M-Audio Firewire Audiophile Bedienungsanleitung

M-Audio FireWire Audiophile - Users Manual

1 Introduction

2 What’s in the Box

3 About the FireWire Audiophile

4 Features and Technical Features

5 Minimum System Requirements

•Windows

•Mac OS

6 Controls and Connectors

•Front Panel Diagram

•Front Panel Descriptions

•Rear Panel Diagram

•Rear Panel Descriptions

7 Hardware Driver Installation

•Windows XP

•Windows 2000

•Mac OS X

•Mac OS 9

8 Hardware Connections

•Audio

•MIDI

9 The Software Control Panel

•Global Menus

•Mixer Page

•Output Page

•Hardware Page

•About Page

10 Using the FireWire Audiophile

•Monitoring Live Playback

•Using the Headphone Source Selector

•Setting Up Your Recording Levels

•Monitoring Your Inputs for Recording

•General Recording Instructions

•Setting the Sample Rate

•Adding Effects While Direct Monitoring

•Using the Aux Send as a Separate Monitor Mix

•Using the Level Controller Assignments

11 Troubleshooting

12 Contact Us

13 Product Specs

14 Warranty

1 Introduction

Thank you for choosing the M-Audio FireWire Audiophile. The FireWire Audiophile has

been designed to give you a professional, portable audio and MIDI interface for your

laptop or desktop computer. Using the convenience and dependability of the IEEE-1394

(FireWire) bus, the FireWire Audiophile provides your computer with a high-

performance, high-resolution multi-channel interface, as well as sixteen channels of MIDI

in and out--all in a rugged, lightweight, and highly portable design.

The FireWire Audiophile was created with the laptop-based DJ or live performer in mind,

while still being the perfect audio upgrade for recording and playing back audio in any

portable or home studio configuration. Its front-panel headphone output boasts a high

efficiency, low distortion amplifier that delivers the power and volume you need on stage,

multiple headphone sources with selectable muting of the line outputs for quick cueing,

and a dedicated level control to help you stay on top of your mix, no matter what’s going

on around you.

Even if you’re an experienced sound record-ist, please take some time to read through

this owner’s manual and familiarize yourself with the FireWire Audiophile’s features and

operation. You may also want to refer to your audio software’s documentation to better

understand how the FireWire Audiophile’s features are integrated with the program. Your

experience and enjoyment of your FireWire Audiophile will be greatly enhanced by a

good working knowledge of your audio software.

2 What’s in the Box

Your FireWire Audiophile package contains the following:

•FireWire Audiophile Mobile Recording Interface

•CD-ROM containing driver software and user manual in PDF form

•Printed Quick Start Guide

•CD-ROM containing Reason Adaptedsoftware

•CD-ROM containing Delta Live 2.0software

•Pro-Sessions Sampler CD-ROM

•1 meter 6-pin to 6-pin IEEE 1394 (FireWire) cable

•1 meter 4-pin to 6-pin IEEE 1394 (FireWire) cable

•12VDC 1A Power Supply

•Warranty Card

3 About the FireWire Audiophile

The FireWire Audiophile functions as a four-input, six-output recording and playback

interface. A single IEEE 1394 cable connects the FireWire Audiophile to your computer’s

FireWire port. If your PC is not equipped with a native FireWire port, you may purchase

a FireWire PCI card at any computer electronics retailer (The FireWire Audiophile should

only be used with native FireWire ports on Macs).

IMPORTANT: The FireWire Audiophile comes with a high quality six-pin to six-pin

FireWire cable. We strongly suggest you use this cable, or one of equal quality, for

optimum audio performance. If your computer is equipped with a four-pin interface, you

will need to obtain a four-pin to six-pin FireWire cable, available at most computer

electronics retailers. Also note that the FireWire Audiophile requires a six-pin FireWire

connection in order to receive bus power; if you have a four-pin connection you will

need to use the supplied power adapter.

(Note: Some computer manufacturers may use a different nomenclature to refer to their

FireWire connections, such as Sony’s “iLink,” or simply “1394” — when in doubt, consult

your owner’s manual.)

IMPORTANT:

It has come to our attention that problems have been reported with several types of

IEEE1394 (“FireWire”) devices, including M-Audio FireWire devices. These problems

occur when using a 6-pin bus-powered connection when plugging and unplugging

external FireWire devices, when both the computer and external device are powered

on. This is commonly referred to as “hotplugging”. In some cases the FireWire port on

the host computer system is rendered permanently inoperable. In other cases the

external FireWire device is rendered permanently inoperable. M-Audio does not want

users of M-Audio FireWire products to experience such costly problems. Therefore, M-

Audio must require that users of M-Audio FireWire devices refrain from

hotplugging any M-Audio FireWire device. You must make your FireWire connection

while both computer and FireWire device are powered off; then power on.In case your

M-Audio FireWire device was not detected by your computer on startup, try the following

troubleshooting options instead of hotplugging it:

1. Turn your M-Audio FireWire device off, wait 30 seconds then power it on.

2. Put your computer into hibernation mode, wait 30 seconds then reactivate it.

3. Restart the computer (don’t turn it off) while the M-Audio FireWire device remains

connected and powered on.

The FireWire Audiophile is equipped with two analog inputs and four analog outputs on

unbalanced RCA connectors. Two more channels of S/PDIF digital input and output are

provided on coaxial connectors. That makes the FireWire Audiophile a four-input, six-

output audio interface capable of high-quality analog and digital I/O in full 24-bit

resolution, at sampling rates up to 96kHz for recording and playback. Its S/PDIF digital

output supports pass-through of AC-3 and DTS encoded multi-channel digital audio,

(Windows and Mac OS X only), and it also gives you sixteen channels of MIDI I/O.

The FireWire Audiophile’s easy-to-use software control panel provides you with powerful

routing and mixing control, creating a virtual six-channel output matrix for your audio

software. You can route any combination of inputs to any outputs, and each mixer

channel supports a virtual aux send for unprecedented flexibility. You can take

advantage of ultra-low latency software monitoring with built-in ASIO drivers, and near

zero-latency direct hardware monitoring.

The front panel headphone Source selector is designed to give you immediate access to

selectable stereo monitor sources, with a dedicated rotary level control. The main front

panel rotary encoder can be assigned via the control panel to control any addressable

software or hardware levels, and the FireWire Audiophile can be powered via the

FireWire bus for total portability.*

*Six-pin FireWire connection only. Use the DC power adapter for four-pin FireWire operation.

4 Features and Technical Features

•2 x 4 unbalanced analog operation on RCA jacks

•Coaxial S/PDIF I/O

•Rotary encoder is assignable to control any software-addressable level, e.g., output

DACs, software returns, or hardware input monitor levels

•Headphone output with rotary encoder level control

•Front panel headphone source switching; can be assigned as a Direct Monitoring

on/off switch

•Status indicator LEDs show Headphone Source or ASIO Direct Monitoring state, as

selected in the control panel

•Versatile mixer/router control panel provides near zero-latency hardware direct

monitoring

•Extremely low-latency hardware/drivers

•MIDI I/O

•S/PDIF activity indicator LEDs for input and output.

•Two 6-pin FireWire ports.

•Power on/off switch with indicator LED

•Bus-powered or powered via included power supply

•Frequency response: 20-40KHz +/- 1dB

•SNR and dynamic range (A-weighted): 102dB ADC, 106dB DAC

•THD + N: 0.00281% @0dBFS (= -91dB)

•Sampling rates – 32k to 96kHz for analog in and out

•Sampling rates – 44.1k, 48k, 88.2k, and 96kHz for S/PDIF in and out

5 Minimum System Requirements

IMPORTANT: The FireWire Audiophile is supported under Windows XP and Windows

2000 — it is not supported under Windows 98 or Windows ME. Also, when running under

Windows 2000, you must be running Service Pack 3 (SP3) or later. For Windows XP, you

must be running Service Pack 1 (SP1) or later. Visit the Windows update web pages to

make certain you have the most current updates and fixes supplied by Microsoft.

On the Mac, the FireWire Audiophile is supported under Mac OS 9.2.2 or later, and Mac OSX

version 10.1.5; 10.2.6 or later. Earlier versions of Mac operating systems are not supported.

Windows

Pentium 3 – 500 MHz or higher

128 MB RAM

DirectX 8.1 or higher

Windows XP (SP1) or Windows 2000 (SP3) — (Windows 98 or Windows ME not supported)

Mac OS

Macintosh G3*500 MHz or higher w/ OS 9.2.2 or greater

G4*500 MHz w/ OS X 10.1.5; 10.2.6 or greater

(higher requirements for Laptops)

128 MB RAM (OS 9), 256 MB RAM (OSX)

OS 9.2.2 or later, or OS 10.1.5 or later

•G3/G4 accelerator cards not supported; native FireWire ports required

6 Controls and Connectors

Front Panel Diagram

Front Panel Descriptions

1 Headphone Output – Accepts a standard 1/4” stereo TRS headphone connector.

2 Headphone Output Level – Controls the output of the headphone level. This

control is independent of the line and S/PDIF output levels.

3 HP Source Monitor Status –These LED indicators display the currently selected

mode of the headphone source switch, either A or B.

4 Headphone Source Selector – This momentary switch selects the monitor source sent

to the headphone outputs, in conjunction with the HP Source settings on the Hardware

page of the Control Panel. The default setting is Out 1/2 = A, Out 3/4 = B. This switch can

also be programmed to turn Direct Monitoring on and off.

5 S/PDIF Input and Output Indicators – The green S/PDIF In LED will glow

steadily to indicate the presence of a valid S/PDIF signal at the S/PDIF input. The

green S/PDIF Out LED will glow steadily to indicate the presence of a valid

S/PDIF signal at the S/PDIF output.

6 Level Controller – The Level Controller is a rotary encoder that is set by default

to control the output monitor level of the FireWire Audiophile’s analog outputs. It

can be assigned to any group of Mixer or Output faders in the FireWire

Audiophile’s software control panel. The available selections are:

•SW return – The levels of the three virtual stereo pairs returning from your computer’s

audio workstation software to the FireWire Audiophile’s software mixer

•Output – The levels of the FireWire Audiophile’s four analog and one stereo digital output

•Input – The levels of the FireWire Audiophile’s 1&2 analog and L/R digital inputs

•Aux Send – The levels of the L and Rvirtual Aux Send buses.

7 Power LED – The Blue Power LED blinks when power is applied to the FireWire

Audiophile, and glows steadily to indicate a valid connection to the host computer.

8 Power Switch – Push-on, push-off power switch turns the FireWire Audiophile on

and off.

Rear Panel Diagram

Rear Panel Descriptions

9 Power Supply Connector – Connect the 12VDC 1A power supply here when

using the FireWire Audiophile with a four-pin FireWire connection. Use only the

power supply provided with the unit or a power supply of an equivalent value.

10 FireWire Connectors – Dual FireWire (IEEE-1394) ports allow you to connect

one to your computer and one to an external device. We recommend connecting

only self-powered devices to these inputs. Bus-powered devices may affect your

audio performance.

NOTE: The FireWire Audiophile provides two 6-pin FireWire ports for your convenience. One

port is used for connection to the host computer. The second port allows other peripheral

devices to connect to the host through the FireWire Audiophile. The FireWire Audiophile can

pass FireWire bus power through this secondary port, however it will not source power to other

devices attached to this port.

11 S/PDIF Coaxial In and Out Connectors – S/PDIF digital input and output on

coaxial RCA connectors.

12 MIDI In and MIDI Out Connectors – MIDI input and output on standard 5-pin

DIN connectors.

13 Line Outputs 1–4 – These are unbalanced analog outputs on standard RCA

connectors at –10dBV line level. When monitoring two-channel stereo audio,

outputs 1 and 2 are the default outputs; any or all output pairs may be selected in

the FireWire Audiophile’s control panel. You may also use the four outputs to

send individual or grouped channels to a mixing console.

14 Line Inputs 1 and 2 – These are unbalanced analog inputs on standard RCA

connectors at –10dBV line level.

Andere Handbücher für Firewire Audiophile

Inhaltsverzeichnis

Andere M-Audio Aufnahmegeräte Handbücher

M-Audio

M-Audio ProjectMix I/O Bedienungsanleitung

M-Audio

M-Audio CTRL49 Bedienungsanleitung

M-Audio

M-Audio FireWire Solo Bedienungsanleitung

M-Audio

M-Audio X-Session Stücklistenhandbuch

M-Audio

M-Audio FireWire 410 Bedienungsanleitung

M-Audio

M-Audio FireWire Solo Bedienungsanleitung

M-Audio

M-Audio MobilePre USB Bedienungsanleitung

M-Audio

M-Audio OT-14 Bedienungsanleitung

M-Audio

M-Audio MacMan Bedienungsanleitung

M-Audio

M-Audio AXIOM 25-49-61 Bedienungsanleitung

M-Audio

M-Audio ProFire Lightbridge Bedienungsanleitung

M-Audio

M-Audio Fast Track Bedienungsanleitung

M-Audio

M-Audio midiman Thru 1x4 Bedienungsanleitung

M-Audio

M-Audio Digipatch 12x6 Bedienungsanleitung

M-Audio

M-Audio Black Box Bedienungsanleitung

M-Audio

M-Audio Fast Track Bedienungsanleitung

M-Audio

M-Audio CODE 25 Bedienungsanleitung

M-Audio

M-Audio Delta 1010 Bedienungsanleitung

M-Audio

M-Audio Keystation 88es Bedienungsanleitung

M-Audio

M-Audio Recording Equipment Bedienungsanleitung

M-Audio

M-Audio FireWire 410 Bedienungsanleitung

M-Audio

M-Audio Oxygen 49 Bedienungsanleitung

M-Audio

M-Audio Keystation 49e Bedienungsanleitung

M-Audio

M-Audio Trigger Finger Pro Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch