M Design True Vision Series Bedienungsanleitung

LUNA GAS TRUE VISION

09-2018

Instructions for installation and use TRUE VISION Gas

INSTRUCTIONS FOR INSTALLATION AND USE

Instructions for installation and use TRUE VISION Gas

VERY IMPORTANT

INSTALLATION INSTRUCTIONS

FOR THE M-DESIGNG GAS

FIREPLACES

THE SUPPLIER TAKES NO RESPONSBILITY FOR ANY

POSSIBLE DAMAGE, POOR WORKINGAPPLIANCES AND

ACCIDENT AS A RESULT OF INCORRECT

INSTALLATION

MAINTENANCE GAS FIREPLACE M-DESIGN

THE M-DESIGN GAS FIREPLACES MUST BE

CHECKED EVERY 2 YEARS AND GET A

MAINTENANCE. THIS IS ALSO TO MAINTAIN YOUR

WARRANTY. IF THIS WILL BE NOT

OBSERVED, THE WARRANTY FELL.

YOU CAN RELY ON M-DESIGN TO MAKE THIS CHECK

FOR YOU, OR YOU CAN DO THIS BY YOURSELF AND

FOLLOW THE METHOD BELOW.

Instructions for installation and use TRUE VISION Gas

SUMMARY

1. GENERAL REMARKS........................................................... 5

2. CONNECTION...................................................................... 5

3. INSTALLING THE FIREPLACE .............................................. 6

3.1.1 Positioning the ﬁreplace............................................... 6

3.1.2 Nearbox (Gasunit)........................................................ 7

3.1.3 The Gas connection .................................................... 8

3.1.4 Electrical connection.................................................... 9

3.1.5 Modiﬁcation natural gaz to propane............................. 9

4. INSTALLING THE CHIMNEY ................................................ 10-13

5. FLAME ADJUSTMENT SETTINGS........................................ 14

6. INSULATION AND FINISHING .............................................. 14

7. CONVECTION CURRENT..................................................... 15-16

8. POSITIONING THE LOGS .................................................... 17-25

9. FIRST-TIME USE .................................................................. 26

10. SAFETY, ADVICE AND MAINTENANCE.............................. 26

11.GUARANTEE....................................................................... 27

12. REMOTE CONTROL .......................................................... 28-30

13. CE CERTIFICATION............................................................ 31-33

14. DRAWINGS........................................................................ 34-47

Instructions for installation and use TRUE VISION Gas

OPEN EN CLOSE THE DOOR

For initial setup, you need to clean the window and clear the ﬁreplace of

any dust and grease that is left behind. This is also the only maintenance

action that may be performed on the device by the user.

Thanks to a patented system, the door can be easily opened at an angle of 45° to allow a user-

friendly cleaning of the window

To close, push the door gently (but not to soft) against the hooks. Make sure that all

hooks are hooked

CLOSING

OPEN

Above the glass (below the upper frame) hooks are provided (left, right and center).

Push it upwards with your ﬁngers. the window can now be opened.

Instructions for installation and use TRUE VISION Gas

1. General remarks

This is an appliance using the closed combustion system, designed for the atmosphere

and comfort of your living-room. It constitutes an efﬁcient source of heat and gives the

impression of a real ﬁre.

The balanced ﬂue appliances are based on the principle of natural extraction from the

ﬁrebox, which eliminates ﬂue gas outside and brings in air (oxygen) from outside the

house which is necessary for combustion of the gas. It uses to this effect two concen-

tric pipes. The internal pipe ensures the elimination of burned gases and the external

pipe brings in combustion air. The advantage of this principle is that the equipment

works independently of the atmosphere which predominates in the house.

2. Connection

This appliance must be connected by an approved installer in accordance with the

most recent

regulations in force. On the basis of your order speciﬁcations, this appliance is designed

for natural or propane gas.

Read the instructions before installing and using this appliance. Before installing the

appliance, please check the local regulations about this type of appliance (identiﬁcation

of the type of gas, etc.) and check that the furnace is adapted to your means of instal-

lationt.

It is imperative that the installer sees to the following:

•The appliance must be subject to an air tightness test of the gas and elimination of ﬂue

gases.

•The concentric pipe, if already available, must be working correctly.

•The running of the control valve, lighting of the pilot light, the main burner and the

thermocouple must all be checked.

This appliance has been programmed and factory sealed. The sealed parts cannot be

modiﬁed. The appliance may therefore also be installed in airtight accommodation and

accommodation equipped with mechanical ventilation. It constitutes ambient heating

even in accommodation equipped with a closed ventilation system.

The appliance must be connected to the type of gas mentioned

on the appliance. Never connect a propane burner to natural gas

or vice versa!

220

Instructions for installation and use TRUE VISION Gas

3. Installing the replace

After having checked the appliance, you are ready to install your appliance. This is

done as follows

3.1.1 Positioning the appliance

Place the appliance on a stable surface using the adjustable feet. Adjust the height of

the appliance turning the bolt ( pic 1 )

Minimum and Maximum hight of the appliance :

Adjusting the height of the appliance Min Max 25mm to 330mm (ﬂoor to under the appliance).

The appliance is standard delivered with a distance from the ground-below the unit = 220 mm.

If you want the ﬁreplace to be installed with a different height, unscrew the nut to remove the feet.

Grind the desired height on foot. The distance between two holes is 40mm. With the ﬁreplace is pro-

vided 4 small saucers. Use to get the stud under your feet.

If you want to install the ﬁreplace at the minimum height of 25mm, measured from the ﬂoor to

Below the ﬁrebox: remove the foot and unscrew the nut below the foot. Aim the nut in

The tarred hole that is located below the hearth in the corner. Do the same for the four feet.

The minimum distance from the ﬂoor to the bottom of the frame is 163 mm.

The appliance must not be placed directly on the oor as

you need to allow natural convection. The appertures for the

air supply (IN) is situated underneath the appliances

Unscrew the bolt under the foot and screw

Into the tapped hole beneath the fireplace.

The minimum distance from the ﬂoor to the bottom of the frame is 163 mm.

Fig. B

Fig. A

Instructions for installation and use TRUE VISION Gas

For safety reasons, The gasbattery or “NEARBOX” is ﬁxed with screws at the rear of the unit

during transport .

THE UNIT CANNOT BE INSTALLED WITH THIS NEARBOX FIXED AT THE REAR, IT IS MAN-

DATORY TO UNSCREW THE BATTERY FROM THE REAR PRIOR TO INSTALLATION .

unscrew 4 screws in the corners

(key 8)

gas connection1/2”

reciever

DFGT-03MC01 V09

Transmitter burner S4965C3029

Gas valva

VK4105ME5004

3.1.2 Nearbox (gasunit)

gas connection1/2”

to main burner

Electro magnet ventil 1 or 2 burners

NEARBOX FOR 1 BURNER

NEARBOX FOR 2 BURNERS

to main burner

(455 2 burners)

to second burner or side burner

GAS SUPPLY TO SIDE BURNER OR SECOND

BURNER (YELLOW)

220V

NEARBOX

Connection Gas 1/2” (provide tap)

Instructions for installation and use TRUE VISION Gas

Opening provided in wall

for maintenance

Cable to ionistation pin

GAS SUPPLY TO MAIN BURNER ( RED)

flexible for GAS

True Vision is provided with

a direct ignition , no starting

pilot

3.1.3 The Gas connection

Valve 1/2”

After the “NEARBOX” has removed from the of the back of the ﬁre, you can place it loosely on the

ground in proximity to the opening provided in the wall of mantelpiece. The device is always con-

nected with an approved gas tap 1/2, and preferably with a yellow gasﬂexible that is reachable at all

times. Provide the mantelpiece with a door so that the valve and the electrical connection is easily

accessible.

Instructions for installation and use TRUE VISION Gas

3.1.4 Electrical connection

These appliances are equipped with a radiographic remote control, making an earthened 220V

socket necessary.

You should bear in mind that the appliance must be connected to all

electrical supplies for the purposes of service.

It’s obligatory to connect an earth current.

3.1.5 Modication natural gaz to propane

Modiﬁcation of the ﬁreplace can only be done by the manufacturer or an approved installer. A

new signal plate is provided.

Instructions for installation and use TRUE VISION Gas

Ø 200/130

Appliance C (min) C (max)

850V / 550V / 550DV / 850DV 2 m 10m

850DC / CL / CR / 650DC / 550DC 2 m 9m

1150V / 1050 DC / CL / CR

850VL / 850DVL

2 m 8m

Ø 200/150

Appliance C (min) C (max)

1300V 2 m 8m

Picture 1: ROOF EXIT (C31)

The concentric ue duct should not be reduced to 150/100 for all True Vision.

Picture 1

4. Installing the chimney

Install the concentric ﬂue duct as indicated by ONTOP - METALOTERM. The only authorised pipes are

ONTOP Metaloterm™. ONTOP-METALOTERM tested our appliances with their conduct and we only

guarantee a good working of the appliance with those. Between the external wall of the pipe and the wall

or the ceiling, you should allow for a clearance of at least 50mm and protection that is suitable against

temperatures of around 130°C. The passage of the front panel cowl in the external wall must be ﬁlled in

using silicone mastic.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere M Design Kamin im Innenbereich Handbücher

M Design

M Design LUNA 700H Bedienungsanleitung

M Design

M Design INTERRA 60 Bedienungsanleitung

M Design

M Design LUNA 850 V Gold Gas Bedienungs- und Wartungshandbuch

M Design

M Design TRUE VISION RUSTICA M Leitfaden

M Design

M Design LUNA GOLD 900CL-CR Bedienungsanleitung

M Design

M Design Luna Diamond Series Bedienungsanleitung

M Design

M Design Luna Diamond Series Bedienungsanleitung

M Design

M Design VENUS GREEN PLUS Series Bedienungsanleitung

M Design

M Design LUNA 700H Bedienungsanleitung

M Design

M Design True Vision 1000 RD Bedienungsanleitung

M Design

M Design Luna Gold Series Bedienungsanleitung

M Design

M Design VENUS Bedienungsanleitung

M Design

M Design LUNA 1000 DH Gold Gas Bedienungsanleitung

M Design

M Design LUNA 700H Bedienungsanleitung

M Design

M Design VENUS GREEN PLUS 700 Bedienungsanleitung

M Design

M Design INTERRA 60 Bedienungsanleitung

M Design

M Design ARGENTO H Series Bedienungsanleitung

M Design

M Design Luna Gold 700 H+ Bedienungsanleitung

M Design

M Design LUNA DIAMOND 100DH Bedienungsanleitung

M Design

M Design luna diamond 550 v Bedienungsanleitung

M Design

M Design LUNA 850 V Gold Gas Bedienungsanleitung

M Design

M Design VENUS GREEN PLUS Series Bedienungsanleitung

M Design

M Design DIAMOND Gas 550V Bedienungsanleitung

M Design

M Design VENUS DHT Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch