M Climate Bobbie Bedienungsanleitung
Installation Instructions
Compatibility
The device is designed for remote ОN/OFF switching of water heaters of
all kinds. It connects to the power network 230V and has the ability to
switch the power of electric water heaters with capacity to 3KW.
Electrical power: AC 230 V+/-10%, 50 Hz
Switching power: 3000 W - max
Switching current: 16А - max
Temperature measurements: from 0 to 90"C for Т1 and Т2,
from 0 to 40"C for Т3
Аccuracy of the measured temperature: +/-5%
Accuracy of electrical power measurements: +/-2%
Accuracy of the measured network voltage: +/-2%
Accuracy of the measured alternating current: +/-2%
Energy consumption: 3VA max
Room temperature and humidity: from 0°C до +40°C/ 0% to 100%
Temperature for usage in storage rooms:
from -10 to +60°C from 0% to 85%
Protection class: IP 24 Class II insulation
Mounting position: according rendered symbols
Power ON/OFF indication: Yes
Indication for electrical power to the electrical heater: Yes
Inside the box
Bobbie
fasteners installation template
temperature sensors 1m three-wire cable
Installation
1. Shut down the electrical power
from the main fuse!
Be sure that you have
turned the power to the
water heater off by using
а phase meter.
electrical switchboard
and
2. Remove the bottom cover of
your water heater.
Use the instructions of your water
heater to remove the cover safely.
Make sure that it’s allowed by the
manufacturer and you don’t lose the
warranty of your water heater.
ОN/OFF Water
heater switch
3. Disconnect the power wires.
Use the stickers inside the box, to mark every
cable of your water heater. The stickers have L,N
and G. Put the stickers to the cables, marked with
the symbols. They are easy to find on the clamps
of every cable. After marking the cables you can
take them off from the clamps.
4. Put the template on the wall.
The template shows you where you should
mark the spots for fixing Bobbie on the wall.
For smooth surfaces (like faience), you can use
double sided foil.
Installation
L N
Use phase meter to be sure there is no electricity
to your power wires.
5. Mount Bobbie on the wall.
Use the fasteners or double sided foil to
make sure that the device is well attached
to the wall.
6. Mount the wires that you’ve
marked in t.3
Connect wire L to position 1, wire N to
position 3 and wire G to position 4.
Installation
1234
1234
To clamp L of your water heater you
should mount the red wire, to clamp
N - the blue one. To clamp G, put the
yellow-green wire.
The extra wire connects Bobbie to your
water heater. Mount the red wire to
position 2, the blue one to position 3 and
the yellow with green strips to postition 4.
8. Mount the extra wire to
your water heater.
Installation
1234
7. Connect the extra wire.
L N
9. Place the bottom cover
of your water heater.
Use the instructions of the
manufacturer.
10. Connect Bobbie’s sensors.
Connect the cable of the sensors into
position 5.
Installation
5
11. Fixate every
cables in the box.
Put every cable in its place and
tighten them with the bracket.
12. Place Bobbie’s front cover.
Place Bobbie’s front cover to
make it look out of the box.
Installation
and
13. Place the sensors to
the pipes of your water
heater.
Mount the red sensor to the
hot water pipe and the blue
one to the cold water pipe.
14. Turn on the electricity from the main switchboard.
Turn ON the switch of your water heater.
Installation
electrical switchboard ОN/OFF Water
heater switch.
Inhaltsverzeichnis
Andere M Climate Controller Handbücher
