .....................

Text Overlay .......................

Cage / Markers Overlay ...

Seng Audio ..................

Audio Generators ...............

Audio Embedders ..............

Sync Output.....................

User Sengs....................

System Sengs..................

Baery Timeout.................

Oscillator..............................

User Presets....................

USB Port..........................

Firmware Upgrade.............

Baery Replacement.......

Service & Support............

Warranty & Registraon...

Product Registraon.........

Warranty............................

Specicaons......on back side

Contents

SDI Outputs Sync Input or Output

Power Switch

USB Port

(Power/Charging/Firmware updates)

Navigaon

Baery Level

Audio Sengs

Selected Paern

Audio Group

Connecons / Layout

The image below shows the connecons / controls and basic layout of the

integrated touch-screen display.

Video Format

What’s in the Box

The Testor lite 3G is supplied with the following accessories: USB-DCP

charger (plus a variety of regional AC plug adapters) a USB Cable, this

User Guide and Safety Instrucons.

Please read safety instrucons rst!

We recommend you fully charge the unit when you rst receive it. Please refer to

the “Power and Charging” secon of this guide for more details.

User Interface

The Testor lite 3G is equipped with a simple and intuive user interface

that is accessed with the integrated touch screen display. The lower half

of the display is dedicated to the menu system which is used to operate

the unit. The basic touch screen buon funcons are shown below:

This type of buon triggers a funcon. i.e. if pressed the

selected funcon will be set as a direct result.

This type of buon shows when a selecon is acve.

Pressing again will have no eect.

This is a menu navigaon buon, pressing it will navigate

deeper into the menu system. As a result the buons

displayed will change to a new set of choices.

This is a “back” buon and pressing this will navigate back

to the previous menu screen.

To assist with the use of the menu system a navigaon aid is provided

aer each feature or funcon’s descripon, an example of the navigaon

aid is below:

Navigaon: HOME > PATTERN > SDI (X) > COLOR BARS (make selecon)

[buon selecons] [x=specic channel e.g. 1 or 2] [perform acon]

Power / Charging

Charging

The Testor lite 3G uses the USB port for external power and charging.

A USB DCP (dedicated charging port) charger and heavy gauge USB cable

are provided to charge the Testor lite 3G. Please only use the supplied

accessories. Using an alternave USB cable may result in the unit not

charging.

The Testor lite 3G can be connected to any standard USB 2.0 port

(computer) to charge the baery. It will take signicantly longer to charge

this way (lower available charge current) and cannot be used while in

operaon.

(If the unit is powered using a PC USB port then no charging will take

place and the Testor lite 3G will run on internal baery power)

If using a USB DCP power source then the Testor lite 3G can be used and

charged at the same me. Ambient operang temperature is 5° to 40°C.

The baery has an internal temperature sensor and will stop charging if

the baery temperature is too high. This can also happen if the unit is

charged and operated at the same me.

Charge Times

When the baery is empty, the following approximate charge mes are

required to fully charge the baery:

• 120 min. from a USB-DCP supply when unit is turned OFF

• 180 min. from a USB DCP supply when unit is turned ON

• 360 min. from a computer USB 2.0 port when unit is turned OFF

A charge status indicator is always visible on the display. A full charge will

provide approximately 4 hours use. When the baery is empty the Testor

lite 3G will shut down automacally.

Baery life is approximately 300 charge cycles. A replacement baery is

available when needed. Part: PTG-BATT

Note: The rechargeable baery is sealed inside the unit. It is not designed for

frequent baery exchange using a spare charged baery. Only change the

baery when the installed unit is no longer holding charge. Some disassembly is

required. Refer to “Baery Replacement” secon of this guide.

Power ON / OFF

Switching ON

When powered OFF, pressing the power buon for 1 second or longer

will power up the unit and it will be fully operaonal within 5 seconds.

The unit will resume with the last used sengs before the unit was shut

down.

(Current sengs are automacally stored on shutdown)

The unit will power up automacally when connected to a USB-DCP

charger.

(The unit can be manually switched OFF to facilitate faster charging)

Switching OFF

There are two ways to manually switch the unit o.

• When the device is powered ON, tapping POWER OFF on the home

screen will ask for a conrmaon before switching o.

• When the device is powered ON, pressing and holding the POWER

buon for 5 seconds or longer will also switch o the unit.

Automac Shutdown

With no user acvity (touch screen use) the unit will automacally shut

down aer a given me period to preserve baery life.

This can be preset to 5, 10 or 20 minutes or NEVER. Refer to the “Baery

Timeout” sengs in this guide to preset this funcon.

Note: While being charged the module will deacvate the automac shutdown.

Navigaon: HOME > SETTINGS > BATTERY TIMEOUT (make selecon)

SDI Outputs

SD-SDI (270Mbit) and HD-SDI (1.5Gbit) SDI Operaon

When the Testor lite 3G is congured for an SDTV video format (270Mbit)

or an HDTV (1.5Gbit) video format, each SDI output is always the same

video format but can have a dierent paern assigned. Each SDI output

can also have dierent embedded audio and the overlays switched ON or

OFF independently (overlays are the same for both outputs)

3G-SDI (3Gbit) Operaon

The 3G-SDI formats (1080p/50/59/60) can be streamed in one of three

possible formats:

• Two individual 1.5G SDI streams, one per BNC connector. SMPTE 372

(Dual Link)

• Two individual 1.5G SDI streams mulplexed into one 3G-SDI stream.

SMPTE 425 Level B (Dual Link)

• One real 3G-SDI stream. SMPTE 425 Level A (Direct Mapping)

The factory default seng is specied as “3G-SDI, SMPTE 425 Level A”

To set the 3G streaming modes:

Navigaon: HOME > STANDARD > 3G STREAMING FORMAT (set mode)

Seng Video Format

The Testor lite 3G can be congured to provide test signals in the

following formats/standards:

SMPTE 259M (SDTV):

525 (480i/59) / 625 (576i/50)

SMPTE 292M (1.5G HDTV)

[1080i 60], [1080i 59.94], [1080i 50], [1080p 30], [1080p 29.97],

[1080p 25], [1080p 24], [1080psf 25], [1080psf 24], [1080psf 23.97],

[720p 60], [720p 59.94], [720p 50], [720p 30], [720p 29.97], [720p 25],

[720p 24], [720p 23.97]

SMPTE 424M (3G HDTV)

[1080p 60], [1080p 59.94], [1080p 50]

2 x SDI outputs are provided. The signal format and frequency is idencal

on both outputs but independent paerns can be selected for each

output. (exepons are dynamic paerns, which are on both outputs)

Navigaon: HOME > STANDARD (select video format)

Selecng Test Paerns

The Testor lite 3G includes a wide variety of test paerns. Each SDI output

can have a dierent stac paern assigned to it. (Dynamic or moving

paerns will be on both outputs)

Stac Color Bar Paerns:

• Full Field Color Bar 100/100

• Full Field Color Bar 100/75

• Split Color Bars 100/100

• Split Color Bars 100/75

• SMPTE 219 Bars

Navigaon: HOME > PATTERN > SDI (X)> COLORBARS (select paern)

Stac Flat Field Paerns:

• Full Field Red

• Full Field Green

• Full Field Blue

• Full Field White

• Full Field Black

Navigaon: HOME > PATTERN > SDI (X)> FLAT FIELD (select paern)

Stac Mono Paerns:

• Pluge

• Cross-Hatch

• 5-Step

• Valid Ramp

• Limit Ramp

Navigaon: HOME > PATTERN > SDI (X)> MONO (select paern)

Miscellaneous paerns

• Mul-burst

• Frequency Sweep

• Pathological EQ/PLL (split)

• Moving Boxes (Dynamic paern)

• EBU AV Sync (Dynamic paern)**

(Note: leaving the EBU menu will cause the sequence to stop)

Nav: HOME > PATTERN > SDI (X)> MISCELLANEOUS (select paern)

**For a compressive guide on the use of the EBU AV sync test paern, please visit

our website for more informaon:

www.lynx-technik.com/en/products/testor/ebu-av-sync-paern

Using 3D (stereoscopic) Test Paerns

3D (stereoscopic) test paerns, consisng of two 1.5G HD-SDI streams

for Le Eye (LE) and Right Eye (RE) can be selected. This is accomplished

by assigning the individual 3D paerns for LE and RE from the provided

3D paerns. The SDI format has to be set to one of the 1.5G HD-SDI

standards (not 3G-SDI).

By default, these two dierent signals will be streamed as two individual

1.5G SDI streams for LE and RE, one per BNC connector, according to

SMPTE 292-1.

As an alternave way of streaming these two 1.5G HD-SDI signals, the

user can enable the “3G Level B Dual Stream” mode. When enabled, the

two individual 1.5G signals will be mulplexed into a single 3G-SDI Level B

Dual Stream signal according to SMPTE 425. In this case, both SDI outputs

have the same signal.

Two dedicated 3D paerns are provided which provide a 3D eect when

viewed in a 3D environment. These comprise of two slightly dierent

paerns for le eye (LE) and right eye (RE).

3D Test Paerns

• 3D Boxes

• 3D Grey Boxes

Nav: HOME > PATTERN > 3D STEREOSCOPIC (Select LE,RE paerns)

NOTE: When seng the Testor Lite for 3D operaon, please rst select an

appropriate SDI format and 3D SDI Streaming mode.

To set the 3D streaming mode:

Nav: HOME > STANDARD > 3D/HD STREAMING FORMAT (set mode)

Selecng Overlays

Several overlay elements can be superimposed into each of the SDI

outputs. Congured overlays are the same for both outputs but can be

turned ON and OFF independently.

Circle Overlay

A 16:9 or 4:3 circle overlay can be superimposed. The circle center point

of the circle is the geometric center of the image.

Navigaon: HOME > PATTERN >SDI (X) > OVERLAY > CIRCLE

Text Overlay

A text-overlay can be added to the SDI outputs. Each output can have a

dierent text. A maximum of 16 characters can be inserted on one line.

The following characters are available for text inseron:

ABCDEFGHIJKLMNOPQRSTUVWXYZ

abcdefghijklmnopqrstuvwxyz

01234567890-_*()/ [SPACE]

Navigaon: HOME > PATTERN >SDI (X) > OVERLAY > TEXT > (select text)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lynx Prüfgeräte Handbücher

Lynx

Lynx Testor Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung